1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. FJR1300AS
  5. Owner's Manual

Yamaha FJR1300AS Owner's Manual

Summary of FJR1300AS

  • Page 1

    Dic183 fjr1300as owner’s manual read this manual carefully before operating this vehicle. 1md-28199-e0 [english (e)].

  • Page 2

    Eau50920 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. General manager of quality assurance div. Date of issue: 1 aug. 2002 place of issue: shizuoka, japan declaration of conformity yamaha motor electronics co., ltd. 1450-6, mori, ...

  • Page 3: Introduction

    Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the fjr1300as, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take...

  • Page 4: Important Manual Information

    Important manual information eau10133 particularly important information is distinguished in this manual by the following notations: *product and specifications are subject to change without notice. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey a...

  • Page 5: Important Manual Information

    Important manual information eau10200 fjr1300as owner’s manual ©2012 by yamaha motor co., ltd. 1st edition, december 2012 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U1mde0e0.Book page 2 f...

  • Page 6: Table Of Contents

    Table of contents safety information ..................1-1 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments.................2-3 instrument and control functions .....

  • Page 7: Table of Contents

    Table of contents checking and lubricating the brake lever ..........................................6-27 checking and lubricating the centerstand and sidestand ........6-27 lubricating the rear suspension ...6-28 lubricating the swingarm pivots ...6-28 checking the front fork .................6-28 ...

  • Page 8: Safety Information

    1-1 1 safety information eau1028a be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...

  • Page 9: Safety Information

    Safety information 1-2 1 ● many accidents involve inexperi- enced operators. In fact, many op- erators who have been involved in accidents do not even have a cur- rent motorcycle license. • make sure that you are qualified and that you only lend your mo- torcycle to other qualified opera- tors. • kn...

  • Page 10: Safety Information

    Safety information 1-3 1 avoid carbon monoxide poisoning all engine exhaust contains carbon monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, dizziness, drowsiness, nausea, confu- sion, and eventually death. Carbon monoxide is a colorless, odor- less, tasteless gas which may b...

  • Page 11: Safety Information

    Safety information 1-4 1 tents, can create unstable han- dling or a slow steering re- sponse. ● this vehicle is not designed to pull a trailer or to be attached to a sidecar. Genuine yamaha accessories choosing accessories for your vehicle is an important decision. Genuine yamaha accessories, which ...

  • Page 12: Safety Information

    Safety information 1-5 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...

  • Page 13: Description

    Description 2-1 2 eau10410 left view 1 2 3 4 6 5 7 8 9 10 11 12 1. Coolant reservoir (page 6-16) 2. Accessory box (page 3-39) 3. Owner’s tool kit (page 6-2) 4. Final gear oil filler bolt (page 6-14) 5. Final gear oil drain bolt (page 6-14) 6. Ycc-s clutch fluid reservoir (page 6-23) 7. Air filter el...

  • Page 14: Description

    Description 2-2 2 eau10420 right view 7 8 5,6 4 3 2 1 2 1. Storage compartment (page 3-38) 2. Electronically adjustable suspension system (page 3-42) 3. Fuel tank cap (page 3-32) 4. Windshield (page 3-25/3-13) 5. Fuses (page 6-31) 6. Battery (page 6-30) 7. Brake pedal (page 3-29) 8. Rear brake fluid...

  • Page 15: Description

    Description 2-3 2 eau10430 controls and instruments 1 2 3 4 5 6 1 7 8,9 10 9 1. Rear view mirror (page 3-41) 2. Left handlebar switches (page 3-25) 3. Multi-function meter unit (page 3-11) 4. Main switch/steering lock (page 3-2) 5. Front brake fluid reservoir (page 6-23) 6. Right handlebar switches ...

  • Page 16

    Instrument and control functions 3-1 3 eau10977 immobilizer system this vehicle is equipped with an immo- bilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the fol- lowing: ● a code re-registering key (with a red bow) ● two standard keys (with...

  • Page 17

    Instrument and control functions 3-2 3 ● keep other immobilizer system keys away from the main switch as they may cause signal inter- ference. Eau10472 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various po...

  • Page 18

    Instrument and control functions 3-3 3 to lock the steering 1. Turn the handlebars all the way to the left or right. 2. Push the key in from the “off” po- sition, and then turn it to “lock” while still pushing it. 3. Remove the key. To unlock the steering push the key into the main switch, and then ...

