1. DL manuals
  2. Xray
  3. Motorized Toy Car
  4. T2'007
  5. Instruction Manual

Xray T2'007 Instruction Manual

Manual is about: 1/10 Luxury Touring Car

Summary of T2'007

  • Page 1

    Xray model racing cars p.O.Box 103, 911 50 trenčín slovakia, europe phone: +421 32 7440180 info@teamxray.Com xray model racing cars p.O.Box 103, 911 50 trenčín slovakia, europe phone: +421 32 7440180 info@teamxray.Com 1/10 luxury touring car 1/10 luxury touring car 1/10 luxury touring car instructio...

  • Page 2

    2 before you start the t2‘007 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating rc model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for us...

  • Page 3

    3 important notes – electrical • insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they becom...

  • Page 4

    4 symbols used l=r 2x ca oil correct wrong overtightened the threads are stripped. Part bags used assemble left and right sides the same way assemble in the specified order pay attention here assemble as many times as specified (here twice) apply ca glue tools required equipment required equipment i...

  • Page 5

    5 kit the xray t2’007 comes partially pre-assembled. Before starting assembly, disassemble the chassis parts, noting the position and orientation of the parts, particularly the bulkheads. Keep the parts, including the screw hardware, close at hand. In the assembly steps that follow, each section beg...

  • Page 6

    6 factory preassembled grease 966080 c 8 963030 st 3x8 930138 ba 3x8 930508 bb 5x8 930120 b 2.4 front multi-diff™ eu rubber-spec only 30 5000 ball differential with labyrinth dust covers™ - set - 7075 t6 30 5010 alu diff long output shaft - hard coated - 7075 t6 30 5020 alu diff short output shaft -...

  • Page 7

    7 ball differential & front multi-diff ™ 902305 sh m3x5 309319 shim 6x9x2 front multi-diff ™ (eu rubber-spec only) 981212 p 2x12 970100 o 10x1.5 direction of turn front multi-diff ™ settings standard one-way solid one-way full-time solid axle outdrive shafts (left and right) are not connected to eac...

  • Page 8

    8 303134 903306 301122 (eu rubber-spec) 301123 (us foam-spec) 903306 302044 303018 303018 302033 902318 303122 303123 307313 303123 901408 303161 (eu rubber-spec) 303162 (us foam-spec) 902316 302044 302033 901308 303134 903306 903306 903306 903306 302018 302018 303134 302044 302033 902316 303134 302...

  • Page 9

    9 903306 sfh m3x6 901308 sb m3x8 901408 sb m4x8 901308 sb m3x8 901408 sb m4x8 rear left arm rear right arm right rear arm front left arm front right arm left rear arm rear arms 2. Front & rear suspension 3mm 2.0mm 3mm 4x8mm 3x8mm l=r front left arm front right arm l=r completed assembly 3x8mm 4x8mm ...

  • Page 10

    10 detail 2. Front & rear suspension 47.5 mm 3x16mm 51.5 mm 3x7.5x1.5mm 3x6x2mm 3x6x1mm 3x7.5x1.5mm 3x16mm 3x18mm detail detail 2x 1:1 l=r l=r 2x 3x7.5x1.5mm 3x7.5x1.5mm 3x16mm detail l=r rear left arm rear right arm roll center position: -0.75mm roll center position: 0mm standard setting roll cente...

  • Page 11

    11 305431 305784 (eu rubber-spec) 305886 (us foam-spec) 940510 902306 303044 306513 903306 902306 302022 902305 302078 941015 305000 302078 940510 965050 305575 305519 981212 302078 902306 902306 302098 902306 303094 302022 305442 941015 302078 305102 (eu rubber-spec) 305000 (us foam-spec) 3. Centra...

  • Page 12

    12 902305 sh m3x5 965050 c5 981212 p 2x12 940510 bb 5x10x4 941015 bb 10x15x4 note orientation xray multi-diff is not included in us foam-spec kit. The us foam-spec kit includes front ball-differential. To loosen front belt: rotate both front nylon hubs in arrow direction (a) to tighten front belt: r...

  • Page 13

    13 902306 sh m3x6 902306 sh m3x6 903306 sfh m3x6 902306 sh m3x6 l=r l=r position the rear top deck inside of the rear drive belt detail ! Important when building the eu rubber-spec chassis, do not use these alu stands for initial set-up. These alu stands are recommended for use only on the us foam-s...

  • Page 14

    14 901302 sb m3x2.5 981210 p 2x10 902312 302663 303141 303361 902205 305350 901304 940510 303210 303032 305231 901302 302664 305240 305323 305340 981210 303351 307321 902314 302663 302346 302291 902205 305350 901304 303210 303032 305240 305323 981210 307221 307455 302664 902306 901302 305231 940510 ...

