1. DL manuals
  2. Yamaha
  3. Motorcycle
  4. FZ6-SAHG
  5. Owner's Manual

Yamaha FZ6-SAHG Owner's Manual

Other manuals for FZ6-SAHG: Owner's Manual, Owner's Manual
Manual is about: 2007

Summary of FZ6-SAHG

  • Page 1

    5s2-28199-ea fz6-sahg owner’s manual.

  • Page 2

    Eau26943 declaration of conformity we company: moric co., ltd. Address: 1450-6 mori mori-machi shuchi-gun shizuoka 437-0292 japan hereby declare that the product: kind of equipment: immobilizer type-designation: 5sl-00 is in compliance with following norm(s) or documents: r&tte directive(1999/5/ec) ...

  • Page 3

    Introduction eau10100 welcome to the yamaha world of motorcycling! As the owner of the fz6-sahg, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take ...

  • Page 4

    Important manual information eau10151 particularly important information is distinguished in this manual by the following notations: note: ● this manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. ● yamaha continuall...

  • Page 5

    Important manual information eau10200 fz6-sahg owner’s manual ©2006 by yamaha motor co., ltd. 1st edition, november 2006 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U5s2e0e0.Book page 2 we...

  • Page 6

    Table of contents safety information ..................1-1 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments.................2-3 instrument and control functions .....

  • Page 7

    Table of contents replacing the license plate light bulb ....................................6-35 replacing an auxiliary light bulb ...6-36 troubleshooting ............................6-37 troubleshooting charts .................6-38 motorcycle care and storage .........................................

  • Page 8

    1-1 1 safety information eau10281 motorcycles are single track vehicles. Their safe use and operation are dependent upon the use of proper riding techniques as well as the ex- pertise of the operator. Ev- ery operator should know the following requirements before riding this motor- cycle. He or she ...

  • Page 9

    Safety information 1-2 1 due to excessive speed or un- dercornering (insufficient lean an- gle for the speed). • always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. • always signal before turning or changing lanes. Make sure that other motorists can s...

  • Page 10

    Safety information 1-3 1 loading the total weight of the operator, pas- senger, accessories and cargo must not exceed the maximum load limit. When loading within this weight limit, keep the following in mind: ● cargo and accessory weight should be kept as low and close to the motorcycle as possible....

  • Page 11

    Safety information 1-4 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...

  • Page 12

    Description 2-1 2 eau10410 left view 1. Main fuse (page 6-31) 2. Battery (page 6-30) 3. Air filter element (page 6-15) 4. Idle adjusting screw (page 6-16) 5. Shock absorber assembly spring preload adjusting ring (page 3-20) 6. Owner’s tool kit (page 6-1) 7. Helmet holder (page 3-19) 8. Shift pedal (...

  • Page 13

    Description 2-2 2 eau10420 right view 1. Fuse box (page 6-31) 2. Storage compartment (page 3-19) 3. Rear brake fluid reservoir (page 6-22) 4. Engine oil filler cap (page 6-9) 5. Front brake fluid reservoir (page 6-22) 6. Radiator cap (page 6-11) 7. Coolant reservoir cap (page 6-11) 8. Coolant drain ...

  • Page 14

    Description 2-3 2 eau10430 controls and instruments 1. Clutch lever (page 3-14) 2. Left handlebar switches (page 3-13) 3. Main switch/steering lock (page 3-2) 4. Multi-function meter unit (page 3-8) 5. Right handlebar switches (page 3-13) 6. Brake lever (page 3-15) 7. Throttle grip (page 6-17) u5s2e...

  • Page 15

    Instrument and control functions 3-1 3 eau10973 immobilizer system this vehicle is equipped with an immo- bilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the fol- lowing. ● a code re-registering key (with a red bow) ● two standard keys (with...

  • Page 16

    Instrument and control functions 3-2 3 ● keep other immobilizer system keys away from the main switch as they may cause signal inter- ference. Eau10471 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. Note: be sure ...

