1. DL manuals
  2. Yamaha
  3. Outboard Motor
  4. F2.5C
  5. Owner's Manual

Yamaha F2.5C Owner's Manual

Other manuals for F2.5C: Owner's Manual, Owner's Manual
Manual is about: Outboard Motor F25C; T25C

Summary of F2.5C

  • Page 1

    Owner’s manual f2.5c lit-18626-05-28 u.S.A.Edition.

  • Page 3: To The Owner

    E emu01448 to the owner thank you for choosing a yamaha outboard motor. This owner’s manual contains infor- mation needed for proper operation, mainte- nance and care. A thorough understanding of these simple instructions will help you obtain maximum enjoyment from your new yamaha. If you have any q...

  • Page 4: Contents

    E emu00003 contents read this owner’s manual carefully before operating your outboard motor. General information 1 basic components 2 operation 3 maintenance 4 trouble recovery 5 index 6 u69m11.Book page 1 thursday, january 30, 2003 1:04 pm.

  • Page 5: Chapter 1

    E 1 emu00004 chapter 1 general information identification numbers record .....................................................1-1 outboard motor serial number ................1-1 emission control information ....1-2 north american models............................1-2 star labels.......................

  • Page 6: Identification Numbers

    1-1 e emu00005 identification numbers record emu00007 outboard motor serial number the outboard motor serial number is stamped on the label attached to the port side of the clamp-bracket. Record your outboard motor serial number in the spaces provided to assist you in ordering spare parts from your ...

  • Page 7: Emission Control

    1-2 e 1 2 emu01385 emission control information emu01444¯ north american models this engine conforms to u.S. Environmental protection agency (epa) regulations for marine si engines. See the label affixed to your engine for details. Approval label of emission control certif- icate this label is attac...

  • Page 8

    1-3 e emu01389 star labels your outboard motor is labeled with a cali- fornia air resources board (carb) star label. See below for a description of your particular label. 1 star label one star - low emission the one-star label identifies engines that meet the air resources board’s 2001 exhaust emiss...

  • Page 9: Safety

    1-4 e emu00917 safety information ● before mounting or operating the out- board motor, read this entire manual. Reading it should give you an under- standing of the motor and its operation. ● before operating the boat, read any owner’s or operator’s manuals supplied with it and all labels. Be sure y...

  • Page 10

    1-5 e ● when a swimmer is in the water near you shift into neutral and shut off the engine. ● be informed about boating safety. Addi- tional publications and information can be obtained from many organizations, includ- ing the following: united states coast guard consumer affairs staff (g-bc) office...

  • Page 11: Important Labels

    1-6 e 1 2 emu00014 important labels warning labels u69m11.Book page 6 thursday, january 30, 2003 1:04 pm.

  • Page 12

    1-7 e 3 caution labels u69m11.Book page 7 thursday, january 30, 2003 1:04 pm.

  • Page 13: Basic Boating Rules

    1-8 e emu00015 basic boating rules (rules of the road) just as there are rules which apply when you are driving on streets and high ways, there are waterway rules which apply when you are driving your boat. These rules are used internationally, and are also enforced by the united states coast guard ...

  • Page 14

    1-9 e rules when encountering vessels there are three main situations which you may encounter with other vessels which could lead to a collision unless the steering rules are followed: meeting (you are approaching another vessel head-on) crossing (you are traveling across the other ves- sel’s path) ...

  • Page 15

    1-10 e other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you. Other special situations there are ...

  • Page 16

    1-11 e remember, markings may vary by geo- graphic location. Always consult local boat- ing authorities before driving your boat in unfamiliar waters. U69m11.Book page 11 thursday, january 30, 2003 1:04 pm.

  • Page 17: Fueling Instructions

    1-12 e emu00016¯ fueling instructions warning @ gasoline and its vapors are highly flammable and explosive! ● do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. ● stop engine before refueling. ● refuel in a well-ventilated area. ● take care not to spill gas...

  • Page 18

    1-13 e emu18040 gasoline if knocking or pinging occurs, use a different brand of gasoline or premium unleaded fuel. Emu00027 gasohol there are two types of gasohol: gasohol containing ethanol and that containing meth- anol. Gasohol containing ethanol can be used if ethanol content does not exceed 10...

