1. DL manuals
  2. Yaesu
  3. Transceiver Accessories
  4. DMU-2000
  5. Operating Manual

Yaesu DMU-2000 Operating Manual

Other manuals for DMU-2000: Operating Manual, Operating Manual
Manual is about: Data Management Unit

Summary of DMU-2000

  • Page 1

    D ata m anagement u nit dmu-2000 o perating m anual vertex standard co., ltd. 4-8-8 nakameguro, meguro-ku, tokyo 153-8644, japan vertex standard us headquarters 10900 walker street, cypress, ca 90630, u.S.A. Yaesu uk ltd. Unit 12, sun valley business park, winnall close winchester, hampshire, so23 0...

  • Page 2: Able

    Installation and connection (ft-2000/d) ....................................................................................................................... 1 installation and connection (ft-950) ........................................................................................................

  • Page 3: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 1 dm u tr x keyboard supplied connection cable monitor ~ac i n ~a c i n ant e n n a i nstallation and c onnection 1. Make certain that all cables are disconnected from the transceiver. 2. Referring to figure 1, remove the three screws from each side of the trans...

  • Page 4: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 2 1. Make certain that all cables are disconnected from the transceiver. 2. Referring to figure 1, remove the 18 screws that at- tach the bottom case, then remove the bottom case. 3. Refer to figure 2 for the mounting location of the scope unit. There is a disco...

  • Page 5: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 3 i nstallation and c onnection to 1 ant dc in 2 from gnd rot linear tuner ptt rec rem key dmu cat ext spkr input: dc 13.8 v 22 a -tune -tune d m u d m u a n te n n a keyboard supplied connection cable monitor ~ a c i n g n d dc in more than one inch remove the ...

  • Page 6: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 4 power switch press this switch to turn the data management unit on, press this switch again to turn the data manage- ment unit off. If the rear panel power switch is set to the “ o” position, the front panel power switch will not function. Cf card slot this sl...

  • Page 7: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 5 key board jack connect your keyboard (not supplied) to one of these jacks in accordance with your keyboard type (“usb” or “ps/2”). Use the keyboard to input logbook data, and to input your location when setting up the world clock. Audio out jack this jack is f...

  • Page 8: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 6 p lease r ead t his f irst when turning on the transceiver for the first time, please set the local time as soon as possible. If this is not done, the various functions of the world clock and great circle map will not operate correctly. Note: if you wish to ad...

  • Page 9: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 7 4. C hanging the l ocation (1) using the world map  choose (highlight) the “zone” using the [key1()] ~ [key4()] keys, then press the [key7(select)] key.  the name of the country associated with the highlighted time zone may now be selected using the [key1(...

  • Page 10: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 8 p lease r ead t his f irst 6. C orrecting the d ate  use the [key1()] and [key2()] keys to high- light “date,” then press the [key7(select)] key.  use the [key3()] and [key4()] keys to navigate to each column of the date, then use the [key1()] and [key2...

  • Page 11: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 9 p lease r ead t his f irst 8. S etting up d aylight s aving t ime  once you have selected the city to be utilized, use the [key1()] and [key2()] keys to highlight “dst” (d aylight s aving t ime ).  use the [key3()] and [key4()] keys to choose “on” or “of...

  • Page 12: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 10 b efore u sing an e xternal m onitor a bout dmu-2000 d ata m anagement u nit o peration a number of informative and useful displays will appear on the after-market monitor, which is connected to the display terminal on the dmu-2000 rear panel. These include t...

  • Page 13: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 11 b efore u sing an e xternal m onitor a bout dmu-2000 d ata m anagement u nit o peration “m emory c hannel l ist ” screen “w orld c lock ” screen “r otator c ontrol ” screen “a udio s cope / o scillo s cope ” screen “s pectrum s cope ” screen “swr m onitor ” s...

  • Page 14: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 12 b efore u sing an e xternal m onitor main (vfo-a) & sub (vfo-b) fields these areas of the display contain information about the status of the main (vfo-a) and sub (vfo-b) vfos. Mode fields these fields indicate the operating mode in use on the above vfos. Tx ...

  • Page 15: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 13 b efore u sing an e xternal m onitor timer field when the on timer is enabled, “timer” will appear here; when the alarm is enabled, “alarm” will ap- pear in this field. Local time-1 field the current time at your location (local time-1) is displayed here. Loc...

  • Page 16: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 14 a bout the w orld c lock h ow to u se the w orld c lock the world clock displays the time in various countries. The day/night areas are also indicated on the map, includ- ing the grey line near the terminator. The difference be- tween the daylight areas in th...