  • Page 17

    Instrument and control functions 3-3 3 to lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “off” po- sition, and then turn it to “lock” while still pushing it. 3. Remove the key. To unlock the steering push the key in, and then turn it to “off” while stil...

  • Page 18

    Instrument and control functions 3-4 3 eau11003 indicator and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indicator light comes on wh...

  • Page 19

    Instrument and control functions 3-5 3 caution: eca10020 do not operate the engine if it is overheated. U5s2e0e0.Book page 5 wednesday, november 29, 2006 1:51 pm.

  • Page 20

    Instrument and control functions 3-6 3 coolant temperature display conditions what to do under 39 °c (under 103 °f) message “lo” is displayed. Ok. Go ahead with riding. 40–116 °c (104–242 °f) temperature is displayed. Ok. Go ahead with riding. 117–139 °c (243–283 °f) temperature display flashes. War...

  • Page 21

    Instrument and control functions 3-7 3 eau42770 engine trouble warning light “ ” this warning light comes on when an electrical circuit monitoring the engine is defective. When this occurs, have a yamaha dealer check the self-diagno- sis system. (see page 3-8 for an expla- nation of the self-diagnos...

  • Page 22

    Instrument and control functions 3-8 3 eau39426 multi-function meter unit warning ewa12421 be sure to stop the vehicle before making any setting changes to the multi-function meter unit. The multi-function meter unit is equipped with the following: ● a speedometer (which shows the riding speed) ● a ...

  • Page 23

    Instrument and control functions 3-9 3 clock the clock displays when the key is turned to “on”. In addition, the clock can be displayed for 10 seconds by pushing the “select” button when the main switch is in the “off”, “lock” or “ ” position. To set the clock 1. Turn the key to “on”. 2. Push the “s...

  • Page 24

    Instrument and control functions 3-10 3 fuel meter the fuel meter indicates the amount of fuel in the fuel tank. The display seg- ments of the fuel meter disappear to- wards “e” (empty) as the fuel level decreases. When the last segment on the left starts flashing, refuel as soon as possible. Note: ...

  • Page 25

    Instrument and control functions 3-11 3 ● when the key is turned to “on”, the coolant temperature is auto- matically displayed, even if the air intake temperature was displayed prior to turning the key to “off”. ● when the air intake temperature display is selected, “a” is displayed for one second, ...

  • Page 26

    Instrument and control functions 3-12 3 lcd and tachometer brightness control mode this function allows you to adjust the brightness of the lcd and the tachom- eter panel and needle to suit the out- side lighting conditions. To set the brightness 1. Turn the key to “off”. 2. Push and hold the “selec...

  • Page 27

    Instrument and control functions 3-13 3 eau12347 handlebar switches left right eau12350 pass switch “ ” press this switch to flash the headlight. Eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-han...

  • Page 28

    Instrument and control functions 3-14 3 eau42340 the engine trouble warning light and abs warning light will come on when the key is turned to “on” and the start switch is pushed, but this does not indi- cate a malfunction. Eau12733 hazard switch “ ” with the key in the “on” or “ ” posi- tion, use t...

  • Page 29

    Instrument and control functions 3-15 3 eau26822 brake lever the brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handle- bar grip. The brake lever is equipped with a po- sition adjusting dial. To adjust the dis- tance between the brake lever an...

  • Page 30

    Instrument and control functions 3-16 3 ● this abs has a test mode which allows the owner to experience the pulsating at the brake lever or brake pedal when the abs is oper- ating. However, special tools are required, so please consult your yamaha dealer when performing this test. Eau13072 fuel tank...

  • Page 31

    Instrument and control functions 3-17 3 eau13220 fuel make sure that there is sufficient fuel in the tank. When refueling, be sure to in- sert the pump nozzle into the fuel tank filler hole and to fill the tank to the bot- tom of the filler tube as shown. Warning ewa10880 ● do not overfill the fuel ...

