Summary of T4
Page 2
2 before you start the t4 is a high-competition, high-quality, 1/10-scale touring car intended for persons aged 16 years and older with previous experience building and operating rc model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for use by...
Page 3
3 important notes – electrical • insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they becom...
Page 4
4 not included to ensure that you always have access to the most up-to-date version of the xray set-up book, xray will now be offering only the digital online version at our web site at www.Teamxray.Com. By offering this online version instead of including a hardcopy printed version in kits, you wil...
Page 5
5 ca at the beginning of each section is an exploded view of the parts to be assembled. There is also a list of all the parts and part numbers that are related to the assembly of that section. The part descriptions are color-coded to make it easier for you to identify the source of a part. Here are ...
Page 6
6 1. Gear differential & front solid axle use tweezers to insert pin. 981210 p 2x10 981210 p 2x10 972050 o 5x2 972050 o 5x2 964050 s 5x15x0.3 964050 s 5x15x0.3 ➊ ➋ ➌ ➍ ➍ ➍ ➎ ➎ ➊ ➋ ➌ ➍ ➎ detail ➎ step step detail 30 4900 xray gear differential - set 30 4910 composite gear diff. Case & cover 30 4930 c...
Page 7
7 1. Gear differential & front solid axle 1. Gear differential & front solid axle 964031 s 3.5x10x0.2 971240 o 24x0.7 903256 sfh m2.5x6 tighten the screws equally but do not tighten them completely. Finish tightening in this order. ➊ ➋ ➌ ➍ after disassembling the gear diff the large o-ring may have ...
Page 8
8 composite front solid axle front & rear axles 1. Gear differential & front solid axle 902310 sh m3x10 941015 bb 10x15x4 941015 bb 10x15x4 oil oil oil bearing oil (hudy #106230) bearing oil (hudy #106230) front & rear axles #304900 gear differential #305003 alu diff 34t + 38t pulley #305105 xray al...
Page 9
9 305188 940510 965050 304900 903306 903310 903306 303053-o 302030-o 303054-o 303054-o 902306 902306 305577 303086 981212 960030 305784 940510 301134 903306 902310 902306 305446 305432 303028-o 302030-o 302030-o 303028-o 302085 302062 305521-k 902304 902306 302062 305577 965050 302030-o 2. Central t...
Page 10
10 gearing adjustment 902304 sh m3x4 965050 c5 981212 p 2x12 940510 bb 5x10x4 spur gears 48p #305778 offset spur gear 78t / 48p #305781 offset spur gear 81t / 48p #305784 spur gear 84t / 48p spur gears 64p #305862 offset spur gear 92t / 64p #305866 offset spur gear 96t / 64p #305870 offset spur gear...
Page 11
11 902306 sh m3x6 902306 sh m3x6 optional: #303071 belt tensioner may be used when the front belt becomes worn and loose. Belt tensioner is not included in the kit and must be purchased separately. Detail to tighten front belt: rotate both front nylon hubs in arrow direction b front belt tension adj...
Page 12
12 903306 sfh m3x6 optional: #302050-o -t4 alu lower rear suspension holder - orange. For more steering, we recommend using the optional one piece alu suspension holder. For high grip conditions only, as it decreases rear traction. 2x 2x optional fine roll-center adjustment optional shims may be use...
Page 13
13 front downstop adjustment front anti-roll bar rear downstop adjustment rear anti-roll bar 901308 sb m3x8 901408 sb m4x8 901308 sb m3x8 901408 sb m4x8 rear arms 1-hole #303163 hard (h) #303164 extra-hard (xh) #303167 graphite (g) front arms 1-hole #302163 hard (h) #302164 extra-hard (xh) #302167 g...
Page 14
14 toe-in adjustment track-width adjustment wheelbase adjustment roll center adjustment squat adjustment toe-in adjustment track-width adjustment wheelbase adjustment roll center adjustment squat adjustment toe-in adjustment track-width adjustment wheelbase adjustment roll center adjustment squat ad...
Page 15
15 front toe-in adjustment bag 2x l=r oil 3x1mm & 1x2mm composite shims 303129 shim 3x6x1 940508 bb 5x8 930306 bb 3x6 903308 sfh m3x8 approximately 47mm use bearing oil for all bearings note orientation 6mm thread 3x6x1 note orientation tighten the screws gently but fully, and then loosen 1/3 turn s...
Page 16
16 ackermann adjustment steering throw symmetry chassis flex setting top deck flex setting 902305 sh m3x5 902306 sh m3x6 303129 shim 3x6x2 303128-k shim 3x6x6 h = hitec f = futaba, robe k = ko, jr, airtronics, sanwa 903306 sfh m3x6 initial setting 3x6x2 3x6x6 3x6x2 8 mm thread 10 mm thread 4. Steeri...
Page 17
17 901302 sb m3x2.5 305392 p 2x10 drive shafts #305323 50mm - steel #305324 52mm - steel #305325 50mm - ecs #305326 52mm - alu #305327 52mm - ecs #305328 50mm - alu 05 4x thread lock graphite grease (hudy #106210) only for rear detail step tl tip for easy and comfortable installation of the #305241 ...