  • Page 19

    Instrument and control functions 3-4 3 eau49393 indicator lights and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indicator light come...

  • Page 20

    Instrument and control functions 3-5 3 if the warning light does not come on initially when the key is turned to “on”, or if the warning light remains on, have a yamaha dealer check the electrical circuit. Eau51661 abs warning light “ ” in normal operation, the abs warning light comes on when the ke...

  • Page 21

    Instrument and control functions 3-6 3 eau55391 electronically adjustable suspen- sion system warning light “ ” this warning light comes on if a prob- lem is detected in the electronically ad- justable suspension system. The electrical circuit of the warning light can be checked by turning the key t...

  • Page 22

    Instrument and control functions 3-7 3 see page 3-26 for an explanation of the stop mode function. Eau54680 immobilizer system indicator light “ ” the electrical circuit of the indicator light can be checked by turning the key to “on”. The indicator light should come on for a few seconds, and then g...

  • Page 23

    Instrument and control functions 3-8 3 activating and setting the cruise control system 1. Push the cruise control power switch “ ” located on the left han- dlebar. The cruise control system indicator light “ ” will come on. 2. Push the “set–” side of the cruise control setting switch to activate th...

  • Page 24

    Instrument and control functions 3-9 3 ● apply the front or rear brake. ● operate the hand shift lever. ● operate the shift pedal. Push the power switch to turn off the cruise control system. The “ ” indica- tor light and the “set” indicator light will go off. Tip traveling speed decreases as soon a...

  • Page 25

    Instrument and control functions 3-10 3 stalls, or the sidestand is lowered, then the “ ” indicator light will go off (the “set” indicator light will not flash). If the cruise control system is automati- cally deactivated, please stop and con- firm that your vehicle is in good operating condition. B...

  • Page 26

    Instrument and control functions 3-11 3 eau55411 multi-function meter unit warning ewa12422 be sure to stop the vehicle before making any setting changes to the multi-function meter unit. Changing settings while riding can distract the operator and increase the risk of an accident. Tip the select sw...

  • Page 27

    Instrument and control functions 3-12 3 tachometer the electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. When the key is turned to “on”, the ta- chometer needle sweeps once across the r/min range and then returns to zero r/min in order to test...

  • Page 28

    Instrument and control functions 3-13 3 ● select the transmission gear that is appropriate for the vehicle speed. Transmission gear display this display shows the selected gear. The neutral position is indicated by the neutral indicator light “ ” and by the transmission gear display “ ”. To avoid da...

  • Page 29

    Instrument and control functions 3-14 3 push the menu switch “menu” to switch the display between the follow- ing functions. The display changes each time the switch is pushed. ● grip warmer adjusting function ● information display selection func- tion ● windshield adjusting function ● damping force...

  • Page 30: 5.0

    Instrument and control functions 3-15 3 ● an average fuel consumption dis- play ● an instantaneous fuel consump- tion display the items shown in each information display can be selected. To set or select the items shown, see page 3-18. Odometer display: tripmeter displays: “trip-1” and “trip-2” show...

  • Page 31: 12.3

    Instrument and control functions 3-16 3 this display is automatically reset when the key is turned to “off”. Tip there are also “time–2” and “time–3” elapsed time displays, but they cannot be set to the information display. See “setting mode” on page 3-18 for de- tailed information. Ambient temperat...

  • Page 32: 12.3

    Instrument and control functions 3-17 3 the average fuel consumption display modes “km/l”, “l/100km” or “mpg” (for the uk only) show the average fuel consumption since the display was last reset. ● the “km/l” display shows the av- erage distance that can be trav- eled on 1.0 l of fuel. ● the “l/100k...

  • Page 33

    Instrument and control functions 3-18 3 setting mode tip ● the transmission must be in neu- tral and the vehicle must be stopped to change settings in this mode. ● shifting the transmission into gear and starting off, or turning the key to “off”, saves all settings made, then exits the setting mode....

  • Page 34

    Instrument and control functions 3-19 3 2. Push the menu switch “menu”. The grip warmer setting display will be shown and “high” will flash in the display. 3. Push the menu switch “menu”. The temperature level for the high setting will start flashing. Use the select switch to set the temperature lev...

  • Page 35: 0:07

    Instrument and control functions 3-20 3 2. Push the menu switch “menu”, and then push the “reset” button to select the item to reset. 3. While the selected item is flashing, push the “reset” button for at least 2 seconds. 4. Push the menu switch “menu” to return to the setting mode menu. Checking an...

