Summary of T4
Page 2
2 before you start the t4 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating rc model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for use by...
Page 3
3 important notes – electrical • insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they becom...
Page 4
4 not included to ensure that you always have access to the most up-to-date version of the xray set-up book, xray will now be offering only the digital online version at our web site at www.Teamxray.Com. By offering this online version instead of including a hardcopy printed version in kits, you wil...
Page 5
5 ca at the beginning of each section is an exploded view of the parts to be assembled. There is also a list of all the parts and part numbers that are related to the assembly of that section. The part descriptions are color-coded to make it easier for you to identify the source of a part. Here are ...
Page 6
6 1. Gear differential & front solid axle use tweezers to insert pin. 981210 p 2x10 981210 p 2x10 972050 o 5x2 972050 o 5x2 964050 s 5x15x0.3 964050 s 5x15x0.3 ➊ ➋ ➌ ➍ ➍ ➍ ➎ ➎ ➊ ➋ ➌ ➍ ➎ detail ➎ step step detail 30 4900 xray gear differential - set 30 4910 composite gear diff. Case & cover 30 4930 c...
Page 7
7 964031 s 3.5x10x0.2 1. Gear differential & front solid axle 1. Gear differential & front solid axle 971240 o 24x0.7 after disassembling the gear diff the large o-ring may have an increased size and may be more difficult to re-install. We recommend either inserting the old o-ring carefully in the d...
Page 8
8 composite front solid axle front & rear axles 1. Gear differential & front solid axle 902310 sh m3x10 941015 bb 10x15x4 941015 bb 10x15x4 oil oil oil 903256 sfh m2.5x6 tighten the screws equally but do not tighten them completely. Finish tightening in this order. ➊ ➋ ➌ ➍ detail note orientation be...
Page 9
9 305188 940510 965050 304900 903306 903310 903306 903306 303058-o 302034-o 303056-o 902306 902306 902306 305577 303086 981212 305784 940510 301137 903306 303055-o 902306 902306 902306 305446 960030 305432 302034-o 302760-o 302761-o 302761-o 302760-o 302034-o 302085 302062 302062 305521-k 902304 902...
Page 10
10 gearing adjustment 902304 sh m3x4 965050 c5 981212 p 2x12 940510 bb 5x10x4 spur gears 48p #305778 offset spur gear 78t / 48p #305781 offset spur gear 81t / 48p #305784 spur gear 84t / 48p spur gears 64p #305862 offset spur gear 92t / 64p #305866 offset spur gear 96t / 64p #305870 offset spur gear...
Page 11
11 902306 sh m3x6 902306 sh m3x6 optional: #303071 belt tensioner may be used when the front belt becomes worn and loose. Belt tensioner is not included in the kit and must be purchased separately. Detail to tighten front belt: rotate both front nylon hubs in arrow direction b front belt tension adj...
Page 12
12 bag 03 optional 2x 2x 2x for better stability and to make the car easier to drive, optional #302190 and #303190 graphite stiffeners may be used. Using only 4 screws, the graphite stiffener can be installed or removed which would completely change the characteristics of the car. Stiffeners may be ...
Page 13
13 901310 sb m3x10 901408 sb m4x8 901308 sb m3x8 901408 sb m4x8 front downstop adjustment rear downstop adjustment optional: #303169 - graphite arm - rear more traction and more stable but more fragile (recommended for all kinds of conditions) optional: #302169 - graphite arm - front more traction a...
Page 14
14 toe-in track-width wheelbase roll center anti-squat pro-squat 3x6x1mm 903306 sfh m3x6 903306 sfh m3x6 note orientation eccentric bushings have two different offsets from the center. Middle position = 0.5 mm or 0.5° from center outer position = 1mm or 1° from center the new xray rear alu lower sus...
Page 15
15 903306 sfh m3x6 303129 shim 3x6x1 toe-in track-width wheelbase roll center anti-dive kick-up all possible mounting alternatives of eccentric bushings 3x6x1mm 3x6x1mm eccentric bushings have two different offsets from the center. Middle position = 0.5 mm or 0.5° from center outer position = 1mm or...
Page 16
16 ackermann front toe-in bag 2x l=r oil 3x1mm & 1x2mm composite shims 940508 bb 5x8x2.5 930306 bb 3x6x2.5 903308 sfh m3x8 2x l=r approximately 47mm use bearing oil for all bearings note orientation 6mm thread note orientation tighten the screws gently but fully, and then loosen 1/3 turn so the comp...
Page 17
17 902305 sh m3x5 902306 sh m3x6 303129 shim 3x6x2 303128-k shim 3x6x6 903306 sfh m3x6 chassis flex setting top deck setting h = hitec f = futaba, robe k = ko, jr, airtronics, sanwa for more in-corner steering and better steering response, aluminum servo horns may be used. Important! When the alumin...
Page 18
18 05 bag 901304 362650 302663 303803 302804 930407 303212 980210 305341 302663 303432-o 303455 362650 302663 901303 302663 303212 305350-k 302253 305341 980210 305392 305324 305328 362652 303123-k 303129 302253 362650 302663 303212 302291 901304 362651 303127-k 303354 940510 303455 901303 303432-o ...
Page 19
19 901302 sb m3x2.5 305392 p 2x10 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 rear toe-in track-width drive shafts #305323 50mm - steel #305324 52mm - steel #305326 52mm - alu #305328 50mm - alu #305330 52mm - ecs #305331 50mm - ecs 0° outboard toe-in uprights bearing oil (hudy #106230) use alu 50...
Page 20
20 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 camber adjustment caster adjustment rear toe-in track-width 902310 sh m3x10 standard standard standard standard 55.5 mm 53.5 mm l=r l=r c-hubs front transmission #302334 alu 0° - r+l #302335 alu 2° - right #302336 alu 2° - left #302337 alu 4° - right ...
