- DL manuals
- Xantrex
- Power Supply
- XPower Powerpack 300
- Owner's Manual
Xantrex XPower Powerpack 300 Owner's Manual
Summary of XPower Powerpack 300
Page 1
Xantrex inverter 300 owner’s guide 44 5- 0 1 3 9 -0 1- 01 pr in te d i n ch in a web: www.Xantrex.Com email: customerservice@xantrex.Com phone: 1-604-422-8595 phone: 1-800-670-0707 (toll free in north america) fax: 1-604-420-1591 fax: 1-800-994-7828 (toll free in north america).
Page 2
About xantrex xantrex technology inc. Is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to 1 mw utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-alo...
Page 4
Contents 1 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Important safety information . . . . . . . . . . . . . . . . . . 2 warnings and cautions . . . . . . . . . . . . . . . . . . . . . . . . 2 3. Xantrex 300 inverter features . . . . . . . . . . . . . . . ...
Page 5
2.
Page 6
1 introduction thank you for purchasing the xantrex 300 inverter. The 300 inverter is part of a family of advanced, high- performance power inverters from xantrex, the leader in the field of high-frequency inverter design. Connected to the 12 volt outlet in your vehicle or boat or directly to your b...
Page 7
2 2 important safety information if the 300 inverter is connected or used incorrectly, hazardous conditions may be created. Read and save this safety information, and pay special attention to all caution and warning statements in the guide and on the inverter itself. Warnings and cautions are indica...
Page 8
3 warning! Risk of fire or explosion. The 300 inverter contains components that tend to produce arcs or sparks. To prevent fire or explosion, do not install the inverter in compartments containing batteries or flammable materials or in locations that require ignition- protected equipment. Warning! F...
Page 9
4 caution! Risk of damage to the 300 inverter. Reverse battery polarity (negative connected to positive; positive connected to negative) will damage the 300 inverter, and it will require servicing. Damage caused by reverse polarity is not covered by your warranty. Caution! Risk of damage to recharge...
Page 10
5 3 xantrex 300 inverter features this section describes the main features of the 300 inverter. Figure 1 shows the inverter’s ac panel. Figure 1 ac panel on the 300 inverter (european ac outlet) ➀ ac outlet an ac outlet is located on one end of the inverter. It allows you to plug in a 230 volt ac pr...
Page 11
6 when the inverter is connected to a dc power source and the on/standby switch is on, ac power is available at the outlet. ➂ power light the green pwr light is on all the time when the on/standby switch is on. ➃ fault light the red light indicates that the inverter has shut down because of low or h...
Page 12
7 ac outlets depending on your geographic location, your 300 inverter will have one of the following ac outlets. Figure 2 european ac outlet figure 3 british ac outlet figure 4 australian and new zealand ac outlet.
Page 13
8 4 connecting the 300 inverter this section explains how to connect the 300 inverter. Choosing a location for the best performance, choose a location that is: • dry do not expose the inverter to water drip or spray. • cool operate the inverter in ambient temperatures between 0° c and 40° c (32° f a...
Page 14
9 connecting the 300 inverter to dc power you can connect the inverter to a 12 volt dc power source using: • the cigarette plug wire assembly ( page 10 ) • the battery clip wire assembly ( page 11 ) • a hardwired connection to the battery ( page 13 ) your method will depend on the size of the ac loa...
Page 15
10 using the cigarette plug wire assembly loads under 150 watts when you are going to power loads under 150 watts, use the cigarette plug wire assembly. To connect the inverter: 1. Remove the nuts from the dc terminals on the inverter. 2. Place the red ring connector on the inverter’s red (positive ...
Page 16
11 5. Turn on the inverter’s on/standby switch. The pwr light comes on, and ac power is available at the outlet. Note: you may need to turn the vehicle’s ignition key to the accessory position. 6. Plug in the ac load you want to operate. Using the battery clip wire assembly loads greater than 150 wa...
Page 17
12 to connect the inverter: 1. Remove the nuts from the dc terminals on the inverter. 2. Place the red ring connector on the red (positive +) dc terminal, and then screw the red nut on until it is snug. Do not over tighten. 3. Attach the red clip to the red (positive +) battery terminal. 4. Attach t...
Page 18
13 5. Place the black ring connector on the black (negative –) dc terminal, and then screw the black nut on until it is snug. Do not over tighten. Note: a spark may occur when you make this connection. This is normal. 6. Check that both clips are securely connected to the battery terminals. A loose ...
Page 19
14 figure 6 hardwiring the 300 inverter to a 12 volt battery to hardwire the inverter to the battery: 1. Cut the clips off the cable clip wire assembly. (the caution! Fire hazard. The wires in most 12 volt sockets or power outlets are not large enough for loads greater than 150 watts: they will over...