  • Page 15

    15 902205 sh m2x5 940510 bb 5x10x4 981210 p 2x10 902205 sh m2x5 940510 bb 5x10x4 981210 p 2x10 902310 sh m3x10 53.0 mm 52.5 mm 1:1 1:1 4. Front & rear transmission 1r = right suspension block 1° outboard toe-in 1l = left suspension block 1° outboard toe-in 2x completed assembly left steering block =...

  • Page 16

    16 303141 shim 3x5x1 902306 sh m3x6 902312 sh m3x12 307455 pb 5mm 901304 sb m3x4 1:1 4. Front & rear transmission rear view quick roll center tm tabs in lower inner holes 25 mm 2x 3x5x1mm l=r tighten gently after you tighten the screw into the upright, pull the linkage upward so the ball joint "snap...

  • Page 17

    17 902306 sh m3x6 902314 sh m3x14 307455 pb 5mm 901304 sb m3x4 1:1 4. Front & rear transmission front view 23 mm 2x l=r "4l" "4r" detail step "click" tighten gently quick roll center tm tabs in lower inner holes initial position after you tighten the screw into the upright, pull the linkage upward s...

  • Page 18

    18 bag 30 1159 alu countersunk shim (4) 30 1178 t2‘007 upper deck - narrow - rubber-spec - multi-flex™ 30 1179 t2‘007 upper deck - wide - foam-spec - multi-flex™ 30 2504 xray quick-saver™ - adjustable servo saver set 30 2551 servo saver plastic cover - eccentric (2) 30 2581 t2‘007 composite servo ho...

  • Page 19

    19 307455 pb 5mm 902310 sh m3x10 902305 sh m3x5 902306 sh m3x6 903306 sfh m3x6 930407 bb 4x7x2.5 307455 pb 5mm 902310 sh m3x10 right steering rod 63.5mm left steering rod 65.5mm servo link ! Important the hole in top deck for the eccentric bearing holder is not directly along the centerline of the t...

  • Page 20

    20 30 3241 ball universal 5.8 mm hex (4) 30 8035 composite pistons adjustable + non-adjust. (set 2+6) 30 8040 shock adj. Nut alu + o-ring (4+4) 30 8080 shockabsorber membranes (4) 30 8090 shock foam inserts (4) 30 8301 t2 xray shock absorber-set 4-step - short (2) 30 8316 t2 shock ball joint - open ...

  • Page 21

    21 1. Insert the larger #970050 (o 5x1) o-ring onto the shock body, until it seats around the shock body extension. 2. Lubricate the small #971031 (o 3.1x1.6) o-ring with a drop or two of shock oil. Taking care not to rip or damage the o-ring, slide it over the end of the shock rod. 3. Install the e...

  • Page 22

    22 bag 30 1202 t2 composite bumper 30 1218 t2 composite upper holder for bumper 30 1322 t2 front body mount set 6mm 90 2306 hex screw sh m3x6 (10) 90 3308 hex screw sfh m3x8 (10) 90 3310 hex screw sfh m3x10 (10) 902306 308301 301322 301218 981212 301202 301222 960030 903308 903310 903310 903308 3013...

  • Page 23

    23 903308 sfh m3x8 981212 p 2x12 902306 sh m3x6 initial position front shock (silver spring - eu) (light-purple spring - us) l=r 7. Front & rear assembly initial position l=r.

  • Page 24

    24 bag 07 902306 sh m3x6 981212 p 2x12 902308 sh m3x8 301332 981212 902308 308301 902306 l=r 7. Front & rear assembly 30 1332 t2 rear body mount set 6mm 90 2306 hex screw sh m3x6 (10) 90 2308 hex screw sh m3x8 (10) 98 1212 pin 2x12 (10) 30 8301 t2 xray shock absorber-set 4-step - short (2) initial p...

  • Page 25

    25 bag 306200 903308 903308 not included 902308 not included from servo 902306 960140 960140 306131 903306 903306 903308 306300 309402 306310 309319 not included not included 08 902308 sh m3x8 903306 sfh m3x6 for improved weight balance, we recommend using a narrow, light servo. 8. Final assembly 30...

  • Page 26

    26 902306 sh m3x6 903308 sfh m3x8 903306 sfh m3x6 903308 sfh m3x8 8. Final assembly double-sided tape (not included) receiver (not included) speed controller (not included) feed the receiver wire into the antenna tube 3x8mm 3x6mm 3x8mm pinion (not included) motor (not included) when installing the m...

  • Page 27

    27 960140 n m4 detail 8. Final assembly warning! Follow the adhesive manufacturer's instructions for proper use and safety. Wear proper eye and hand protection. Ca make sure the wheel nuts are very tight, so the wheels do not loosen during racing. Fibre tape (not included) 6-cell inline battery pack...

  • Page 28

    Xray model racing cars p.O.Box 103, 911 50 trenčín slovakia, europe phone: +421 32 7440180 info@teamxray.Com xray model racing cars p.O.Box 103, 911 50 trenčín slovakia, europe phone: +421 32 7440180 info@teamxray.Com xray model racing cars p.O.Box 103, 911 50 trenčín slovakia, europe phone: +421 32...