  • Page 32

    Instrument and control functions 3-18 3 eau13412 fuel tank breather hose before operating the motorcycle: ● check the fuel tank breather hose connection. ● check the fuel tank breather hose for cracks or damage, and replace it if damaged. ● make sure that the fuel tank breather hose is not blocked, ...

  • Page 33

    Instrument and control functions 3-19 3 2. Push the rear of the seat down to lock it in place. 3. Remove the key. Note: make sure that the seat is properly se- cured before riding. Eau14281 helmet holder to open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock...

  • Page 34

    Instrument and control functions 3-20 3 ● do not exceed the maximum load of 185 kg (408 lb) for the ve- hicle. Eau36462 adjusting the shock absorber assembly this shock absorber assembly is equipped with a spring preload adjust- ing ring. Caution: eca10100 never attempt to turn an adjusting mechanis...

  • Page 35

    Instrument and control functions 3-21 3 3. Install the seat. Warning ewa10220 this shock absorber contains highly pressurized nitrogen gas. For prop- er handling, read and understand the following information before handling the shock absorber. The manufacturer cannot be held re- sponsible for prope...

  • Page 36

    Instrument and control functions 3-22 3 eau15321 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. ● it prevents starting when the trans- mission is in gear and the side- stand is u...

  • Page 37

    Instrument and control functions 3-23 3 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? With the engine still runni...

  • Page 38

    Pre-operation checks 4-1 4 eau15592 the condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air p...

  • Page 39

    Pre-operation checks 4-2 4 eau15605 pre-operation check list item checks page fuel • check fuel level in fuel tank. • refuel if necessary. • check fuel line for leakage. 3-17 engine oil • check oil level in engine. • if necessary, add recommended oil to specified level. • check vehicle for oil leaka...

  • Page 40

    Pre-operation checks 4-3 4 throttle grip • make sure that operation is smooth. • check cable free play. • if necessary, have yamaha dealer adjust cable free play and lubricate cable and grip housing. 6-17, 6-26 control cables • make sure that operation is smooth. • lubricate if necessary. 6-26 drive...

  • Page 41

    Operation and important riding points 5-1 5 eau15950 warning ewa10270 ● become thoroughly familiar with all operating controls and their functions before riding. Consult a yamaha dealer re- garding any control or function that you do not thoroughly un- derstand. ● never start the engine or oper- ate...

  • Page 42

    Operation and important riding points 5-2 5 serve the battery. Do not crank the en- gine more than 10 seconds on any one attempt. Caution: eca15700 ● if the oil level warning light flick- ers or remains on after starting, immediately stop the engine, and then check the engine oil level and the vehic...

  • Page 43

    Operation and important riding points 5-3 5 caution: eca10260 ● even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running. ...

  • Page 44

    Operation and important riding points 5-4 5 caution: eca10301 after 1000 km (600 mi) of operation, the engine oil must be changed and the oil filter cartridge or element re- placed. 1600 km (1000 mi) and beyond the vehicle can now be operated nor- mally. Caution: eca10310 ● keep the engine speed out...

  • Page 45

    Periodic maintenance and minor repair 6-1 6 eau17240 safety is an obligation of the owner. Pe- riodic inspection, adjustment and lubri- cation will keep your vehicle in the safest and most efficient condition pos- sible. The most important points of in- spection, adjustment, and lubrication are expl...

  • Page 46

    Periodic maintenance and minor repair 6-2 6 eau17707 periodic maintenance and lubrication chart note: ● the annual checks must be performed every year, except if a kilometer-based maintenance is performed in- stead. ● from 50000 km, repeat the maintenance intervals starting from 10000 km. ● items ma...

  • Page 47

    Periodic maintenance and minor repair 6-3 6 10 * tires • check tread depth and for damage. • replace if necessary. • check air pressure. • correct if necessary. √ √ √ √ √ 11 * wheel bearings • check bearing for looseness or damage. √ √ √ √ 12 * swingarm • check operation and for excessive play. √ √ ...