  • Page 19: Engine Oil

    1-14 e emu17690 engine oil recommended engine oil: 4-stroke motor oil with a combination of cor- responding sae and api as shown in the chart. Engine oil quantity: see chapter 4, “specifications.” caution: @ all 4-stroke engines are shipped from the factory without engine oil. @ u69m11.Book page 14 ...

  • Page 20: Propeller Selection

    1-15 e emu01395 propeller selection the performance of your outboard motor will be critically affected by your choice of pro- peller, as an incorrect choice could adversely affect performance and could also seriously damage the motor. Engine speed depends on the propeller size and boat load. If engi...

  • Page 21

    1-16 e note: @ at full throttle and under a maximum boat load, the engine’s rpm should be within the upper half of the full throttle operating range, as listed in “specifications” on page 4-1. Select a propeller which fulfills this require- ment. If operating under conditions which allow the engine’...

  • Page 22: -Memo-

    1-17 e -memo- u69m11.Book page 17 thursday, january 30, 2003 1:04 pm.

  • Page 23: Chapter 2

    2 e emu00037 chapter 2 basic components main components ................................2-1 operations of controls and other functions..................................2-2 fuel tank...................................................2-2 fuel cock ..................................................2-3 ...

  • Page 24: Main Components

    2-1 e emu01206¯ main components 1 top cowling 2 top cowling lock levers 3 carrying handle 4 steering friction adjusting screw 5 anti-cavitation plate 6 propeller 7 cooling water inlet 8 trim angle adjusting rod 9 clamp bracket 0 tiller handle a air vent screw b fuel tank cap c recoil starter handle ...

  • Page 25: Operations of Controls

    2-2 e emu00039 operations of controls and other functions emu01729¯ fuel tank if your model included a fuel tank, its parts and functions are as follows. 1 fuel tank cap 2 air vent screw emu00045 fuel tank cap this cap is for filling fuel. To remove it, turn it counterclockwise. Emu00046 air vent sc...

  • Page 26

    2-3 e emu00846 fuel cock the fuel cock 1 is to supply or stop fuel from the fuel tank to the engine. Emu01731 close with the lever/knob in the position a, fuel does not flow. Always turn the knob to this position when the engine is not running. Emu01732 open with the lever/knob in this position b, f...

  • Page 27

    2-4 e emu00057¯ choke knob pulling out this knob (setting it to on) sup- plies a rich mixture required to start the engine. Emu00059 recoil starter handle (if equipped) pull the handle gently until resistance is felt. Then vigorously pull the handle straight out to crank the engine to start it. Emu0...

  • Page 28: Warning

    2-5 e emu00065 throttle control grip the throttle control grip is on the tiller han- dle. Turn the grip counterclockwise to increase speed and clockwise to decrease speed. Emu00067 throttle indicator the fuel consumption curve on the throttle indicator shows the relative amount of fuel consumed for ...

  • Page 29: Warning

    2-6 e emu00932 engine stop lanyard switch the lock-plate 1 must be attached to the engine stop lanyard switch for the engine to run. The lanyard 2 should be attached to a secure place on the operator’s clothing, or arm or leg. Should the operator fall over- board or leave the helm, the lanyard will ...

  • Page 30: Warning

    2-7 e emu00108 steering friction adjusting screw (for tiller control model) a friction device provides resistance to steering movement. This is adjustable for operator preference. An adjusting screw/bolt is located on the swivel bracket. Emu01296 adjustment warning @ do not over tighten the friction...

  • Page 31

    2-8 e emu00892 top cowling lock lever to remove the engine top cowling, pull up the lock lever(s). Then, lift off the cowling. When replacing the cowling, check to be sure it fits properly. Then, lock the cowling again by moving the lever downward. Emu01240 carrying handle a carrying handle is provi...

  • Page 32: -Memo-

    2-9 e -memo- u69m11.Book page 9 thursday, january 30, 2003 1:04 pm.

  • Page 33: Chapter 3

    E 3 emu00174 chapter 3 operation installation ..........................................3-1 mounting the outboard motor ..................3-2 clamping the outboard motor..................3-4 pre-operation checks .....................3-5 checking the engine oil level...................3-6 filling fue...

