1 gsm/gprs/gps mini tracker user manual preface thank you for purchasing the mini gp s tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes...
2 content 1 summary ---------------------------------------------------------------------------------- 3 2 application --------------------------------------------------------------------------------- 3 3 hardware description 3.1 front face -----------------------------------------------------------...
3 1 summary working based on existing gsm/gprs network and gps satellites, this product can locate and monitor any remote targets by sms or gprs. 2 applications z protect the child / the old / the disabled / pet etc z personnel management z covert tracking 3 hardware description accessories includin...
4 3.4 interior 4 specs. Content specs. Dimension. 46(l)x39(w)x13(h) mm weight 35g network gsm/gprs band 850/1800/1900mhz or 900/1800/1900mhz gps chip sirf3 chip gsm/gprs module enfora module gps sensitivity -159dbm gps accuracy 5m time to first fix cold status 45s warm status 35s hot status 1s wall ...
5 5 usage 5.1 sim card installation make sure that there is no call transfer and call display is on , and pin code off . The sms message must in text format, can’t be identified for pdu format. Steps: 5.1.1 open the back cover by loosen the screws 5.1.2 push the foil back and pull it up. 5.1.3 inser...
6 5.2 charger and charging do charge the battery to capacity in 8 -12 hours for the first use. Please use the battery and charger provided by the manufacturer. This unit adopts built-in li-ion battery, and full battery will support around 48 hours use on end. After first use, the battery can be char...
7 5.3 startup z put the sim card in place and tighten the screws.. Z the unit turns on automatically when connecting the tracker with battery,at this time the indicator keep flashing quickly. Z in 30s to 60 seconds the indicator stop flashing when the unit receives gsm signal as well as gps signal. ...
8 5.6 authorization there are only 5 numbers able to be authorized. 5.6.1 setup:send sms admin+password+space+cell phone number to be as a authorized number. The other authorized numbers should be set up by the first authorized number. If the number is successfully authorized, the unit will reply sm...
9 30s,total 5 times.(s: second, m: minute, h: hour). The setting must be in 3 digits and at maximum 255 in value. 5.8.2 to get a geo-info at 30s intervals to the authorized numbers for heaps of times. Setup:send sms t030s***n+password to the unit, it will report a geo-info every 30s,total heaps of t...
10 5.10 movement alert this function is using for the owner to get alarm when the unit moves out of a restricted district.(500m radius). 5.10.1 setup: when the unit stays immobile in a place for 3-10 minutes, the user can send sms move+password to the unit, it will reply “move ok!”. In case of such ...
11 below that rate, it may cause the excursion of the gps signal influenced by clounds etc. 5.12 low battery alert it begins to send sms to the user every 30 minutes when the battery voltage is or less than 3.7v. The alert sms format as below: lat: 22.566923 long: 114.051331 speed:0.00 28/10/09 03:3...
12 5.15 gprs setting in order to use gprs function, the user needs to set ip, port and apn ( access point name ) by cell phone. （ note: some countries or regions should set apn’s user name and apn’s password,please consult your local service operator for information. ） 5.15.1 set an ip address and p...
13 as soon as the ip & port & apn are set up, the user can make a call or send sms to tracker. The tracker will hang up and report the coordinates to ip address. The message format sent by tracker to ip address is as following: serial number + authorized number + gprmc + gps signal indicator + alert...
14 6 cautions please comply with the instructions to extend the unit life: 1. Keep the unit dry. Any liquid, i.E. Rain, moisture, may destroy or damage the inside circuitry. 2. Don’t use & store the unit in dusty places. 3. Don’t put the unit in overheated or overcooled places. 4. Handle carefully. ...