  • Page 36

    Instrument and control functions 3-21 3 tip ● for the uk: continue with the fol- lowing steps. ● except for the uk: skip steps 3–5. 3. Push the menu switch “menu”. “km” or “mile” will flash in the dis- play. 4. Use the select switch to select “km” or “mile”, and then push the menu switch “menu”. Tip...

  • Page 37

    Instrument and control functions 3-22 3 3. Use the select switch to highlight the item to change, and then push the menu switch “menu”. 4. Use the select switch to select the item to show, and then push the menu switch “menu”. 5. When you are finished changing the settings, use the select switch to ...

  • Page 38: 5 55

    Instrument and control functions 3-23 3 setting the clock 1. Use the select switch to highlight “clock”. 2. Push the menu switch “menu”. 3. When the hour digits start flashing, use the select switch to set the hours. 4. Push the menu switch “menu”, and the minute digits start flashing. 5. Use the se...

  • Page 39

    Instrument and control functions 3-24 3 this model is equipped with a self-diag- nosis device for various electrical cir- cuits. If a problem is detected in any of those circuits, the engine trouble warn- ing light will come on and the informa- tion display will indicate an error code. If the inform...

  • Page 40

    Instrument and control functions 3-25 3 this mode allows the rider to enjoy smooth drivability from the low-speed range to the high-speed range. Sports mode “s” this mode offers a sportier engine re- sponse in the low- to mid-speed range compared to the touring mode. Eau1234c handlebar switches left...

  • Page 41

    Instrument and control functions 3-26 3 position. To cancel the turn signal lights, push the switch in after it has re- turned to the center position. Eau12500 horn switch “ ” press this switch to sound the horn. Eau55370 start/engine stop switch “ / / ” to crank the engine with the starter, set thi...

  • Page 42

    Instrument and control functions 3-27 3 tip when the stop mode function is activat- ed, the shift down indicator light will flash only when the rider attempts to start off in 2nd gear or higher. Eau54690 drive mode switch “mode” warning ewa15340 do not change the d-mode while the vehicle is moving. ...

  • Page 43

    Instrument and control functions 3-28 3 eau40494 shift pedal this motorcycle is equipped with a con- stant-mesh 5-speed transmission. The shift pedal is located on the left side of the motorcycle. Neutral is at the bottom position. Tip it is impossible to shift gears unless the key is in the “on” po...

  • Page 44

    Instrument and control functions 3-29 3 eau26824 brake lever the brake lever is located on the right side of the handlebar. To apply the front brake, pull the lever toward the throttle grip. The brake lever is equipped with a brake lever position adjusting dial. To adjust the distance between the br...

  • Page 45

    Instrument and control functions 3-30 3 tip ● the abs performs a self-diagno- sis test each time the vehicle first starts off after the key is turned to “on” and the vehicle has traveled at a speed of 10 km/h (6 mi/h) or higher. During this test, a “clicking” noise can be heard from under the seat, ...

  • Page 46

    Instrument and control functions 3-31 3 proach surfaces that may be slippery with caution and avoid es- pecially slippery surfaces. When the key is turned to “on”, the traction control system automatically turns on. The traction control system can be turned on or off manually only when the key is in...

  • Page 47

    Instrument and control functions 3-32 3 to reset the traction control system turn the key to “off”. Wait at least 1 second, then turn the key back to “on”. The “tcs” indicator/warning light should go off and the system will be en- abled. The engine trouble warning light should go off after the motor...

  • Page 48

    Instrument and control functions 3-33 3 eau13221 fuel make sure there is sufficient gasoline in the tank. Warning ewa10881 gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. Before refueli...

  • Page 49

    Instrument and control functions 3-34 3 eaub1301 fuel tank breather/overflow hose before operating the motorcycle: ● check the fuel tank breather/over- flow hose connection. ● check the fuel tank breather/over- flow hose for cracks or damage, and replace it if necessary. ● make sure that the end of ...

  • Page 50

    Instrument and control functions 3-35 3 eau39495 seats passenger seat to remove the passenger seat 1. Insert the key into the seat lock, and then turn it counterclockwise. 2. Lift the front of the passenger seat and pull it forward. To install the passenger seat 1. Insert the projections on the rear...

  • Page 51

    Instrument and control functions 3-36 3 2. Install the passenger seat. Tip ● make sure that the seats are prop- erly secured before riding. ● the rider seat height can be ad- justed to change the riding posi- tion. (see the following section.) eau39632 adjusting the rider seat height the rider seat ...