  • Page 34: Installation

    3-1 e emu00175 installation caution: @ incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat or accessories such as transom ladders/depth finder transducers) can create airborne water spray while the boat is cruising. Severe engine damage may resul...

  • Page 35: Warning

    3-2 e emu01478¯ mounting the outboard motor warning @ ● overpowering a boat may cause severe instability. Do not install an out- board motor with more horsepower than the maximum rating on the capac- ity plate of the boat. If the boat does not have a capacity plate, consult the boat manufacturer. ● ...

  • Page 36

    3-3 e emu01298 mounting height to run your boat at optimum efficiency, the water-resistance (drag) of the boat and out- board motor must be made as little as possi- ble. The mounting-height of the outboard motor greatly affects the water-resistance. If the mounting-height is too high, cavitation ten...

  • Page 37: Warning

    3-4 e emu00183 clamping the outboard motor 1) place the outboard on the transom so that it is positioned as close to the cen- ter as possible. Tighten the transom clamp screws evenly and securely. Check the clamp-screws for tightness occasionally during operation of the motor as they can work loose ...

  • Page 38: Pre-Operation Checks

    3-5 e emu00204 pre-operation checks warning @ if any item in the pre-operation check is not working properly, have it inspected and repaired before operating the out- board motor. Otherwise, an accident could occur. @ caution: @ do not start the engine out of water. Overheating and serious engine da...

  • Page 39

    3-6 e emu00209 controls ● check throttle, shift, and steering for proper operation before starting the engine. ● the controls should work smoothly, with- out binding or unusual free play. ● look for loose or damaged connections. ● check operation of the starter and stop switches when the outboard mo...

  • Page 40: Filling Fuel

    3-7 e emu00202 filling fuel 1) remove the fuel tank cap. 2) fill the fuel tank carefully. 3) close the cap securely after refueling. Wipe up any spilled fuel. Fuel tank capacity: refer to specifications, page 4-1. Emu00203 ring free fuel additive gasoline is a precise blend of many different substan...

  • Page 41: Breaking In (Running In)

    3-8 e emu00224 breaking in (running in) engine your new engine requires a period of break- in (running-in) to allow mating surfaces of moving parts to wear-in evenly. Correct break-in (running-in) will help ensure proper performance and longer engine life. Caution: @ failure to follow the break-in (...

  • Page 42: Starting Engine

    3-9 e emu01734 starting engine warning @ ● before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstruc- tions. Be sure there are no swimmers in the water near you. ● when the air vent screw is loosened, gasoline (petrol) vapor will be released. G...

  • Page 43: Warning

    3-10 e eemu01735 procedure for tiller control model 3) place the gear-shift lever in the neutral position. Warning @ always start the engine in neutral to avoid accidentally moving the boat. @ 4) attach the engine stop switch lanyard to a secure place on your clothing, or your arm or leg. Then, inst...

  • Page 44

    3-11 e emu01514* manual start models 6) pull out the choke knob completely. Note: @ it is not necessary to use the choke when restarting a warm engine. @ 7) pull the starter handle slowly until you feel resistance. Then give a strong pull straight out to crank and start the engine. Repeat if necessa...

  • Page 45: Warming Up Engine

    3-12 e emu01368¯ warming up engine 1) after the engine starts, return the choke knob to the half-way position. For approximately the first 5 minutes after starting, warm up the engine by operat- ing at one fifth throttle or less. After the engine has warmed up, completely push in the choke knob. (fa...

  • Page 46: Shifting

    3-13 e emu00261 shifting warning @ before shifting, make sure there are no swimmers or obstacles in the water near you. @ caution: @ to change the shifting position from for- ward to reverse or vice-versa, close the throttle first so that the engine idles (or runs at low speeds). @ emu00263 forward ...

  • Page 47: Stopping Engine

    3-14 e emu00273¯ stopping engine emu01737 1) place the throttle control grip in the fully closed position. 2) place the gear-shift lever in the neutral position. 3) push and hold the engine stop button until the engine comes to a complete stop. 4) after stopping the engine, set the fuel cock to the ...