  • Page 48

    Periodic maintenance and minor repair 6-4 6 eau18680 note: ● air filter • this model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it. 23 engine oil • change. • check oil level and vehicle for oil leakage. √ √ √...

  • Page 49

    Periodic maintenance and minor repair 6-5 6 • the air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas. ● hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal components of th...

  • Page 50

    Periodic maintenance and minor repair 6-6 6 eau18771 removing and installing pan- els the panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Eau42661 panels a and b to remove on...

  • Page 51

    Periodic maintenance and minor repair 6-7 6 eau42690 panel c to remove the panel 1. Remove panels a and b. (see page 6-6.) 2. Remove the bolts, and then take the panel off. To install the panel 1. Place the panel in the original posi- tion, and then install the bolts. 2. Install panels a and b. Eau3...

  • Page 52

    Periodic maintenance and minor repair 6-8 6 eau19642 checking the spark plugs the spark plugs are important engine components, which should be checked periodically, preferably by a yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in...

  • Page 53

    Periodic maintenance and minor repair 6-9 6 eau42620 engine oil and oil filter car- tridge the engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication ch...

  • Page 54

    Periodic maintenance and minor repair 6-10 6 note: skip steps 4–6 if the oil filter cartridge is not being replaced. 4. Remove the oil filter cartridge with an oil filter wrench. Note: an oil filter wrench is available at a yamaha dealer. 5. Apply a thin coat of engine oil to the o-ring of the new o...

  • Page 55

    Periodic maintenance and minor repair 6-11 6 caution: eca11620 ● in order to prevent clutch slip- page (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel speci- fication of “cd” or oils of a high- er quality than specified. In addition...

  • Page 56

    Periodic maintenance and minor repair 6-12 6 note: the coolant should be between the minimum and maximum level marks. 3. If the coolant is at or below the minimum level mark, remove the reservoir cap. 4. Add coolant or distilled water to raise the coolant to the maximum level mark, install the coola...

  • Page 57

    Periodic maintenance and minor repair 6-13 6 2. Place a container under the engine to collect the used coolant. 3. Remove the radiator cap retaining bolt, radiator cap retainer and radi- ator cap. Warning ewa10380 never attempt to remove the radiator cap when the engine is hot. 4. Remove the coolant...

  • Page 58

    Periodic maintenance and minor repair 6-14 6 11. Pour the specified amount of the recommended coolant into the ra- diator and reservoir. Caution: eca10471 ● if coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engi...

  • Page 59

    Periodic maintenance and minor repair 6-15 6 eau32886 replacing the air filter element the air filter element should be re- placed at the intervals specified in the periodic maintenance and lubrication chart. Replace the air filter element more frequently if you are riding in un- usually wet or dust...

  • Page 60

    Periodic maintenance and minor repair 6-16 6 warning ewa12462 ● before placing the fuel tank in the original position, make sure that all hoses (i.E., fuel hose, fuel tank breather hose, fuel tank overflow hose) are not damaged, that they are properly connected and routed, and that they are not pinc...

  • Page 61

    Periodic maintenance and minor repair 6-17 6 note: if the specified idling speed cannot be obtained as described above, have a yamaha dealer make the adjustment. Eau21382 checking the throttle cable free play the throttle cable free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the throttle gri...

  • Page 62

    Periodic maintenance and minor repair 6-18 6 eau21771 tires to maximize the performance, durabil- ity, and safe operation of your motor- cycle, note the following points regarding the specified tires. Tire air pressure the tire air pressure should be checked and, if necessary, adjusted before each r...

  • Page 63

    Periodic maintenance and minor repair 6-19 6 tire inspection the tires must be checked before each ride. If the center tread depth reaches the specified limit, if the tire has a nail or glass fragments in it, or if the sidewall is cracked, have a yamaha dealer re- place the tire immediately. Note: t...

