- DL manuals
- Yamaha
- Motorcycle
- DRAG STAR XVS1100A
- Owner's Manual
Yamaha DRAG STAR XVS1100A Owner's Manual
Summary of DRAG STAR XVS1100A
Page 1
Printed on recycled paper yamaha motor co., ltd. Printed in japan 2002.09-0.3 ×1 cr (e) 5ks-28199-e4 xvs1100a owner’s manual.
Page 2
Shiro.Fm page 1 thursday, june 7, 2001 11:38 am.
Page 3
Eau04980 cm-01e declaration of conformity we hereby declare that the product: is in compliance with following norm(s) or documents: type-designation: 5sl-00, 5vs-00, 5vx-00, 3ht-00, 5ux-00, 5ux-10, 5ks-00 and 5ks-10 r&tte directive(1999/5/ec) en300 330-2 v1.1.1(2001-6), en60950(2000) two or three-wh...
Page 4
U5kse4.Book page 2 wednesday, september 11, 2002 11:55 am.
Page 5: Introduction
Eau04575 introduction welcome to the yamaha world of motorcycling! As the owner of the xvs1100a, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality prod- ucts, which have earned yamaha a reputation for dependability. Please tak...
Page 6: Important Manual Information
Eau00005 important manual information particularly important information is distinguished in this manual by the following notations: the safety alert symbol means attention! Become alert! Your safety is involved! Warning failure to follow warning instructions could result in severe injury or death t...
Page 7: Important Manual Information
Important manual information ew000002 warning @ please read this manual carefully and completely before operating this motorcycle. @ u5kse4.Book page 2 wednesday, september 11, 2002 11:55 am.
Page 8: Important Manual Information
Important manual information eau04229 xvs1100a owner’s manual ©2002 by yamaha motor co., ltd. 1st edition, august 2002 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U5kse4.Book page 3 wednes...
Page 9: Table of Contents
Table of contents 1 give safety the right of way 1 2 description 2 3 instrument and control functions 3 4 pre-operation checks 4 5 operation and important riding points 5 6 periodic maintenance and minor repair 6 7 motorcycle care and storage 7 8 specifications 8 9 consumer information 9 index eau00...
Page 10
U5kse4.Book page 2 wednesday, september 11, 2002 11:55 am.
Page 11: Give Safety The Right of Way
Give safety the right of way 1 give safety the right of way................................................. 1-1 u5kse4.Book page 1 wednesday, september 11, 2002 11:55 am.
Page 12: Give Safety The Right of Way
1 1-1 eau00021 1- give safety the right of way motorcycles are fascinating vehicles, which can give you an unsurpassed feeling of power and freedom. However, they also impose certain limits, which you must accept; even the best motorcycle does not ignore the laws of physics. Regular care and mainten...
Page 13: Description
Description 2 left view ............................................................................................. 2-1 right view........................................................................................... 2-2 controls and instruments ..................................................
Page 14: Description
2-1 2 eau00026 2- description left view 1. Shift pedal (page 3-8) 2. Fuel cock (page 3-11) 3. Shock absorber assembly spring preload adjusting ring (page 3-17) 4. Helmet holder (page 3-14) 5. Storage compartment (page 3-15) 6. Owner’s tool kit (page 6-1) 7. Fuses (page 6-27) 8. Engine oil level chec...
Page 15: Description
Description 2-2 2 right view 9. Engine oil filter element (page 6-7) 10. Battery (page 6-25) 11. Main fuse (page 6-28) 12. Main switch/steering lock (page 3-2) 13. Air filter element (page 6-11) 14. Brake pedal (page 3-9) u5kse4.Book page 2 wednesday, september 11, 2002 11:55 am.
Page 16: Description
Description 2-3 2 controls and instruments 1. Clutch lever (page 3-8) 2. Left handlebar switches (page 3-7) 3. Starter (choke) lever (page 3-12) 4. Speedometer unit (page 3-6) 5. Fuel tank cap (page 3-9) 6. Right handlebar switches (page 3-7) 7. Throttle grip (page 6-13) 8. Brake lever (page 3-9) u5...