  • Page 48: Trimming Outboard

    3-15 e emu01412 trimming outboard motor the trim angle of the outboard motor helps determine the position of the bow of the boat in the water. The correct trim angle will help improve performance and fuel economy while reducing strain on the engine. The cor- rect trim angle depends upon the combina-...

  • Page 49: Warning

    3-16 e adjusting trim angle emu01738 manual tilt model there are 4 holes provided in the clamp bracket to adjust the outboard motor trim angle. 1) stop the engine. 2) loosen the trim angle adjusting rod nut, and then remove the trim angle adjust- ing rod 1 while tilting the motor up. 3) reposition t...

  • Page 50

    3-17 e emu19160¯ trim angle settings and boat handling when the boat is on plane, a bow-up atti- tude results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees. With the bow up, the boat may have a greater tendency to steer to...

  • Page 51: Tilting Up/down

    3-18 e emu01739 tilting up/down if the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the pro- peller and casing from damage by collision with obstructions, and also to reduce salt corrosion. Caution: @ ● before tilting the motor...

  • Page 52

    3-19 e emu01740 procedure for tilting up 1) tighten the air vent screw(s). 2) place the fuel cock in the closed posi- tion. 3) place the gear shift lever in neutral and face the motor forward. 4) hold the rear handle and tilt the engine up fully until the tilt support lever auto- matically turns to ...

  • Page 53: Chapter 4

    E 4 emu00317 chapter 4 maintenance specifications ......................................4-1 transporting and storing outboard motor.................................4-2 trailering outboard motor ........................4-2 transporting outboard when unmounted ............................................

  • Page 54: Specifications

    4-1 e emu18700¯ specifications model item unit f2.5mhc dimensions overall length mm (in.) 623 (24.5) overall width mm (in.) 345 (13.6) overall height s mm (in.) 1,021 (40.2) transom height s mm (in.) 432 (17.0) weight s kg (lb.) 17.0 (37.5) performance full throttle operating range r/min 5,250–5,750...

  • Page 55: Transporting and

    4-2 e emu01369 transporting and storing outboard motor warning @ leaking fuel is a fire hazard. When trans- porting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking. @ emu00326¯ trailering outboard motor the motor should be trailered and stored in t...

  • Page 56: Caution:

    4-3 e 1 2 3 emu01362 transporting outboard when unmounted transport in an upright position to prevent engine oil from entering the cylinder head and causing damage to the motor. Emu00330 storing outboard motor when storing your yamaha outboard for pro- longed periods of time, (2 months or longer), s...

  • Page 57

    4-4 e emu00335 filling fuel tank fill the fuel tank with fresh fuel and add one ounce of “yamaha fuel conditioner and sta- bilizer” (part no. Lub-fuelc-12-00) to each gallon of fuel. Note: @ the use of “yamaha fuel conditioner and stabilizer” eliminates the need to drain the fuel system. Consult you...

  • Page 58: Warning

    4-5 e emu00338 flushing cooling system and fogging engine cooling system flushing is essential to pre- vent the cooling system from clogging up with salt, sand, or dirt. In addition, fogging of the engine is mandatory to prevent expen- sive engine damage due to rust. Perform the flushing and fogging...

  • Page 59

    4-6 e emu00349 lubrication 1) remove the spark plug(s). Spray a yamaha “stor-rite engine fogging oil” into each cylinder for 10 seconds. Grease the spark plug threads and rein- stall the spark plug(s) and torque to proper specification. (refer to the “cleaning and adjusting spark plug”). 2) turn the...

  • Page 60: Periodic Maintenance

    4-7 e emu01569 periodic maintenance warning @ be sure to turn off the engine when you perform maintenance unless otherwise specified. If the owner is not familiar with machine servicing, this work should be done by a yamaha dealer or other quali- fied mechanic. @ maintenance, replacement, or repair ...

  • Page 61

    4-8 e emu19310 maintenance chart frequency of maintenance operations may be adjusted according to the operating condi- tions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action. The mark ( ●) indicates the check-ups ...

  • Page 62

    4-9 e emu00366 greasing yamaha marine grease (water resistant grease) u69m11.Book page 9 thursday, january 30, 2003 1:04 pm.

