Xpelair GX12 Installation And Operating Instructions Manual - page 7
I
Istruzioni d’installazione ed uso
Xpelair GX12
LASCIARE QUESTO FOGLIETTO DI ISTRUZIONI INSIEME
AL VENTILATORE, PER USO DA PARTE DELL’UTENTE.
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
2.
Unscrew the four cross - headed screws and lift-off the Fan (Fig. 3).
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
2.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
I
Istruzioni d’installazione ed uso
Xpelair GX12
LASCIARE QUESTO FOGLIETTO DI ISTRUZIONI INSIEME
AL VENTILATORE, PER USO DA PARTE DELL’UTENTE.
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
2.
Unscrew the four cross - headed screws and lift-off the Fan (Fig. 3).
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
2.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
I
Istruzioni d’installazione ed uso
Xpelair GX12
LASCIARE QUESTO FOGLIETTO DI ISTRUZIONI INSIEME
AL VENTILATORE, PER USO DA PARTE DELL’UTENTE.
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
2.
Unscrew the four cross - headed screws and lift-off the Fan (Fig. 3).
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
2.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
I
Istruzioni d’installazione ed uso
Xpelair GX12
LASCIARE QUESTO FOGLIETTO DI ISTRUZIONI INSIEME
AL VENTILATORE, PER USO DA PARTE DELL’UTENTE.
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
2.
Unscrew the four cross - headed screws and lift-off the Fan (Fig. 3).
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
2.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
I
Istruzioni d’installazione ed uso
Xpelair GX12
LASCIARE QUESTO FOGLIETTO DI ISTRUZIONI INSIEME
AL VENTILATORE, PER USO DA PARTE DELL’UTENTE.
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
2.
Unscrew the four cross - headed screws and lift-off the Fan (Fig. 3).
1.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
2.
Remove the inner grill and back draught shutter by first removing the screw
from the underside of the grille then unclipping the bottom of the grille, the
top of the grille can then be released by unclipping the top corner. The
shutter can then be unclipped.
NOTE: The top of the grille can only be released when the screw is removed and
the bottom of the grille has been released (Fig. 2).
Non è previsto l’uso di questo apparecchio da parte di persone
(inclusi i bambini e gli infermi) con menomazioni fisiche, sensoriali
o mentali, o mancanza di esperienza e conoscenze, a meno che tali
persone siano sorvegliate o istruite sull’uso dell’apparecchio da una
persona responsabile della loro sicurezza.
Si devono sorvegliare i bambini, per assicurarsi che non giochino
con l’apparecchio.
Nel cablaggio fisso deve essere inclusa la possibilità di uno
scollegamento fisico dall’alimentazione su tutti i poli in conformità con le
norme sui cablaggi.
Se il ventilatore viene installato in una stanza dove si trova
un’apparecchiatura che fa uso di combustibile, si devono prendere
precauzioni per evitare il riflusso di gas nell’ambiente dalla canna fumaria
del bruciatore.
Questo prodotto non deve essere installato in zona 0.
Non è previsto l’uso di questo apparecchio da parte di persone
(inclusi i bambini e gli infermi) con menomazioni fisiche, sensoriali
o mentali, o mancanza di esperienza e conoscenze, a meno che tali
persone siano sorvegliate o istruite sull’uso dell’apparecchio da una
persona responsabile della loro sicurezza.
Si devono sorvegliare i bambini, per assicurarsi che non giochino
con l’apparecchio.
Nel cablaggio fisso deve essere inclusa la possibilità di uno
scollegamento fisico dall’alimentazione su tutti i poli in conformità con le
norme sui cablaggi.
Se il ventilatore viene installato in una stanza dove si trova
un’apparecchiatura che fa uso di combustibile, si devono prendere
precauzioni per evitare il riflusso di gas nell’ambiente dalla canna fumaria
del bruciatore.
Questo prodotto non deve essere installato in zona 0.
Non è previsto l’uso di questo apparecchio da parte di persone
(inclusi i bambini e gli infermi) con menomazioni fisiche, sensoriali
o mentali, o mancanza di esperienza e conoscenze, a meno che tali
persone siano sorvegliate o istruite sull’uso dell’apparecchio da una
persona responsabile della loro sicurezza.
Si devono sorvegliare i bambini, per assicurarsi che non giochino
con l’apparecchio.
Nel cablaggio fisso deve essere inclusa la possibilità di uno
scollegamento fisico dall’alimentazione su tutti i poli in conformità con le
norme sui cablaggi.
Se il ventilatore viene installato in una stanza dove si trova
un’apparecchiatura che fa uso di combustibile, si devono prendere
precauzioni per evitare il riflusso di gas nell’ambiente dalla canna fumaria
del bruciatore.
Questo prodotto non deve essere installato in zona 0.