Page 17
Instrument and control functions 3 immobilizer system ........................................................................... 3-1 main switch/steering lock .................................................................. 3-2 indicator and warning lights ...........................................
Page 18
3-1 3 eau00027 3- instrument and control functions eau04992 immobilizer system this vehicle is equipped with an immo- bilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the fol- lowing. ● a code re-registering key (with a red bow) ● two standar...
Page 19
Instrument and control functions 3-2 3 ● do not place any key close to magnets (this includes, but not limited to, products such as speakers, etc.). ● do not place heavy items on any key. ● do not grind any key or alter its shape. ● do not disassemble the plastic part of any key. ● do not put two ke...
Page 20
Instrument and control functions 3-3 3 eau00040 lock the steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “off” po- sition, and then turn it to “lock” while still pushing...
Page 21
Instrument and control functions 3-4 3 eau03034 indicator and warning lights eau04877 oil level warning light “ ” this warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “on”. If the warning light does not come on...
Page 22
Instrument and control functions 3-5 3 eau04991* immobilizer system indicator light “ ” the electrical circuit of the indicator light can be checked by turning the key to “on”. If the indicator light does not come on for a few seconds, then go off, have a yamaha dealer check the electrical cir- cuit...
Page 23
Instrument and control functions 3-6 3 eau03193 speedometer unit the speedometer unit is equipped with a digital odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance trav- eled. The tripmeter shows the distance traveled since it was last set to zero. Pu...
Page 24
Instrument and control functions 3-7 3 eau00118 handlebar switches eau00119 pass switch “ ” press this switch to flash the headlight. Eau03888 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau00129 horn switch “ ” press this switch to sound the horn. Eau03...
Page 25
Instrument and control functions 3-8 3 eau03826 hazard switch “ ” with the key in the “on” or “ ” posi- tion, use this switch to turn on the haz- ard light (simultaneous flashing of all turn signal lights). The hazard light is used in case of an emergency or to warn other drivers when your motorcycl...
Page 26
Instrument and control functions 3-9 3 eau00158 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. Eau00162 brake pedal the brake pedal is on the right side of the motorcycle. To apply the rear brake, press down o...
Page 27
Instrument and control functions 3-10 3 2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover. Note: @ the fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and lo...
Page 28
Instrument and control functions 3-11 3 your yamaha engine has been de- signed to use regular unleaded gaso- line with a research octane number of 91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel will extend spark plug ...
Page 29
Instrument and control functions 3-12 3 res this indicates reserve. With the fuel cock lever in this position, the fuel re- serve is made available. Turn the fuel cock lever to this position if you run out of fuel while riding. When this occurs, refuel as soon as possible and be sure to turn the fue...
Page 30
Instrument and control functions 3-13 3 eau03202 seats passenger seat to remove the passenger seat remove the bolt, and then pull the pas- senger seat up. To install the passenger seat insert the projection on the front of the passenger seat into the holder as shown, place the seat in the original p...
Page 31
Instrument and control functions 3-14 3 to install the rider seat 1. Insert the projections on the front of the rider seat into the holders as shown, place the seat in the origi- nal position, and then install the bolt. 2. Install the passenger seat. Note: @ make sure that the seats are properly sec...
Page 32
Instrument and control functions 3-15 3 eau01869 storage compartment the storage compartment is located on the left side of the motorcycle. To open the storage compartment 1. Slide the lock cover open, insert the key into the lock, and then turn it clockwise. 2. Pull the storage compartment cov- er ...
Page 33
Instrument and control functions 3-16 3 to close the storage compartment 1. Place the storage compartment cover in its original position as shown. 2. Turn the key counterclockwise, re- move it, and then close the lock cover. Eau03194 adjusting the shock absorber assembly the shock absorber assembly ...
Page 34
Instrument and control functions 3-17 3 3. Pull the ignitor unit panel out to the right. 4. Remove the mudguard by remov- ing each quick fastener. 5. To increase the spring preload and thereby harden the suspen- sion, turn the adjusting ring in di- rection a. To decrease the spring preload and there...