  • Page 64

    Periodic maintenance and minor repair 6-20 6 warning ewa10600 this motorcycle is fitted with super- high-speed tires. Note the following points in order to make the most ef- ficient use of these tires. ● use only the specified replace- ment tires. Other tires may run the danger of bursting at super ...

  • Page 65

    Periodic maintenance and minor repair 6-21 6 eau22080 adjusting the clutch lever free play the clutch lever free play should mea- sure 10.0–15.0 mm (0.39–0.59 in) as shown. Periodically check the clutch le- ver free play and, if necessary, adjust it as follows. To increase the clutch lever free play...

  • Page 66

    Periodic maintenance and minor repair 6-22 6 eau22390 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau36890 front brake pads each front brake pad is provided with wear ind...

  • Page 67

    Periodic maintenance and minor repair 6-23 6 before riding, check that the brake fluid is above the minimum level mark and replenish if necessary. A low brake fluid level may indicate worn brake pads and/or brake system leakage. If the brake fluid level is low, be sure to check the brake pads for we...

  • Page 68

    Periodic maintenance and minor repair 6-24 6 eau22760 drive chain slack the drive chain slack should be checked before each ride and adjusted if necessary. Eau22793 to check the drive chain slack 1. Place the motorcycle on the cen- terstand. 2. Shift the transmission into the neu- tral position. 3. ...

  • Page 69

    Periodic maintenance and minor repair 6-25 6 eau23022 cleaning and lubricating the drive chain the drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet are...

  • Page 70

    Periodic maintenance and minor repair 6-26 6 eau23100 checking and lubricating the cables the operation of all control cables and the condition of the cables should be checked before each ride, and the ca- bles and cable ends should be lubricat- ed if necessary. If a cable is damaged or does not mov...

  • Page 71

    Periodic maintenance and minor repair 6-27 6 eau23140 checking and lubricating the brake and clutch levers brake lever clutch lever the operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lu- bricated if necessary. Recommended lubricant: lithiu...

  • Page 72

    Periodic maintenance and minor repair 6-28 6 eau23211 checking and lubricating the centerstand and sidestand the operation of the centerstand and sidestand should be checked before each ride, and the pivots and metal-to- metal contact surfaces should be lubri- cated if necessary. Warning ewa10740 if...

  • Page 73

    Periodic maintenance and minor repair 6-29 6 caution: eca10590 if any damage is found or the front fork does not operate smoothly, have a yamaha dealer check or re- pair it. Eau23280 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must...

  • Page 74

    Periodic maintenance and minor repair 6-30 6 eau23290 checking the wheel bearings the front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrica- tion chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a yamaha ...

  • Page 75

    Periodic maintenance and minor repair 6-31 6 ● keep this and all batter- ies out of the reach of children. To store the battery 1. If the vehicle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. 2. If the battery will be stored fo...

  • Page 76

    Periodic maintenance and minor repair 6-32 6 fuse box 2 is located behind panel d. (see page 6-6.) if a fuse is blown, replace it as follows. 1. Turn the key to “off” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. Cau...

  • Page 77

    Periodic maintenance and minor repair 6-33 6 3. Turn the key to “on” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a yamaha dealer check the electrical system. Eau23740 replacing the headlight bulb this model is equipped ...

  • Page 78

    Periodic maintenance and minor repair 6-34 6 ● headlight bulb do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transpar- ency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thor- oughly clean off any dirt and fin- gerp...

  • Page 79

    Periodic maintenance and minor repair 6-35 6 4. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 5. Install the socket (together with the bulb) by turning it clockwise. 6. Install the seat. Eau24202 replacing a turn signal light bulb 1. Remove the turn sign...