Page 18
18 caster adjustment rear toe-in adjustment camber adjustment 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 902205 sh m2x5 940510 bb 5x10x4 980210 p 2x10 902310 sh m3x10 wheel hubs #305350 alu - offset 0 mm #305351 alu - offset -0.75 mm #305352 alu - offset +0.75 mm #305353 alu - offset +1.5 mm 54.5...
Page 19
19 roll-center adjustment 901304 sb m3x4 901304 sb m3x4 303123-k shim 3x6x2 303123-k shim 3x6x2 303127-k shim 3x6x4 303122-k shim 3x6x1 alu shim 3x6x2mm left upright = right upright l=r 4 mm thread 10 mm thread alu shim 3x6x1mm alu shim 3x6x2mm 4 mm thread 10 mm thread "4l" "4r" tighten gently 1:1 2...
Page 20
20 anti-roll bars adjustment 901308 sb m3x8 2x 2x 1:1 901303 sb m3x3 901304 sb m3x4 902310 sh m3x10 307455 pb 5mm 902312 sh m3x12 ackermann adjustment recommended bumpsteer settings: carpet - 1mm thick shim asphalt - 4mm thick shims (longer screw must be used) the number of shims changes the angles ...
Page 21
21 anti-roll bars adjustment 901303 sb m3x3 901304 sb m3x4 902310 sh m3x10 rear anti-roll bar 5. Front & rear transmission 3x4mm 3x3mm 3x3mm when the bars are set, verify that both sides move at the same time. If they do, the bars are set up correctly. If not, make sure that both downstops are the s...
Page 22
22 30 3241 ball universal 5.8 mm hex (4) 30 8037 composite pistons 4-hole 1.0-1.2mm, 3-hole 1.0-1.2mm 30 8042-o t4 alu shock adjustable nut - orange (2) 30 8082 t4 shock absorber membrane (4) 30 8092 t4 shock foam inserts (4) 30 8307-o xray t4 alu shock absorber-set - orange (2) 30 8316 shock ball j...
Page 23
23 shock damping effects of shock damping shock oils #106310 100cst #106315 150cst #106320 200cst #106325 250cst #106330 300cst #106335 350cst #106340 400cst #106345 450cst #106350 500cst #106355 550cst #106360 600cst #106370 700cst #106380 800cst #106390 900cst #106410 1000cst #106420 2000cst 97013...
Page 24
24 tech tip ➊ ➋ ➌ ➍ follow this tech tip to properly install pivot balls into the top pivot and bottom ball joint. Parts needed: • m3 x 16 sh screw • m3 shim note that the composite parts have two sides, noticeable around the pivot ball hole: one side has a shiny finish, the other side has a regular...
Page 25
25 bag 30 1202 composite bumper 30 1218 composite upper holder for bumper 30 1322 front body mount set 30 1325 t4 composite brace for bumper - low (2) 90 2306 hex screw sh m3x6 (10) 90 3308 hex screw sfh m3x8 (10) 90 3310 hex screw sfh m3x10 (10) 96 0030 nut m3 (10) 98 1212 pin 2x12 (10) 30 1224 t4 ...
Page 26
26 shock position adjustment ride height adjustment droop adjustment 903308 sfh m3x8 981212 p 2x12 902306 sh m3x6 l=r front shock c2.7 spring initial position to make the car more stable and easier to drive, move the front shocks forward. Stability increases mainly in chicanes. Note that the car wil...
Page 27
27 shock position adjustment ride height adjustment droop adjustment bag 07 902306 sh m3x6 981212 p 2x12 902308 sh m3x8 l=r 308307-o 902308 902306 981212 301332 to make the car more stable and easier to drive, move the rear shocks rearward. Stability increases mainly in chicanes. Note that the car w...
Page 28
28 bag 902308 sh m3x8 903306 sfh m3x6 306219 shim 3x6x1 306219 shim 3x6x2 306219 shim 3x6x3 07 add shims between servo and alu servo mounts in case you want to move the servo (weight) more forward. There are 3 different thickness of shims. 1mm 2mm 3mm min. Space 0.5mm detail from servo not included ...
Page 29
29 gearing adjustment 902308 sh m3x8 903308 sfh m3x8 903306 sfh m3x6 for improved weight balance and for more space for electronics, we recommend using a narrow, light servo. Double-sided tape (not included) receiver (not included) speed controller (not included) feed the receiver wire into the ante...
Page 30
30 ride height adjustment droop adjustment 960140 n m4 detail 903306 sfh m3x6 903305 sfh m3x5 7. Final assembly warning! Follow the adhesive manufacturer's instructions for proper use and safety. Wear proper eye and hand protection. Ca make sure the wheel nuts are very tight, so the wheels do not lo...
Page 31
31 pinion / t spur gear / t final drive ratio rollout race track name city / country contact one way differential yes solid one way diff. Ball differential solid axle yes yes yes transmission rear front track condition traction technical mixed asphalt carpet fast low medium high esc batteries body w...
Page 32
Www.Facebook.Com/teamxray www.Twitter.Com/teamxray www.Youtube.Com/xrayracing you tube rc america, 2970 blystone lane, suite 109, dallas, 75220 texas, usa phone: 214-744-2400, fax: 214-744-2401, xray@rcamerica.Com.