Page 35
Instrument and control functions 3-18 3 ci-10e 6. Install the mudguard and ignitor unit panel by installing the quick fasteners. Note: @ to install a quick fastener, push the pin back so that it will protrude from the fastener head, and then insert the fas- tener and push the protruding pin in un- t...
Page 36
Instrument and control functions 3-19 3 eau00330 sidestand the sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the motorcycle upright. Note: @ the built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the...
Page 37
Instrument and control functions 3-20 3 cd-01e with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ ”. 3. Turn the key to “on”. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? The neutral sw...
Page 38
U5kse4.Book page 21 wednesday, september 11, 2002 11:55 am.
Page 39: Pre-Operation Checks
Pre-operation checks 4 pre-operation check list ..................................................................... 4-1 u5kse4.Book page 1 wednesday, september 11, 2002 11:55 am.
Page 40: Pre-Operation Checks
4-1 4 eau01114 4- pre-operation checks the condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire ai...
Page 41: Pre-Operation Checks
Pre-operation checks 4-2 4 throttle grip • make sure that operation is smooth. • check cable free play. • if necessary, have yamaha dealer adjust cable free play and lubricate cable and grip housing. 6-13 control cables • make sure that operation is smooth. • lubricate if necessary. 6-21 wheels and ...
Page 42: Pre-Operation Checks
Pre-operation checks 4-3 4 note: _ pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. _ ewa00033 warning _ if any item in the pre-operation check list...
Page 43
Operation and important riding points 5 starting a cold engine ....................................................................... 5-1 starting a warm engine ..................................................................... 5-3 shifting ..........................................................
Page 44
5-1 5 eau00372 5- operation and important riding points eau00373 warning @ ● become thoroughly familiar with all operating controls and their functions before riding. Consult a yamaha dealer re- garding any control or function that you do not thoroughly un- derstand. ● never start the engine or oper...
Page 45
Operation and important riding points 5-2 5 4. Turn the starter (choke) on and completely close the throttle. (see page 3-12 for starter (choke) oper- ation.) 5. Start the engine by pushing the start switch. Note: _ if the engine fails to start, release the start switch, wait a few seconds, and then...
Page 46
Operation and important riding points 5-3 5 eca00045 caution: _ for maximum engine life, never ac- celerate hard when the engine is cold! _ 7. When the engine is warm, turn the starter (choke) off. Note: _ the engine is warm when it responds normally to the throttle with the starter (choke) turned o...
Page 47
Operation and important riding points 5-4 5 ec000048 caution: @ ● even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running...
Page 48
Operation and important riding points 5-5 5 eau01128 engine break-in there is never a more important period in the life of your engine than the period between 0 and 1,600 km. For this rea- son, you should read the following ma- terial carefully. Since the engine is brand new, do not put an excessive...
Page 49
6 periodic maintenance and minor repair owner’s tool kit ....................................................6-1 periodic maintenance and lubrication chart .........6-2 removing and installing the panel .......................6-5 checking the spark plugs ....................................6-6 engin...
Page 50
6-1 6 eau00462 6- periodic maintenance and minor repair eau00464 safety is an obligation of the owner. Periodic inspection, adjustment and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. The most important points of in- spection, adjustment, and lubricatio...
Page 51
Periodic maintenance and minor repair 6-2 6 eau03685 periodic maintenance and lubrication chart note: _ ● the annual checks must be performed every year, except if a kilometer-based maintenance is performed instead. ● from 50,000 km, repeat the maintenance intervals starting from 10,000 km. ● items ...
Page 52
Periodic maintenance and minor repair 6-3 6 8 * rear brake • check operation, fluid level and vehicle for fluid leakage. (see note on page 6-4.) √ √ √ √ √ √ • replace brake pads. Whenever worn to the limit 9 * brake hoses • check for cracks or damage. √ √ √ √ √ • replace. (see note on page 6-4.) eve...
Page 53
Periodic maintenance and minor repair 6-4 6 eau03884 note: _ ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal components...
Page 54
Periodic maintenance and minor repair 6-5 6 eau01777 removing and installing the panel the panel shown above needs to be removed to perform some of the main- tenance jobs described in this chapter. Refer to this section each time the pan- el needs to be removed and installed. Eau00491 panel a to rem...