  • Page 63: Warning

    4-10 e emu01202 cleaning and adjusting spark plug warning @ when removing or installing a spark plug, be careful not to damage the insu- lator. A damaged insulator could allow external sparks, which could lead to explosion or fire. @ the spark plug is an important engine com- ponent and is easy to i...

  • Page 64

    4-11 e when fitting the plug, always clean the gas- ket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque. Note: @ if a torque-wrench is not available when you are fitting a spark plug, a good estimate of the correct torque is 1/4 to 1...

  • Page 65: Warning

    4-12 e emu01509¯ checking fuel system warning @ gasoline (petrol) and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames or other sources of ignition. @ check the fuel line for leaks, cracks, or mal- functions. If any problem is found, it should be repaired imme...

  • Page 66: Warning

    4-13 e emu09912 inspecting idling speed warning @ ● do not touch or remove electrical parts when starting or during operation. ● keep hands, hair and clothes away from flywheel and other rotating parts while engine is running. @ caution: @ this procedure must be performed while the outboard motor is...

  • Page 67: Warning

    4-14 e emu01742 changing engine oil warning @ ● avoid draining the engine oil immedi- ately after stopping the engine. The oil is hot and should be handled with care to avoid burns. ● be sure the outboard is securely fas- tened to the transom or a stable stand. @ caution: @ ● change the engine oil a...

  • Page 68

    4-15 e note: @ if a torque wrench is not available when you are installing the drain plug, finger tighten the bolt just until the gasket comes into con- tact with the surface of the drain hole. Then tighten 1/4 - 1/2 turn. Have the drain plug torqued to the correct value with a torque wrench as soon...

  • Page 69

    4-16 e emu00383 checking wiring and connectors 1) check that each grounding wire is prop- erly secured. 2) check that each connector is engaged securely. Emu00384 exhaust leakage start the engine and check that no exhaust leaks from the joints between the exhaust cover, cylinder head and crank case....

  • Page 70: Warning

    4-17 e emu01743 checking propeller warning @ you could be seriously injured if the engine accidentally starts while you are near the propeller. ● before inspecting, removing or install- ing the propeller, remove the spark plug cap from the spark plug. Also, put the shift control in neutral and remov...

  • Page 71: Caution:

    4-18 e emu00926 installing the propeller caution: @ ● be sure to install the thrust washer before installing propeller, otherwise, lower case and propeller boss may be damaged. ● be sure to use a new cotter pin and bend the ends over securely. Other- wise, the propeller could come off dur- ing opera...

  • Page 72: Warning

    4-19 e emu01460¯ changing gear oil warning @ ● be sure the outboard is securely fas- tened to the transom or a stable stand. You could be severely injured if the outboard falls on you. ● never get under the lower unit while it is tilted, even when the tilt-support lever/knob is locked. Severe injury...

  • Page 73: Caution:

    4-20 e emu14622 inspecting and replacing anode(s) yamaha outboard motors are protected from corrosion by sacrificial anodes. Inspect the external anodes periodically. Remove scales from the surfaces of the anodes. Consult a yamaha dealer for replacement of external anodes. Caution: @ do not paint an...

  • Page 74

    4-21 e emu00409 motor exterior emu00410 cleaning the outboard motor after use, wash the exterior of the outboard with fresh water. Flush the cooling system with fresh water. Note: @ refer to flushing cooling system instruc- tions in “transporting and storing outboard motor”. @ emu00412 checking pain...

  • Page 75: Chapter 5

    E 5 emu00414 chapter 5 trouble recovery troubleshooting ...............................5-1 temporary action in emergency .............................................5-4 impact damage ........................................5-4 starter will not operate .............................5-5 treatment of s...

  • Page 76: Troubleshooting

    5-1 e emu01752¯ troubleshooting a problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. The troubleshooting chart describes basic checks and possible remedies. (this chart covers all yamaha outboard motors. Therefore, some items may not appl...

  • Page 77

    5-2 e c. Engine idles irregularly or stalls. 1. Spark plug(s) fouled or incorrect type. 1. Inspect spark plug(s). Clean or replace with recommended type. 2. Fuel system obstructed. 2. Check for pinched or kinked fuel line or other obstructions in fuel system. 3. Fuel contaminated or stale. 3. Fill t...