Page 21
21 roll center 901304 sb m3x4 901304 sb m3x4 303122-k shim 3x6x1 303122-k shim 3x6x1 303127-k shim 3x6x4 303129 shim 3x6x1 alu shim 3x6x1mm alu shim 1x6x1mm left upright = right upright l=r 5mm thread 5mm thread 8mm thread 8mm thread l=r l=r rear alu upper clamp initial position rear alu upper clamp...
Page 22
22 active toe-in 901304 sb m3x4 303123-k shim 3x6x2 303129 shim 3x6x1 903306 sfh m3x6 roll-center alu shim 3x6x2mm alu shim 3x6x2mm 5mm thread 10mm thread tighten gently rear transmission front transmission l=r l=r alternative active rear suspension™ step 2 l=r front alu upper clamp initial position...
Page 23
23 303129 shim 3x6x1 930407 bb 4x7x2.5 ackermann bumpsteer front transmission l=r recommended bumpsteer settings: carpet - 1mm thick shim asphalt - 4mm thick shims the number of shims changes the angles of the steering linkage. When no shims are used, the car is easy to drive into the corner. As the...
Page 24
24 901303 sb m3x3 901304 sb m3x4 anti-roll bars front anti-roll bar front anti-roll bar when the bars are set, verify that both sides move at the same time. If they do, the bars are set up correctly. If not, make sure that both downstops are the same and that the bar wire is flat. If the sides still...
Page 25
25 901303 sb m3x3 901304 sb m3x4 anti-roll bars rear anti-roll bar rear anti-roll bar active rear suspension™ standard suspension if the sides still does not move at the same time, adjust the length of the bar holders. Set the bar into the center, remove the play in the bushings, and tighten the set...
Page 26
26 30 3241 ball universal 5.8 mm hex (4) 30 8037 composite pistons 4-hole 1.0-1.2mm, 3-hole 1.0-1.2mm 30 8042-o t4 alu shock adjustable nut - orange (2) 30 8082 t4 shock absorber membrane (4) 30 8092 t4 shock foam inserts (4) 30 8307-o xray t4 alu shock absorber-set - orange (2) 30 8316 shock ball j...
Page 27
27 shock damping shock oils #106310 100cst #106315 150cst #106320 200cst #106325 250cst #106330 300cst #106335 350cst #106340 400cst #106345 450cst #106350 500cst #106355 550cst #106360 600cst #106370 700cst #106380 800cst #106390 900cst #106410 1000cst #106420 2000cst 970130 o 13x1.5 972030 o 3x2 1...
Page 28
28 shock damping spring rate selection tech tip ➊ ➋ ➌ ➍ follow this tech tip to properly install pivot balls into the top pivot and bottom ball joint. Parts needed: • m3x16 sh screw • m3 shim note that the composite parts have two sides, noticeable around the pivot ball hole: one side has a shiny fi...
Page 29
29 903308 sfh m3x8 903310 sfh m3x10 960030 n m3 bag 07 30 1202 composite bumper 30 1213 graphite bumper upper holder 2.5mm (option) 30 1216 composite bumper upper holder brace 30 1218 composite upper holder for bumper 30 1322 front body mount set 30 1323 front body mount set +1mm height (option) 30 ...
Page 30
30 shock position ride height droop 981212 p 2x12 l=r front shock c2.5 spring 3x6x2 303129 shim 3x6x2 902308 sh m3x8 902312 sh m3x12 optional: #301351-o alu adjustable body post stop (2) very handy, easily externally adjustable body post from swiss 7075 t6 aluminum. Allows for adjustment of body hei...
Page 31
31 shock position ride height droop bag 07 981212 p 2x12 902308 sh m3x8 902308 sh m3x8 optional: #301351-o alu adjustable body post stop (2) very handy, easily externally adjustable body post from swiss 7075 t6 aluminum. Allows for adjustment of body height by 3mm without needing to change the posit...
Page 32
32 bag 902308 sh m3x8 903306 sfh m3x6 306219 shim 3x6x1 306219 shim 3x6x2 306219 shim 3x6x3 07 add shims between servo and alu servo mounts in case you want to move the servo (weight) more forward. There are 3 different thickness of shims. 1mm 2mm 3mm min. Space 0.5mm detail servo screw (not include...
Page 33
33 gearing adjustment 902308 sh m3x8 903308 sfh m3x8 903306 sfh m3x6 for improved weight balance and for more space for electronics, we recommend using a narrow, light servo. Optional: #303061 lipo chassis graphite motor guard double-sided tape (not included) receiver (not included) speed controller...
Page 34
34 960140 n m4 903306 sfh m3x6 903305 sfh m3x5 detail optional: #306186 alu lipo battery backstops (f+r) using the optional stand and shims with screw, there is a posibility to adjust side battery position which has direct influence on the side balance of the car. Optional: #306191 t4 graphite + alu...
Page 35: Ars
35 diff. Position down up diff. Position down up motor mount standard option 2 1 0 -1 -2 3 4 5 6 7 xray t4 2015 ver. 1.0 c 2º camber /degr. Wheelbase /mm 1 0 0 1 1 1 ride height /mm 0º 4º 6º caster ride height /mm front rear rear rear front comments rear downstop /mm camber link location 1 0 -1 -2 2...
Page 36
É/i>8À>ÞÊ É/i>8À>ÞÊ É/i>8À>ÞÊ É8À>Þ,>v} ɳ/i>8À>Þ, rc america, 2030 century center blvd #15, irving, tx 75062, usa phone: 214-744-2400, fax: 214-744-2401, xray@rcamerica.Com.