Page 20
15 wires in this assembly are appropriate for loads over 150 watts. The wires in the cigarette plug wire assembly are too small: do not use them.) 2. Using 3.3mm 2 (12 awg) wire or heavier, extend the power cord if you need to, to a maximum total length of 2 meters (6.5 feet) including the existing ...
Page 21
16 6. Remove the nuts from the dc terminals of the inverter. 7. Place the red ring connector on the red (positive +) dc terminal on the inverter, and then screw the red nut on until it is snug. Do not over tighten. 8. Fasten the positive terminal (red wire) to the positive battery post. 9. Fasten th...
Page 22
17 disconnecting the battery • before you disconnect the battery, turn off the ac load, and then turn off the in-line switch. Replacing the in-line fuse • if you need to replace the in-line fuse (see figure 6 ), turn off the in-line switch to disconnect the dc power..
Page 23
18 5 operating the 300 inverter this section describes normal operation as well as several problems that could occur when you use the inverter. If you have a problem, see “troubleshooting” on page 22 . Operating statuses • normal operation when you connect the inverter to your vehicle’s 12 volt sour...
Page 24
19 that occurs when the engine starts may trigger a low voltage shutdown. • ac overload shutdown if you connect an ac load rated higher than 300 watts or 1.3 amps or that draws excessive surge power, the 300 inverter shuts down. The pwr light stays on, and the light comes on to indicate that the inv...
Page 25
20 interference with electronic equipment most ac products operate with the 300 inverter as they would with household ac power with the following exceptions. Buzzing sound some inexpensive stereo systems and “boom boxes” have inadequate internal power supply filtering and buzz slightly when powered ...
Page 26
21 6 battery operating time the battery operating time of the 300 inverter depends on the charge level of the battery, battery capacity, and the amount of power drawn by the particular ac load. With a typical vehicle battery and a 300 watt load, you can expect one or more hours of operating time. To...
Page 27
22 7 troubleshooting this section describes problems you may encounter, the symptoms of each problem, possible causes, and various remedies. The ac load will not operate; the red light is on. Symptom an ac load is plugged in or turned on, operates for one to ten seconds, and then shuts down. Warning...
Page 28
23 symptom the ac load does not operate. The light comes on when the inverter is turned on or when the ac load is turned on or plugged in. The alarm may sound. Symptom the ac load runs for more than one minute, the alarm sounds, and the light comes on. The inverter is warm or hot to touch. The alarm...
Page 29
24 the ac load will not operate; no inverter lights are on. Symptom the cigarette lighter works in the lighter socket, but the inverter does not. Symptom the cigarette lighter does not work in the lighter socket. Possible cause suggested remedy the contact between the plug and the lighter socket or ...
Page 30
25 measured inverter output voltage is too low. Symptom the ac voltmeter reading is 5 to 15 volts too low. Battery operating time is less than expected. Symptom the inverter runs for a while, and then the light comes on. The inverter is cool or warm to touch. Possible cause suggested remedy a standa...
Page 31
26 8 warranty information what does this warranty cover? Xantrex manufactures its products from parts and components that are new or equivalent to new, in accordance with industry standard practices. This warranty covers any defects in workmanship or materials. How long does the coverage last? This ...
Page 32
27 building replacement products. If xantrex repairs or replaces a product, its warranty term is not extended. Xantrex owns all parts removed from repaired products. Service during warranty in order to qualify for the warranty, dated proof of purchase must be provided and the product must not be dis...
Page 33
28 you must obtain a return material authorization (rma) number from xantrex before returning a product directly to xantrex. Do not return a product to xantrex without first obtaining an rma number. When you contact xantrex to obtain service, be prepared to supply the serial number of your product a...
Page 34
29 to return your 300 inverter for out-of-warranty service, contact xantrex customer service for a return material authorization (rma) number, and follow the other steps outlined in “to xantrex” on page 27 . Options for payment, such as credit card or money order, will be explained by the customer s...
Page 35
30 9 specifications specifications may change without notice. Electrical ac receptacles 1 ac output voltage 230 volts ac rms ± 5% ac output frequency 50 ± 3 hz ac output waveform modified sine wave maximum continuous ac output power 300 watts maximum ac output surge power 600 watts dc input voltage ...
Page 36
31 physical regulatory dimensions (l x w x h) 200mm x 103mm x 66mm (7.9 in. X 4.1 in. X 2.6 in.) weight 0.79 kg (1.74 lb.) ce mark low voltage directive emc directive e mark automotive emc directive tuv/type approved certified to en60950
Page 37
32.