語 本 日 hsil gn e lo ña ps e / concert yv1605/1605j 取扱説明書 owner’s manual bedienungsanleitung mode d’emploi manual de instrucciones cst ue d / sia çn ar f h / 『安全上のご注意』を必ずお読みください。 make sure to read “safety precautions” and “cautions when using the instrument”. Lesen sie unbedingt die „vorsichtsmaßregel...
This product utilizes an external power supply (adapter). Do not connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by yamaha. Warning: do not place this product in a position where anyone could walk on, trip ove...
18 safety precautions please obey the following instructions in order to use your vibraphone in a safe manner. Particularly in the case of children, a responsible adult should provide proper instruction on how to properly use and treat the instrument before use. I c o n s a r e u s e d i n t h i s “...
19 safety precautions caution disregard of the warnings denoted with this mark, or misuse of the product can result in injury or property damage. Do not use the instrument in locations with poor venti- lation. Never pull on the cord when disconnecting the ac adapter from the outlet. Always hold the ...
20 nomenclature ■ vibes drive unit ● controller (player side) pedal stay rail no. 1 q power switch turns the power on and off. W motor speed slider controls the fan rotation speed. E led indicator lights when the power is turned on and flashes while the fan is rotating. R start/stop button starts an...
21 confirmation of packing contents q vibes main unit x 1 t resonators (natural tone side) x 1 y resonators (accidental tone side) x 1 w leg (large) x 1 e leg (small) x 1 slide legs slide legs r pedal stay x 1 u ac adapter x 1 i round belt (fan belt) x 2 vibes drive unit: yvm-200 !0 controller x 1 o...
22 for safety, assembly should be performed by at least 2 persons in a location with sufficient space. We recommend to you to assemble the instrument on a soft rug or carpet to avoid scratches in the tone bars. Assembly slide legs slide legs slide leg fixing bolt slide leg fixing bolt slide leg fixi...
23 assembly v place the large leg, small leg and pedal stay so that after assembly each part will be positioned as illustrated. B connect the large leg and small leg with the pedal stay. Insert the pedal stay with its notch facing up into the lower joint of the large leg as far as it will go (aligni...
24 rod connector tighten center rod pedal rod groove m connect the slide legs with the legs. Align the legs from above so that the slide legs slide into the corresponding leg holes. Adjust to the desired height and then securely tighten each slide leg fixing bolt, aligning it with the corresponding ...
25 1 first, place the high sound side onto the corre- sponding resonator holders. Resonator holders assembly . Attach the resonators. Insert the resonators from underneath the frame and rest the high sound side and then the low sound side onto the resonator holders (rubber). * make sure not to confu...
26 bottom view insert mount until it stops driver support fitting bottom view fitting pulley fittings fixing bolts motor unit loosen the fixing bolts. ⁄0 attach the driver. 10-1 loosen the fixing bolts at the bottom of rails (2) and (3) on the high sound side, and slide both fittings in the directio...
27 ⁄1 attach the controller. There are two controller mounting pins on the high sound side of rail (1). Align the two holes in the controller mounts with these pins and hook the controller onto the pins one side at a time. * in case the 8p din cable is misplaced, the following spare part may be orde...
28 assembly pulley ⁄3 attach the round belt (fan belt)*. Slip the round belt (fan belt) over the fan side pulley first, and then pull it over the flange of the driver pulley. * note for service personnel if the belt cannot be mounted because the distance between the pulleys is too wide, or the belt ...
29 ⁄6 height adjustment height adjustment should always be performed by at least 2 persons. To adjust the height of the tone bars, first remove the round belt (fan belt), driver, controller and tone bars*, and loosen the center rod fixing bolts. (* to remove the tone bars, disengage the springs on t...
30 specifications yv1605 range ....................................... F–f3, 3 octaves bars .......................................... Aluminum alloy, 1-1/2" wide, 1/2" thick pitch ......................................... A = 442 hz drive unit ................................. Yvm-200 (pause contro...
10̲yv1605̲back̲cover.Pm6 09.11.19, 4:19 pm page 84 adobe pagemaker 6.0j/ppc wq84190 〒430-8650 静岡県浜松市中区中沢町10-1 版次： 1410 r1 printed in japan.