  • Page 80

    Periodic maintenance and minor repair 6-36 6 3. Remove the defective bulb by pull- ing it out. 4. Insert a new bulb into the socket. 5. Install the socket (together with the bulb) by pushing it in. 6. Install the license plate light unit by installing the screws. Eau42650 replacing an auxiliary ligh...

  • Page 81

    Periodic maintenance and minor repair 6-37 6 eau25870 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and ...

  • Page 82

    Periodic maintenance and minor repair 6-38 6 eau42360 troubleshooting charts starting problems or poor engine performance warning ewa10840 keep away open flames and do not smoke while checking or working on the fuel system. Check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There i...

  • Page 83

    Periodic maintenance and minor repair 6-39 6 engine overheating warning ewa10400 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● after...

  • Page 84

    Motorcycle care and storage 7-1 7 eau37833 matte color caution caution: eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compoun...

  • Page 85

    Motorcycle care and storage 7-2 7 cleaning products, solvent or thinner, fuel (gasoline), rust re- movers or inhibitors, brake flu- id, antifreeze or electrolyte. ● do not use high-pressure wash- ers or steam-jet cleaners since they cause water seepage and deterioration in the following ar- eas: sea...

  • Page 86

    Motorcycle care and storage 7-3 7 4. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stone...

  • Page 87

    Motorcycle care and storage 7-4 7 3. Perform the following steps to pro- tect the cylinders, piston rings, etc. From corrosion. A. Remove the spark plug caps and spark plugs. B. Pour a teaspoonful of engine oil into each spark plug bore. C. Install the spark plug caps onto the spark plugs, and then ...

  • Page 88

    Specifications 8-1 8 dimensions: overall length: 2095 mm (82.5 in) overall width: 750 mm (29.5 in) overall height: 1210 mm (47.6 in) seat height: 795 mm (31.3 in) wheelbase: 1440 mm (56.7 in) ground clearance: 145 mm (5.71 in) minimum turning radius: 2800 mm (110.2 in) weight: with oil and fuel: 212...

  • Page 89

    Specifications 8-2 8 gear ratio: 1st: 37/13 (2.846) 2nd: 37/19 (1.947) 3rd: 28/18 (1.556) 4th: 32/24 (1.333) 5th: 25/21 (1.190) 6th: 26/24 (1.083) chassis: frame type: diamond caster angle: 25.00 ° trail: 97.5 mm (3.84 in) front tire: type: tubeless size: 120/70 zr17m/c (58w) manufacturer/model: bri...

  • Page 90

    Specifications 8-3 8 electrical system: ignition system: transistorized coil ignition (digital) charging system: ac magneto battery: model: gt12b-4 voltage, capacity: 12 v, 10.0 ah headlight: bulb type: halogen bulb bulb voltage, wattage × quantity: headlight: 12 v, 60 w/55.0 w × 1 headlight: 12 v, ...

  • Page 91

    Consumer information 9-1 9 eau26351 identification numbers record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehi- cle is stolen. ...

  • Page 92

    Consumer information 9-2 9 eau26480 model label the model label is affixed to the frame under the seat. (see page 3-18.) record the information on this label in the space provided. This information will be needed when ordering spare parts from a yamaha dealer. 1. Model label u5s2e0e0.Book page 2 wed...

  • Page 93

    Index a abs ...................................................... 3-15 abs warning light ................................... 3-7 air filter element, replacing ................... 6-15 anti-theft alarm (optional) ..................... 3-12 auxiliary light bulb, replacing ................ 6-36 b batt...

  • Page 94

    Index troubleshooting .................................... 6-37 troubleshooting charts ......................... 6-38 turn signal indicator lights ...................... 3-4 turn signal light bulb, replacing ............ 6-35 turn signal switch ................................. 3-13 v valve clearanc...

  • Page 95

    U5s2e0e0.Book page 3 wednesday, november 29, 2006 1:51 pm.

  • Page 96

    Printed on recycled paper yamaha motor co., ltd. Printed in japan 2006.12-0.3 × 1 cr (e).