  • Page 17: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 15 h ow to u se the w orld c lock set (local-time1) s etup see the “please read this first” information (page 6). Format (time format) s etup this procedure lets you choose between 12-hour and 24-hour time display format. 1. While the world map is displayed, pre...

  • Page 18: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 16 h ow to u se the w orld c lock city s election it is possible to enter up to 11 cities in the register. All cities in the register will be displayed on the world clock screen. Advice: the order of the display of the cities can be changed later; for now, pleas...

  • Page 19: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 17 h ow to u se the w orld c lock m iscellaneous w orld c lock s etup o ptions it is possible to change the order of the selected city times, as well as the display color, etc. 1. On the world map screen, press the [key4(list)] key to select the “city name list”...

  • Page 20: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 18 h ow to u se the w orld c lock off t imer and a larm s etup it is easy to set the off timer and alarm times. The off timer countdown intervals of 120/90/60/30/15 minutes, and off, can be selected. For the alarm setting: choose either local-time1 or local-time...

  • Page 21: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 19 n ote.

  • Page 22: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 20 a bout the s pectrum s cope s pectrum s cope this page displays the spectrum scope, which is conve- nient for monitoring band activity. The entire screen will become a spectrum display, and both strong and weak signals from the main (vfo-a) band receiver are ...

  • Page 23: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 21 s pectrum s cope [key3(att)] key (attenuator) press this key repeatedly to attenuate the displayed signal level as shown below. The noise level on the band will vary according to conditions of your antenna, the time of day, etc.; please select the appropriate...

  • Page 24: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 22 s pectrum s cope u sing the ctr (c enter ) d isplay m ode it is possible to view strong and weak signals received on the main band (vfo-a) on the spectrum scope. Also, the lbws (limited band width sweep) mode permits a high-speed, high-resolution sweep of a l...

  • Page 25: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 23 s pectrum s cope miscellaneous functions s earching for s trong s ignals u sing the p eak s earch f eature 1. Press the [key1(func)] key to display the marker setup screen. 2. Press the [key4(p.Srch)] key to move the marker to the highest peak signal frequenc...

  • Page 26: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 24 u sing the lbws (l imited b and w idth s weep ) f unction lbws (limited band width sweep) is a function that sweeps a limited segment of the spectrum scope span without changing the span (bandwidth). As the sweep segment becomes narrower, the speed becomes fa...

  • Page 27: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 25 s pectrum s cope u sing the fix (f ixed ) m ode this feature is convenient when you want to monitor an entire amateur band. The starting point, located at the left edge of the screen, can be set via the menu. Even if the screen span (bandwidth) is changed, th...

  • Page 28: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 26 a bout the a udio s cope and o scilloscope a udio s cope and o scilloscope [key2(mode)] key the scan mode for the left-side audio scope can be changed. Pressing this key changes the audio scope mode as follows: normal wf-1 wf-2 normal ...... “wf-1” and “wf-2”...

  • Page 29: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 27 a udio s cope and o scilloscope u sing the a udio s cope the audio scope is particularly useful when making adjustments to the transmitter, especially when setting up the speech processor and the parametric microphone equalizer. On receive, you can observe th...

  • Page 30: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 28 u sing the o scilloscope the rx waveform can be observed on voice and cw modes. The tx voice waveform can also be observed, allowing optimal adjustments of setup options, and filter settings. 1. Press the [key6(level)] key repeatedly, to set the level appropr...

  • Page 31: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 29 n ote a udio s cope and o scilloscope.

  • Page 32: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 30 a bout the l og b ook l og b ook f unction [key1(func)] key you may use the “check” function to check the log to see if a qso has been made previously with the logged station, and you may also create a summary of qsos by band and mode by pressing this key. Th...

  • Page 33: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 31 l og b ook f unction l og b ook e xample enter key [key1(func)] [key4(edit)] [key7(save/load)] [key4(check)] [key5(summary)] [key6(config)] enter key [key6(setting)].

  • Page 34: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 32 config s etting up to five users may be registered into the logbook. For use in a contest or otherwise, the settings for each operator may be stored for later recall when that operator signs on. The operator's name and callsign identification may be entered i...

  • Page 35: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 33 l og b ook f unction config s etting config setting m ode s etup logging type (setup of log preferences) contest : this is a concise log format, with only the callsign, rst, and rem (remarks) being entered by the operator. The date, time, band, and mode will ...

  • Page 36: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 34 l og b ook f unction l og b ook d ata i nput log data may be entered by the user. Depending on the user (config) setup for “logging type,” there are two logging modes: in the “contest” mode, the operator just enters the callsign, signal report, and the rem (“...

  • Page 37: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 35 quick point: in the step 2 above, before doing a check for a duplicate qso, a copy is made of the qso record, and you may then do editing of that record. Use the [key1()], [key2()], [key3()], and [key4()] keys to select an item from among “call,” “rst,” “...