  • Page 78

    5-3 e d. Engine power loss. 1. Propeller damaged. 1. Have propeller repaired or replaced. 2. Propeller pitch or diameter incorrect. 2. Install correct propeller to operate out- board at its recommended speed (r/min) range. 3. Trim angle incorrect. 3. Adjust trim angle to achieve most effi- cient ope...

  • Page 79: Temporary Action In

    5-4 e emu00416 temporary action in emergency emu01492 impact damage warning @ the outboard motor can be seriously damaged by a collision while operating or trailering. Damage could make the outboard motor unsafe to operate. @ if the outboard motor hits any object in the water, follow the procedure b...

  • Page 80: Warning

    5-5 e emu01744 starter will not operate if the starter mechanism does not operate, the engine can be started with an emer- gency starter rope. Warning @ ● use this procedure only in an emer- gency and only to return to port for repairs. ● when the emergency starter rope is used to start the engine t...

  • Page 81

    5-6 e emu01746 emergency starting engine 1) remove the top cowling. 2) remove the bolts 1 from the fuel tank. 3) remove the bolts 2 from the starter case. 4) while lifting the fuel tank up, remove the bolt 3 from the starter case. 5) remove the collar 4. 6) while lifting the starter case up, discon-...

  • Page 82

    5-7 e 8) install the fuel tank bracket by installing the bolts 2. 9) install 2 bolts 1 into the rear section of the fuel tank. 10) prepare the engine for starting. See “starting engine” for procedures. Be sure the engine is in neutral and that the lanyard lock plate is attached to the engine stop la...

  • Page 83: Caution:

    5-8 e emu01511 treatment of submerged motor if the outboard motor is submerged, immedi- ately take it a yamaha dealer. Otherwise, some corrosion may begin almost immedi- ately. If you cannot immediately take the outboard motor to a yamaha dealer, follow the proce- dure below in order to minimize eng...

  • Page 84: -Memo-

    5-9 e -memo- u69m11.Book page 9 thursday, january 30, 2003 1:04 pm.

  • Page 85: Chapter 6

    E 6 emu00450 chapter 6 index index ..........................................................6-1 u69m11.Book page 1 thursday, january 30, 2003 1:04 pm.

  • Page 86: Index

    6-1 e emu00451 index a adjusting trim angle ....................................... 3-16 adjustment....................................................... 2-7 air vent screw .................................................. 2-2 approval label of emission control certificate... 1-2 b basic boating r...

  • Page 87

    6-2 e p periodic maintenance ...................................... 4-7 pre-operation checks....................................... 3-5 procedure for tiller control model................... 3-10 procedure for tilting down .............................. 3-19 procedure for tilting up.....................

  • Page 88: Canada

    Emu01599 important warranty information for u.S.A. And canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is com- mitted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying one. Please read the follo...

  • Page 89

    5. Your warranty applies specifically to repairs made in the country of purchase. If your u.S.-purchased yamaha needs warranty service while in canada, or your canadian purchased yamaha needs service while in the united states, yamaha will assist the local dealer whenever possible. However, some pro...

  • Page 90

    Emu01404 yamaha motor corporation, u.S.A. Four-stroke outboard motor three-year limited warranty yamaha motor corporation, u.S.A. Hereby warrants that new yamaha 1999-or-later model four-stroke outboard motors originally distrib- uted by yamaha motor corporation, u.S.A. Will be free from defects in ...

  • Page 91

    Specific parts excluded from warranty. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, shear pins, propellers, hubs, fuel and oil filters, brushes for the starter motor and power tilt motor, water pump impellers, and anodes, are not covered by warranty. Charges for...

  • Page 92

    Emu01178 important warranty information if you use your yamaha outside u.S.A. Or canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is com- mitted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying ...

  • Page 93

    January 2003–0.3 × 1 cr printed in france 69m-f8199-11 (f2.5amh) (e) yamaha motor corporation, usa.

  • Page 94

    Warranty card 12/6/01 7:40 pm page 1.

  • Page 95

    Warranty card 12/6/01 7:40 pm page 2.