  • Page 52

    Instrument and control functions 3-37 3 5. Insert the projection on the front of the rider seat into seat holder b as shown. 6. Align the projection on the bottom of the rider seat with the “h” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 7. Install the pass...

  • Page 53

    Instrument and control functions 3-38 3 6. Align the projection on the bottom of the rider seat with the “l” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 7. Install the passenger seat. Tip make sure that the seats are properly secured before riding. Eau14463...

  • Page 54

    Instrument and control functions 3-39 3 eau39480 accessory box the accessory box is located beside the meter panel. To open the accessory box 1. Insert the key into the main switch, and then turn it to “on”. 2. Push the accessory box button, and then open the accessory box lid. 3. Turn the key to “o...

  • Page 55

    Instrument and control functions 3-40 3 eau39641 handlebar position the handlebars can be adjusted to one of three positions to suit the rider’s pref- erence. Have a yamaha dealer adjust the position of the handlebars. Eau54150 opening and closing the cowl- ing vents the cowling vents can be opened ...

  • Page 56

    Instrument and control functions 3-41 3 4. Install the quick fastener. To close a cowling vent 1. Remove the quick fastener. 2. Slide the cowling vent panel for- ward to unhook its projections from the upper slots, and then pull the panel off. 3. Insert the projections into the lower slots, and then...

  • Page 57

    Instrument and control functions 3-42 3 eau55423 adjusting the front and rear suspension this model is equipped with an elec- tronically adjustable suspension sys- tem. The preload of the rear shock absorber and the damping forces of both the front fork and rear shock ab- sorber can be adjusted. War...

  • Page 58

    Instrument and control functions 3-43 3 3. Use the select switch to select the desired preload setting pictogram. Select the suitable setting from the following 4 pictograms according to your load condition. While the preload is being adjust- ed, the information display will show a group of dots mov...

  • Page 59: Hard

    Instrument and control functions 3-44 3 ● if the preload is adjusted repeated- ly, the preload setting pictogram will flash 4 times and the preload cannot be adjusted. Wait approxi- mately 6 minutes for the preload adjusting function motor to cool down, and then try adjusting the preload again. Damp...

  • Page 60: Std

    Instrument and control functions 3-45 3 3. Use the select switch to select “hard”, “std” or “soft”. 4. Push the menu switch “menu”. 5. Use the select switch to select the desired level for the damping force setting. Tip the damping force setting can be set to 7 levels (+3, +2, +1, 0, –1, –2 and –3)....

  • Page 61

    Instrument and control functions 3-46 3 ● do not deform or damage the cylinder in any way. Cylinder damage will result in poor damping performance. ● do not dispose of a damaged or worn-out shock absorber as- sembly yourself. Take the shock absorber assembly to a yamaha dealer for any service. Eau55...

  • Page 62

    Instrument and control functions 3-47 3 eau55361 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch and brake light switches) has the following func- tions. ● it prevents starting when the side- stand is up, but neither brake is ap- plied. ● it pre...

  • Page 63

    Instrument and control functions 3-48 3 with the engine turned off: 1. Place the vehicle on the centerstand. 2. Move the sidestand down. 3. Make sure that the start/engine stop switch is set to “ ”. 4. Turn the key to “on”. 5. Shift the transmission into the neutral position. 6. Keep the front or re...

  • Page 64

    Instrument and control functions 3-49 3 eau39655 auxiliary dc jack warning ewa14360 to prevent electrical shock or short- circuiting, make sure that the cap is installed when the auxiliary dc jack is not being used. Notice eca15431 the accessory connected to the auxiliary dc jack should not be used ...

  • Page 65

    For your safety – pre-operation checks 4-1 4 eau15597 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...

  • Page 66

    For your safety – pre-operation checks 4-2 4 rear brake • check operation. • if soft or spongy, have yamaha dealer bleed hydraulic system. • check brake pads for wear. • replace if necessary. • check fluid level in reservoir. • if necessary, add specified brake fluid to specified level. • check hydr...

  • Page 67

    For your safety – pre-operation checks 4-3 4 sidestand switch • check operation of ignition circuit cut-off system. • if system is not working correctly, have yamaha dealer check vehicle. 3-46 item checks page u1mde0e0.Book page 3 friday, february 15, 2013 1:26 pm.

