O op pe er ra at to or r m ma an nu ua al l initial issue: 02/03 latest revision: 10/03 9.133702.
Operator manual page 9 - 2 initial issue: 02/03 latest revision: 10/03 this page is intentionally left blank..
Table of contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 description of the process . . . . . . . . . . . . . . . . . . . . . . . . . .6 description of the machine . . . . . . . . . . . . . . . . . . . . . . . . . .7 1 - features description . ....
Operator manual page 9 - 4 initial issue: 02/03 latest revision: 10/03 this page is intentionally left blank..
Introduction this manual provides informations for operating the x erox i nterface m odule. Welcome to the xerox interface module. This product is an interface for the docutech 120 prin- ter. The xim will enable in line finishing by receiving sheets from the host printer and sendinig these sheets in...
Description of the process schematic view of the paper path. Operator manual page 9 - 6 initial issue: 02/03 latest revision: 10/03 without rotation with rotation centered input -> centered output centered input -> centered output centered input -> registred output centered input -> registred output.
Description of the machine 1 - features description general: height of the entrance / exit: 860mm / 33.8in. Height of the exit : 860 mm (33.8 in.) or 1020mm (40.1 in.) (adjustable : + 60mm / 2.4in. And - 15mm / .6in.). Operator manual page 9 - 7 initial issue: 02/03 latest revision: 10/03 out out fr...
2 - technical specifications paper type: paper format: operator manual page 9 - 8 initial issue: 02/03 latest revision: 10/03 min: 178 mm (7 in.) max: 470 mm (18.5 in.) paper processing direction min: 254 mm (10 in.) max: 364 mm (14.33 in.) lef sef inches mm envelopes #10 2 to 9"x12" x 4.12x9.5 to 9...
Notes : 1 tabs are fed tab trailing. 2 #10 envelopes enters iot with flap open, flap trailing and front side facing down. Paper orientation , excluding envelopes, encompass both long grain and short grain papers. Brackets ( ) indicate the equivalent size for informational purposes only. 3 korea and ...
Jam detection the display represents the top tray and the paper path area. When part of the mimic is illuminated, there is a problem in this area. Operator manual page 9 - 10 initial issue: 02/03 latest revision: 10/03 top tray this window is blinking when the machine does a set-up, and ligh- ted wh...
How to program a job (rotation or registration)? Refer to printer user interface, not available on xim. Functions to be programmed: - rotation/no rotation. - centered or edge registered output. - higher or lower exit selection... Operator manual page 9 - 11 initial issue: 02/03 latest revision: 10/0...
Jam clearance - job recovery - location of the baffles operator manual page 9 - 12 initial issue: 02/03 latest revision: 10/03 1 2 3 4 5 1 2 3 4 5.
Troubleshooting operator manual page 9 - 13 initial issue: 02/03 latest revision: 10/03 problem green power window not illuminated poor registration paper jams cause no power high paper curl mechanical obstruction high paper curl dirty sensors solution • check that the power cord is connected to the...
Operator manual page 9 - 14 initial issue: 02/03 latest revision: 10/03 this page is intentionally left blank..