- DL manuals
- Xpelair
- Ventilation Hood
- Xcell 150 QV
- Installation And Operating Instructions Manual
Xpelair Xcell 150 QV Installation And Operating Instructions Manual
Summary of Xcell 150 QV
Page 1
1 installation and operating instructions xcell 150 qv xcell 150 qvw mechanical ventilation unit with heat recovery please ensure these instructions are kept safe and accessible at all times..
Page 2
2 table of contents 1 general information .................................................................................................................... 3 2 components and materials of construction ............................................................................. 3 3 regulations an...
Page 3
3 1 general information read all these instructions & warnings fully before commencing installation. These installation and operating instructions must be observed during installation, operation, service and maintenance. This mvhr should only be in- stalled and repaired by a qualified service techni...
Page 4
4 4 application and planning 4.1 application this mvhr is intended for installation in ventila- tion systems in houses, residential buildings and light commercial applications e.G. Offices and meeting rooms etc. Upon completion of the sys- tem, there should be no safety, health or envi- ronmental ri...
Page 5
5 5 assembly and installation 5.1 general information: the mvhr should be aligned horizontally using a spirit level (for reliable condensate drainage). The mains voltage must be 220-240v / 50-60 hz. If mounting on low density walls i.E. Plaster boarded stud walls use the following fixing method: use...
Page 6
6 5.4 duct connections: dwelling extract dwelling supply atmosphere intake atmosphere discharge for ease of installation the duct connections are located on top of the mvhr. - when viewed from the front of the mvhr in a right handed installation, the two duct connec- tions on the left hand side are ...
Page 7
7 5.5 installation 5.5.1 wall-mounting the mvhr for wall-mounting the mvhr, three wall-mounting brackets are supplied. Mark out the fixing holes for the wall-mounting brackets using the diagram provided and drill the holes to suit the fixing screws to be used. Precisely align the three wall-mounting...
Page 8
8 5.8 installation dimensions.
Page 9
9 6 technical data 6.1 air volume flow rates can be adjusted on the pcb by service technicians only: the adjustment potentiometers (3x blue) for the supply air fan and (3x red) for the exhaust air fan are shown on the picture opposite. Port pins for connection of the voltmeter are also provided. 6.2...
Page 10
10 6.5 technical data: technical data units specification voltage / frequency v / hz ~ 220-240v / 50-60 hz max. Current consumption a 0.60 power consumption - speeds 1, 2, 3 w 26 / 48 / 80 air – volume flow rate - speeds 1, 2, 3 mƒ/h 50 / 100 / 150 air volume flow rate at 90 pa static pressure pa 15...
Page 11
11 u n it c o n n e c tio n t e rm in a ls x c e ll 1 5 0 q v c o n tr o lle d b y a 2 -s p e e d (m s 2 ) c o n tr o lle r. X c e ll 1 5 0 q v in te rn a l t e rm in a ls g re e n / y e llo w b ro w n b lu e (b l) (b n ) (g /y ) 1 p h a s e (2 2 0 -2 4 0 v a c ) (5 0 /6 0 h z ) n f u s e l n e ~ n ...
Page 12
12 t t t t t t t ra n s fo rm e r j u m p e r p o s iti o n : j p 1 = o p e n j p 2 = c lo se d j p 3 = o p e n j p 4 = c lo se d j p 5 = o p e n j p 6 = c lo se d j p 7 = o p e n j p 8 = c lo se d j p 9 = o p e n j p 1 0 = o p e n f u s e d s w itc h s p u r (b y o th e rs ). A e p r e f: x c e ll ...
Page 13
13 t t t t t t j u m p e r p o s itio n : j p 1 = o p e n j p 2 = c lo s e d j p 3 = o p e n j p 4 = c lo s e d j p 5 = o p e n j p 6 = c lo s e d j p 7 = o p e n j p 8 = c lo s e d j p 9 = o p e n j p 1 0 = c lo s e d t ra n s fo rm e r g re e n / y e llo w b ro w n b lu e 1 p h a s e (2 2 0 -2 4 0...
Page 14
14 t t t t t t j u m p e r p o s iti o n : j p 1 = o p e n j p 2 = c lo s e d j p 3 = o p e n j p 4 = c lo s e d j p 5 = o p e n j p 6 = c lo s e d j p 7 = o p e n j p 8 = c lo s e d j p 9 = o p e n j p 1 0 = c lo s e d t ra n s fo rm e r q 3 s p c o n tro lle r (9 6 0 0 5 a a ). Q h s c o n tro lle...
Page 15
15 t t t t t t t ra n s fo rm e r j u m p e r p o s iti o n : j p 1 = o p e n j p 2 = c lo s e d j p 3 = o p e n j p 4 = c lo s e d j p 5 = o p e n j p 6 = c lo s e d j p 7 = o p e n j p 8 = c lo s e d j p 9 = o p e n j p 1 0 = c lo s e d q 3 s p c o n tro lle r (9 6 0 0 5 a a ). Q h s c o n tro lle...
Page 16
16 8 controller functions 8.1 ms2 manual 2-speed switch refer to section 7.1 for the relevant wiring diagram. This switch option is for manual control only and therefore none of the automatic control accessories listed below are compatible with this switch. Minimum size of 3-core cable to be used: p...
Page 17
17 8.3 qco 2 co 2 sensor the co 2 sensor will only function in conjunction with the automatic 3-speed switch, refer to sections 7.3 and 7.4 for the relevant wiring diagrams and associated controllers that are compatible with the co 2 sensor. With jumper 10 selected on the pcb, the co 2 sensor is act...
Page 18
18 8.5 automatic defrost (anti-icing protection) in order to prevent the heat exchanger from freezing when the outside temperature is low, a frost protection moni- tor has been integrated (xcell 150 qvw models only). Two temperature ranges can be set via the pcb jumpers 4 and 5 (see table below). Op...
Page 19
19 9 maintenance 9.1 filters the mvhr should never be operated without filters. However, depending on the actual volume of contaminants in the environment, the filters (external air and exhaust air from the mvhr) need to be checked and cleaned at least twice a year and replaced at least on an annual...
Page 20
20 9.4 cleaning the heat exchanger the heat exchanger should be cleaned by a specialist technician as and when required depending on the level of contamination, but at least every 2 years. Contact details for authorised servicing by xpelair approved technicians can be found on the back of this bookl...
Page 21
21 10.2 installation of replacement fans should either fan develop a fault and need to be replaced please contact the uk sales office to order replacement fans or the uk customer care / technical helpline to arrange for fan replacement by applied energy products limited, or our approved agents, cont...
Page 22
22 c) firmly attach string to the two leads of the faulty fan. Note: the string, at least 3 metres long, must be secured tightly but not in a way that will become jammed when pulled through the cable channels inside the unit i.E. No large tied knots. D) remove the bell mouth covering the faulty fan....
Page 23
23 11 customer notes (to record details of filter / recuperator cleaning etc.).
Page 24
24 customer notes (continued).
Page 25
25 customer notes (continued).
Page 26: Maintenance Log
26 maintenance log date action signature/ stamp.
Page 27
27 this xpelair mvhr was purchased from: supplier stamp on ________________________(date).
Page 28
28 guarantee terms and conditions for uk & roi (outside uk & roi contact your local distributor) we, applied energy products, guarantee this product against faulty workmanship and material defects for a period of 5 years from the date of purchase subject to regular servicing by by applied energy pro...