  • Page 68

    Operation and important riding points 5-1 5 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...

  • Page 69

    Operation and important riding points 5-2 5 ● oil level warning light ● engine trouble warning light ● traction control system indi- cator/warning light ● cruise control indicator lights ● electronically adjustable sus- pension system warning light ● shift down indicator light ● ycc-s system warning...

  • Page 70

    Operation and important riding points 5-3 5 eau55481 shifting shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gears can be shifted using either the shift pedal or the hand shift lever. Refer to page 3-27 for an explanation...

  • Page 71

    Operation and important riding points 5-4 5 eau16810 tips for reducing fuel con- sumption fuel consumption depends largely on your riding style. Consider the following tips to reduce fuel consumption: ● shift up swiftly, and avoid high en- gine speeds during acceleration. ● do not rev the engine whi...

  • Page 72

    Operation and important riding points 5-5 5 eau40582 parking when parking, stop the engine by turn- ing the main switch to “off”, and then remove the key. Tip when the main switch is turned to “off” and the transmission is in gear, the rear wheel cannot be moved. Warning ewa14522 ● always stop the e...

  • Page 73

    Periodic maintenance and adjustment 6-1 6 eau17244 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...

  • Page 74

    Periodic maintenance and adjustment 6-2 6 eau17361 owner’s tool kit the owner’s tool kit is located under the rider seat. (see page 3-35.) the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive mainte...

  • Page 75

    Periodic maintenance and adjustment 6-3 6 eau46861 tip ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (600...

  • Page 76

    Periodic maintenance and adjustment 6-4 6 eau1770f general maintenance and lubrication chart no. Item check or maintenance job odometer reading annual check 1000 km (600 mi) 10000 km (6000 mi) 20000 km (12000 mi) 30000 km (18000 mi) 40000 km (24000 mi) 1 * air filter element • clean. √ √ • replace. ...

  • Page 77

    Periodic maintenance and adjustment 6-5 6 10 * swingarm • check operation and for exces- sive play. √ √ √ √ • lubricate with lithium-soap-based grease. Every 50000 km (30000 mi) 11 * steering bearings • check bearing play and steering for roughness. √ √ √ √ √ • lubricate with lithium-soap-based grea...

  • Page 78

    Periodic maintenance and adjustment 6-6 6 20 * rear suspension re- lay arm and con- necting arm pivoting points • check operation. √ √ √ √ • lubricate with lithium-soap-based grease. √ √ 21 engine oil • change. • check oil level and vehicle for oil leakage. √ √ √ √ √ √ 22 engine oil filter car- trid...

  • Page 79

    Periodic maintenance and adjustment 6-7 6 eau40550 tip ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake and ycc-s clutch service • regularly check and, if necessary, correct the brake and ycc-s clutch fluid levels. • every two years re...

  • Page 80

    Periodic maintenance and adjustment 6-8 6 eau18771 removing and installing pan- els the panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Eau54130 panel a to remove the panel 1...

  • Page 81

    Periodic maintenance and adjustment 6-9 6 3. Take the front cowling off as shown. 4. Remove the bolt, screw and quick fastener, and then take the panel off. To install the panel 1. Place the panel in its original posi- tion, and then install the bolt, screw and quick fastener. 2. Place the front cow...

  • Page 82

    Periodic maintenance and adjustment 6-10 6 3. Pull the bottom of the panel out- ward, pull the front of the panel downward, and then slide the pan- el forward to release it in the rear as shown. To install a panel 1. Place the panel in the original posi- tion, and then install the bolts and the quic...

  • Page 83

    Periodic maintenance and adjustment 6-11 6 eau19652 checking the spark plugs the spark plugs are important engine components, which should be checked periodically, preferably by a yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in ...

  • Page 84

    Periodic maintenance and adjustment 6-12 6 eau19886 engine oil and oil filter car- tridge the engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication cha...

  • Page 85

    Periodic maintenance and adjustment 6-13 6 tip an oil filter wrench is available at a yamaha dealer. 6. Apply a thin coat of clean engine oil to the o-ring of the new oil filter cartridge. Tip make sure that the o-ring is properly seated. 7. Install the new oil filter cartridge, and then tighten it ...

  • Page 86

    Periodic maintenance and adjustment 6-14 6 notice eca11620 ● in order to prevent clutch slip- page (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel speci- fication of “cd” or oils of a high- er quality than specified. In addition, do...

