1. DL manuals
  2. Xenarc
  3. Monitor
  4. 104OTS
  5. User Manual & Installation Manual

Xenarc 104OTS User Manual & Installation Manual - Index:

Summary of 104OTS

  • Page 1

    1 u u s s e e r r m m a a n n u u a a l l / / i i n n s s t t a a l l l l a a t t i i o o n n g g u u i i d d e e m m o o d d e e l l n n o o . . 1 1 0 0 4 4 o o t t s s warning! Malfunctions are possible if the monitor is operated with an unspecified power supply adaptor or incorrect power voltage....

  • Page 2: Index:

    2 index: i. Introduction ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 3 features‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 3 unpack the monitor‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐...

  • Page 3

    3 i. Introduction ‐ this monitor produces clear images with vivid colors at resolutions from vga up to xga. It uses a graphics adapter of scanning frequency from 30khz to 82khz in horizontal sweep while vertical refresh rate is 56hz to 76 hz continuously. ‐ on screen display provides flexibility wit...

  • Page 4

    4 ii. Installation: power supply & signal connection: power supply: use dc 12vdc power. Hdmi signal: apply hdmi signal  capacitive touch key control /connectors power ( ) use the power switch to turn the power on or off. We recommend turning your system power on first, then the lcd monitor. Press p...

  • Page 5

    5 menu (menu) a. Press menu key to activate osd menu b. This key also registers “ok”; press “up, down” key to move the indicator to the desired item, then press menu key to select and read to adjust. After adjustment, press this key to return to the previous menu. Up ( ▲ ) a. When osd mode is activa...

  • Page 6

    6 espanol 日本語 繁體中文 简体中文 portuguese 한국어 русский main menu recall recall color recall all exit yes no yes no press ”yes” to reset color to factory setting press “yes” to set all settings back to factory setting, except language press “ext” to return to main menu information display information exit − ...

  • Page 7

    7 touch driver installation: 1.0 screen display as below, please click next>..

  • Page 8

    8 2.0 select the set up type; don’t tick the box if ps2 interface is not required, click “next> 3.0 rs232 interface driver install is default, please click next>.

  • Page 9

    9 4.0 you can select to do touch screen calibration after system boot up or not; default setting is” none” 5.0 select to use multi‐monitor system, then press next>.

  • Page 10

    10 6 .0 choose destination location; default folder location shown as below. Press next> 7.0 figure shown below, please press next> to complete installation.

  • Page 11

    11 vi. Mechanical dimension.

  • Page 12: Fcc Class A Warning

    12 vii. Emc warning: fcc class a warning this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a ...

  • Page 13

    13 viii. Product general specification: model p104mr/p104mg lcd panel display size display area optimal resolution brightness contrast ratio response time viewing angle 10.4" 211.2mm x 158.4mm 800 * 600 / 1024*768 300 cd/m² (typ) 500:1(typ) 30 ms (typ) v: 50 /60 , h: 75 /75 video vga signal input co...