  • Page 38: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 36 l og b ook f unction l oading l og d ata (load) you may load log data from a cf card into your dmu-2000 (for example, an archive copy, or a log from a different dmu- 2000 or ft dx 9000 series transceiver). Before starting, be sure the cf card containing the l...

  • Page 39: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 37 s ummary c heck you may do a band-by band, a mode-by mode, or an “all log” summary of your log data. M ode - based s ummary c heck 1. Referring to figure on page 31, press the [key5(summary)] key to bring up the “sum- mary mode ” page, and you may then press ...

  • Page 40: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 38 a bout the t emperature /swr i ndication t emperature / swr i ndication [key2(marker)] key this key turns the marker on the swr characteristic graph on and off. The marker lets you identify quickly the frequency on which a particular swr reading is being obse...

  • Page 41: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 39 g raphic m eter d isplays t emperature / swr i ndication vdd the drain voltage of the final fets is measured and displayed here. In the ft-2000 (100 w version) and ft-950, the mea- surement range is 0 ~ 18 v, and the proper voltage is around 13.8 v. On tx, if...

  • Page 42: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 40 t emperature / swr i ndication s wept swr d isplay it is possible to show the swr characteristics and antenna performance on a graph by measuring the swr at various points across an amateur band. In order to measure the swr of the antenna system cor- rectly, ...

  • Page 43: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 41 t emperature / swr i ndication u sing the m arker on the swr g raph it is possible to read the measured swr value by placing the marker onto the desired frequency (measurement test point) of the swr graph. 1. Press the [key2(marker)] key to turn the marker fu...

  • Page 44: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 42 a bout the g reat c ircle m ap / r otator c ontrol function s creen g reat c ircle m ap / r otator c ontrol function [key1(zone)] key this key moves you to a screen used for input of the location of the other station. When the country name and the city name a...

  • Page 45: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 43 g reat c ircle m ap / r otator c ontrol function [key4(mode)] key by pressing this key, the rotation control mode can be selected. With every momentary press, the mode changes as shown below. The mode is indicated in the middle of the display. Manual preset m...

  • Page 46: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 44 manual m ode it is possible to operate/control the rotator manually. If the other station’s location has been entered, the location of the other station and yours will be connected with a line on the great circle map, and you can rotate the antenna manually t...

  • Page 47: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 45 g reat c ircle m ap / r otator c ontrol function preset m ode the preset mode lets you set the desired heading of the rotator in advance, so you can automatically rotate your yaesu rotator to the designated heading. Use of a yaesu rotator (g-800dxa, g-1000dxa...

  • Page 48: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 46 memory m ode it is possible to rotate the antenna automatically to headings, which you store into memory in advance. Use of a yaesu rotator (g-800dxa, g-1000dxa, or g-2800dxa) requires the connection of the optional t9101556 cable to the connector located on ...

  • Page 49: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 47 a bout the m emory c hannel l ist u sing the m emory c hannel l ist [key2(load)] key press this key to load memory data previously saved on the cf card to the dmu-2000. [key3(save)] key press this key to save the current memory data to the cf card. [key5(mask...

  • Page 50: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 48 e rasing a m emory c hannel /r estoring an e rased m emory c hannel you can erase data from any memory channel which is no longer needed. It also is possible to restore (immediately after deletion) erased memory channel data, in case you erase something by ac...

  • Page 51: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 49 u sing the m emory c hannel l ist l oading m emory d ata loading memory data from the cf card to the transceiver’s memory. 1. Press the [key2(load)] key to open the memory loading window. If there are multiple file names stored on the cf card, select the desi...

  • Page 52: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 50 u sing the m enu m ode the dmu-2000 can display the menu mode list of the transceiver on the display. Press and hold in the ft-2000’s [display] key (or the [ent] key of the ft-950 or ft dx 5000) for more than two seconds, white letters will appear in the tabs...

  • Page 53: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 51 m enu m ode c onfiguration c hanges when you want to change a menu mode setting, follow the procedure described below. 1. Press the [menu] button briefly. The monitor will display the menu page. Included on this page will be the menu group, menu item name, me...

  • Page 54: Dmu-2000 D

    Dmu-2000 d ata m anagement u nit page 52 u sing the m enu m ode [key3(save)] key [key3(go)] key s aving m enu c onfiguration d ata you may save the current menu configuration data to the cf card, for archive purposes or for quickly changing extensive transceiver settings for different operating appl...

  • Page 56

    Copyright 2010 vertex standard co., ltd. All rights reserved no portion of this manual may be reproduced without the permission of vertex standard co., ltd. Printed in japan e a e 9 6 x 1 0 5.