  • Page 87

    Periodic maintenance and adjustment 6-15 6 tip the oil level should be at the brim of the filler hole. 3. If the oil is below the brim of the fill- er hole, add sufficient oil of the rec- ommended type to raise it to the correct level. 4. Check the gasket for damage, and replace it if necessary. 5. ...

  • Page 88

    Periodic maintenance and adjustment 6-16 6 eau20070 coolant the coolant level should be checked before each ride. In addition, the cool- ant must be changed at the intervals specified in the periodic maintenance and lubrication chart. Eau54160 to check the coolant level 1. Place the vehicle on the c...

  • Page 89

    Periodic maintenance and adjustment 6-17 6 eau33031 changing the coolant the coolant must be changed at the in- tervals specified in the periodic mainte- nance and lubrication chart. Have a yamaha dealer change the coolant. Warning! Never attempt to remove the radiator cap when the engine is hot. [e...

  • Page 90

    Periodic maintenance and adjustment 6-18 6 eau21384 checking the throttle grip free play the throttle grip free play should mea- sure 1.0–3.0 mm (0.04–0.12 in) at the inner edge of the throttle grip. Periodi- cally check the throttle grip free play and, if necessary, have a yamaha deal- er adjust it...

  • Page 91

    Periodic maintenance and adjustment 6-19 6 weight of rider, passenger, car- go, and accessories approved for this model. Warning ewa10511 never overload your vehicle. Opera- tion of an overloaded vehicle could cause an accident. Tire inspection the tires must be checked before each ride. If the cent...

  • Page 92

    Periodic maintenance and adjustment 6-20 6 tire information this motorcycle is equipped with tube- less tires, tire air valves and cast wheels. Tires age, even if they have not been used or have only been used occasion- ally. Cracking of the tread and sidewall rubber, sometimes accompanied by carcas...

  • Page 93

    Periodic maintenance and adjustment 6-21 6 speed riding to ride conserva- tively for approximately 100 km (60 mi) after installing a new tire. ● the tires must be warmed up before a high-speed run. ● always adjust the tire air pres- sure according to the operating conditions. Eau21962 cast wheels to...

  • Page 94

    Periodic maintenance and adjustment 6-22 6 eau37913 checking the brake lever free play there should be no free play at the brake lever end. If there is free play, have a yamaha dealer inspect the brake system. Warning ewa14211 a soft or spongy feeling in the brake lever can indicate the presence of ...

  • Page 95

    Periodic maintenance and adjustment 6-23 6 eau22392 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau43431 front brake pads the front brake calipers are equipped with two s...

  • Page 96

    Periodic maintenance and adjustment 6-24 6 rear brake ycc-s clutch tip ● the rear brake fluid reservoir is lo- cated behind panel c. (see page 6-8.) ● the ycc-s clutch fluid reservoir is located behind panel b. (see page 6-8.) warning ewa16020 improper maintenance can result in loss of braking abili...

  • Page 97

    Periodic maintenance and adjustment 6-25 6 check the brake pads for wear and the brake system for leakage. A low ycc-s clutch fluid level may indicate ycc-s clutch system leakage; therefore, be sure to check the ycc-s clutch system for leakage. If the brake or ycc-s clutch fluid level goes down sudd...

  • Page 98

    Periodic maintenance and adjustment 6-26 6 eau23114 checking and lubricating the throttle grip and cable the operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated by a yamaha dealer at the intervals speci- fied in the periodic maintenance ch...

  • Page 99

    Periodic maintenance and adjustment 6-27 6 eau23154 checking and lubricating the brake lever the operation of the brake lever should be checked before each ride, and the lever pivot should be lubricated if nec- essary. Eau23213 checking and lubricating the centerstand and sidestand the operation of ...

  • Page 100

    Periodic maintenance and adjustment 6-28 6 eau23251 lubricating the rear suspen- sion the pivoting points of the rear suspen- sion must be lubricated by a yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. Eaum1652 lubricating the swingarm piv- ots the swinga...

  • Page 101

    Periodic maintenance and adjustment 6-29 6 notice eca10590 if any damage is found or the front fork does not operate smoothly, have a yamaha dealer check or re- pair it. Eau45511 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be ...

  • Page 102

    Periodic maintenance and adjustment 6-30 6 eau39525 battery the battery is located under panel a. (see page 6-8.) this model is equipped with a vrla (valve regulated lead acid) battery. There is no need to check the electro- lyte or to add distilled water. However, the battery lead connections need ...