Page 55
Periodic maintenance and minor repair 6-6 6 eau01673 checking the spark plugs the spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic mai...
Page 56
Periodic maintenance and minor repair 6-7 6 to install a spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if nec- essary, adjust the gap to specifica- tion. 2. Clean the surface of the spark plug gasket and its mating sur- face, and then wipe off any grime from the spark plu...
Page 57
Periodic maintenance and minor repair 6-8 6 3. Wait a few minutes until the oil set- tles, and then check the oil level through the check window located at the bottom-left side of the crank- case. Note: _ the engine oil should be between the minimum and maximum level marks. _ 4. If the engine oil is...
Page 58
Periodic maintenance and minor repair 6-9 6 eca00133 caution: _ ● in order to prevent clutch slip- page (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel speci- fication of “cd” or oils of a higher quality than specified. In addition,...
Page 59
Periodic maintenance and minor repair 6-10 6 to check the final gear oil level 1. Place the motorcycle on a level surface and hold it in an upright position. Note: _ ● the final gear oil level must be checked on a cold engine. ● make sure that the motorcycle is positioned straight up when check- ing...
Page 60
Periodic maintenance and minor repair 6-11 6 eau03195* cleaning the air filter element the air filter element should be cleaned as follows at the intervals specified in the periodic maintenance and lubrica- tion chart. Clean the air filter element more frequently if you are riding in un- usually wet...
Page 61
Periodic maintenance and minor repair 6-12 6 eau00630 adjusting the carburetors the carburetors are important parts of the engine and require very sophisti- cated adjustment. Therefore, most car- buretor adjustments should be left to a yamaha dealer, who has the neces- sary professional knowledge an...
Page 62
Periodic maintenance and minor repair 6-13 6 eau00635 adjusting the throttle cable free play the throttle cable free play should measure 4–6 mm at the throttle grip. Periodically check the throttle cable free play and, if necessary, have a yamaha dealer adjust it. Eau00637 adjusting the valve cleara...
Page 63
Periodic maintenance and minor repair 6-14 6 ce-21e ce-07e ewa00012 warning _ because loading has an enormous impact on the handling, braking, performance and safety characteris- tics of your motorcycle, you should keep the following precautions in mind. ● never overload the motorcycle! Operation of...
Page 64
Periodic maintenance and minor repair 6-15 6 tire inspection the tires must be checked before each ride. If the center tread depth reaches the specified limit, if the tire has a nail or glass fragments in it, or if the side- wall is cracked, have a yamaha dealer replace the tire immediately. Ce-08e ...
Page 65
Periodic maintenance and minor repair 6-16 6 eau00685 spoke wheels to maximize the performance, durabil- ity, and safe operation of your motor- cycle, note the following points regarding the specified wheels. ● the wheel rims should be checked for cracks, bends or warpage, and the spokes for loosene...
Page 66
Periodic maintenance and minor repair 6-17 6 eau00696 adjusting the brake lever free play the brake lever free play should mea- sure 5–8 mm as shown. Periodically check the brake lever free play and, if necessary, adjust it as follows. 1. Loosen the locknut at the brake le- ver. 2. To increase the b...
Page 67
Periodic maintenance and minor repair 6-18 6 eau01746 adjusting the brake pedal position the top of the brake pedal should be positioned approximately 98.5 mm above the top of the footrest as shown. Periodically check the brake pedal po- sition and, if necessary, have a yamaha dealer adjust it. Ew00...
Page 68
Periodic maintenance and minor repair 6-19 6 eau01314 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Each brake pad is provided with a wear indicator groove, which allows yo...
Page 69
Periodic maintenance and minor repair 6-20 6 observe these precautions: ● when checking the fluid level, make sure that the top of the brake fluid reservoir is level. ● use only the recommended quali- ty brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking perfor...
Page 70
Periodic maintenance and minor repair 6-21 6 eau02962 checking and lubricating the cables the operation of all control cables and the condition of the cables should be checked before each ride, and the ca- bles and cable ends should be lubricat- ed if necessary. If a cable is damaged or does not mov...