  • Page 103

    Periodic maintenance and adjustment 6-31 6 is turned to “off”, then con- nect the positive lead before connecting the negative lead. [eca16840] 4. After installation, make sure that the battery leads are properly con- nected to the battery terminals. Notice eca16530 always keep the battery charged. ...

  • Page 104

    Periodic maintenance and adjustment 6-32 6 1. Turn the key to “off” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. Warning! Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive dam...

  • Page 105

    Periodic maintenance and adjustment 6-33 6 eau54240 front turn signal light this model is equipped with led-type front turn signal lights. If a front turn signal light does not come on, have a yamaha dealer check it. Eau27004 replacing a rear turn signal light bulb or a tail/brake light bulb 1. Remo...

  • Page 106

    Periodic maintenance and adjustment 6-34 6 eau24313 replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 2. Remove the license plate light bulb socket (together with the bulb) by pulling it out. 3. Remove the burnt-out bulb by pull- ing it out. 4. Ins...

  • Page 107

    Periodic maintenance and adjustment 6-35 6 eau25871 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and lo...

  • Page 108

    Periodic maintenance and adjustment 6-36 6 eau42504 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the battery. Supply fuel. The engine does not start. Check the battery. Remove the spar...

  • Page 109

    Periodic maintenance and adjustment 6-37 6 engine overheating warning ewat1040 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● place a...

  • Page 110: Motorcycle Care and Storage

    Motorcycle care and storage 7-1 7 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...

  • Page 111: Motorcycle Care and Storage

    Motorcycle care and storage 7-2 7 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or t...

  • Page 112: Motorcycle Care and Storage

    Motorcycle care and storage 7-3 7 windshield. Before using them, make a test by polishing an area which does not affect your visibility. After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Use a chrome polish to shine chrome, aluminum and stainless- steel parts, including t...

  • Page 113: Motorcycle Care and Storage

    Motorcycle care and storage 7-4 7 eau26243 storage short-term always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust sys- tem are cool before covering the motor- cycle. Notice eca10810 ● storing the motorcy...

  • Page 114: Motorcycle Care and Storage

    Motorcycle care and storage 7-5 7 tip make any necessary repairs before storing the motorcycle. U1mde0e0.Book page 5 friday, february 15, 2013 1:26 pm.

  • Page 115: Specifications

    Specifications 8-1 8 dimensions: overall length: 2230 mm (87.8 in) overall width: 750 mm (29.5 in) overall height: 1325/1455 mm (52.2/57.3 in) seat height: 805/825 mm (31.7/32.5 in) wheelbase: 1545 mm (60.8 in) ground clearance: 123 mm (4.84 in) minimum turning radius: 3200 mm (126.0 in) weight: cur...

  • Page 116: Specifications

    Specifications 8-2 8 secondary reduction ratio: 2.698 (35/37 x 21/27 x 33/9) transmission type: constant mesh 5-speed operation: left foot operation gear ratio: 1st: 2.529 (43/17) 2nd: 1.773 (39/22) 3rd: 1.348 (31/23) 4th: 1.077 (28/26) 5th: 0.929 (26/28) chassis: frame type: diamond caster angle: 2...

  • Page 117: Specifications

    Specifications 8-3 8 wheel travel: 125.0 mm (4.92 in) electrical system: ignition system: tci charging system: ac magneto battery: model: gt14b-4 voltage, capacity: 12 v, 12.0 ah headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, 60.0 w/55.0 w × 2 tail/brake light:...

  • Page 118: Consumer Information

    Consumer information 9-1 9 eau48612 identification numbers record the vehicle identification num- ber and model label information in the spaces provided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehicle is stolen. Vehicle identification number: ...

  • Page 119: Index

    Index a abs ...................................................... 3-29 abs warning light ................................... 3-5 accessory box ...................................... 3-39 air filter element.................................... 6-17 auxiliary dc jack .....................................

  • Page 120: Index

    Index stop mode function switch .................... 3-26 storage ................................................... 7-4 storage compartment ........................... 3-38 suspension, adjusting the front and rear ..................................................... 3-42 swingarm pivots, lubricat...

  • Page 121

    U1mde0e0.Book page 3 friday, february 15, 2013 1:26 pm.

  • Page 122

    Printed in japan 2013.03-0.3 ×1 cr (e) dic183 printed on recycled paper original instructions.