Page 71
Periodic maintenance and minor repair 6-22 6 eau03164 checking and lubricating the brake and clutch levers the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Eau03165 checking and lubricating the sidestand the op...
Page 72
Periodic maintenance and minor repair 6-23 6 eau02939 checking the front fork the condition and operation of the front fork must be checked as follows at the intervals specified in the periodic main- tenance and lubrication chart. To check the condition ew000115 warning @ securely support the motorc...
Page 73
Periodic maintenance and minor repair 6-24 6 2. Hold the lower ends of the front fork legs and try to move them for- ward and backward. If any free play can be felt, have a yamaha dealer check or repair the steer- ing. Eau01144 checking the wheel bearings the front and rear wheel bearings must be ch...
Page 74
Periodic maintenance and minor repair 6-25 6 eau04242 battery the battery is located behind panel a. (see page 6-5 for panel removal and installation procedures.) this motorcycle is equipped with a sealed-type (mf) battery, which does not require any maintenance. There is no need to check the electr...
Page 75
Periodic maintenance and minor repair 6-26 6 to charge the battery have a yamaha dealer charge the bat- tery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the motorcycle is equipped with op- tional electrical accessories. To stor...
Page 76
Periodic maintenance and minor repair 6-27 6 eau04993 replacing the fuses the main fuse is located under the igni- tor unit panel. The fuse box, which contains the fuses for the individual circuits, is located in- side the storage compartment. (see page 3-15 for storage compartment cover removal and...
Page 77
Periodic maintenance and minor repair 6-28 6 3. Pull the ignitor unit panel outward to the right. 4. Turn the key to “off” and turn off the electrical circuit in question. 5. Remove the blown fuse, and then install a new fuse of the specified amperage. Ec000103 caution: _ do not use a fuse of a high...
Page 78
Periodic maintenance and minor repair 6-29 6 9. Place the ignitor unit panel in the original position and install the quick fasteners. Note: _ to install a quick fastener, push its pin back so that it will protrude from the fastener head, then insert the fastener and push the protruding pin in until...
Page 79
Periodic maintenance and minor repair 6-30 6 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. Ew000119 warning _ headlight bulbs get very hot. There- fore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until i...
Page 80
Periodic maintenance and minor repair 6-31 6 eau00855 replacing a turn signal light bulb or the tail/brake light bulb 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 3. Insert a new bulb into the socket, push it in, and then...
Page 81
Periodic maintenance and minor repair 6-32 6 to service the rear wheel raise the rear wheel off the ground by using a motorcycle stand or, if a motor- cycle stand is not available, by placing a jack either under each side of the frame in front of the rear wheel or under each side of the swingarm. Ea...
Page 82
Periodic maintenance and minor repair 6-33 6 eau01297 troubleshooting chart ew000125 warning @ keep away open flames and do not smoke while checking or working on the fuel system. @ check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply f...
Page 83: Motorcycle Care and Storage
Motorcycle care and storage 7 care .................................................................................................. 7-1 storage .............................................................................................. 7-4 u5kse4.Book page 1 wednesday, september 11, 2002 11:55 ...
Page 84: Motorcycle Care and Storage
7-1 7 eau03412 7- motorcycle care and storage care while the open design of a motorcycle reveals the attractiveness of the tech- nology, it also makes it more vulnera- ble. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go un- noticed on a car, howe...
Page 85: Motorcycle Care and Storage
Motorcycle care and storage 7-2 7 thinner, fuel (gasoline), rust re- movers or inhibitors, brake flu- id, antifreeze or electrolyte. ● do not use high-pressure wash- ers or steam-jet cleaners since they cause water seepage and deterioration in the following ar- eas: seals (of wheel and swing- arm be...
Page 86: Motorcycle Care and Storage
Motorcycle care and storage 7-3 7 1. Clean the motorcycle with cold water and a mild detergent, after the engine has cooled down. Eca00012 caution: _ do not use warm water since it in- creases the corrosive action of the salt. _ 2. After drying the motorcycle, apply a corrosion protection spray on a...
Page 87: Motorcycle Care and Storage
Motorcycle care and storage 7-4 7 eca00013 caution: _ ● apply spray oil and wax spar- ingly and make sure to wipe off any excess. ● never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product. ● avoid using abrasive polishing compounds as they will wear away t...
Page 88: Motorcycle Care and Storage
Motorcycle care and storage 7-5 7 c. Install the spark plug caps onto the spark plugs, and then place the spark plugs on the cylinder head so that the electrodes are grounded. (this will limit spark- ing during the next step.) d. Turn the engine over several times with the starter. (this will coat t...
Page 89: Specifications
Specifications 8 specifications .................................................................................... 8-1 conversion table ............................................................................... 8-5 u5kse4.Book page 1 wednesday, september 11, 2002 11:55 am.
Page 90: Specifications
8-1 8 eau01038 8- specifications specifications cs-01e model xvs1100a dimensions overall length 2,465 mm overall width 945 mm overall height 1,095 mm seat height 710 mm wheelbase 1,645 mm ground clearance 145 mm minimum turning radius 3,300 mm basic weight (with oil and full fuel tank) 291 kg engine...
Page 91: Specifications
Specifications 8-2 8 final gear oil type hypoid gear oil sae 80 (api gl4) or multi-grade hypoid gear oil sae 80w-90 quantity 0.2 l air filter dry type element fuel type regular unleaded gasoline only fuel tank capacity 17 l fuel reserve amount 4.5 l carburetor manufacturer mikuni model × quantity bs...
Page 92: Specifications
Specifications 8-3 8 tire air pressure (measured on cold tires) up to 90 kg* front 225 kpa (2.25 kgf/cm 2 , 2.25 bar) rear 225 kpa (2.25 kgf/cm 2 , 2.25 bar) 90 kg–maximum* front 225 kpa (2.25 kgf/cm 2 , 2.25 bar) rear 250 kpa (2.50 kgf/cm 2 , 2.50 bar) * total weight of rider, passenger, cargo and ...
Page 93: Specifications
Specifications 8-4 8 bulb voltage, wattage × quantity headlight 12 v, 60/55 w × 1 auxiliary light 12 v, 4 w × 1 tail/brake light 12 v, 5/21 w × 1 turn signal light 12 v, 21 w × 4 meter lighting 14 v, 1.4 w × 2 oil level warning light 12 v, 1.7 w × 1 neutral indicator light 12 v, 1.7 w × 1 turn signa...
Page 94: Specifications
Specifications 8-5 8 eau04513 conversion table cs-04e all specification data in this manual are listed in si and metric units. Use this table to convert metric unit values to imperial unit values. Example: metric value conversion factor imperial value 2 mm × 0.03937 = 0.08 in conversion table metric...
Page 95: Consumer Information
Consumer information 9 identification numbers ....................................................................... 9-1 key identification number .................................................................. 9-1 vehicle identification number ......................................................
Page 96: Consumer Information
9-1 9 eau01039 9- consumer information eau02944 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle...
Page 97: Consumer Information
Consumer information 9-2 9 eau01804 model label the model label is affixed to the frame under the rider seat. (see page 3-13 for rider seat removal and installation pro- cedures.) record the information on this label in the space provided. This in- formation will be needed when ordering spare parts ...
Page 98: Index
10- index a air filter element, cleaning ......................6-11 anti-theft alarm (optional) .........................3-6 b battery ...................................................6-25 brake and clutch levers, checking and lubricating ......................6-22 brake and shift pedals, checking...
Page 99: Index
Index storage.................................................... 7-4 storage compartment ............................ 3-15 supporting the motorcycle ..................... 6-31 t throttle cable free play, adjusting .......... 6-13 throttle grip and cable, checking and lubricating ......................
Page 100
Shiro.Fm page 1 thursday, june 7, 2001 11:38 am.
Page 101
Shiro.Fm page 1 thursday, june 7, 2001 11:38 am.
Page 102: 5Ks-28199-E4
Printed on recycled paper yamaha motor co., ltd. Printed in japan 2002.09-0.3 ×1 cr (e) 5ks-28199-e4 xvs1100a owner’s manual.