Yamaha P50-m Owner's Manual - page 44
35
SOUND LISTS & MIDI DATA
1.5 Program Change
1100nnnn
Cn
Status
n= channel number
0ppppppp
pp
Program No. p=0~127
Program Change messages are not received when the Part
Parameter setting Rcv PROGRAM CHANGE = OFF.
When MIDI PROGRAM CHANGE TABLE = OFF, values
other than 0~28 are ignored.
1.6 Channel Aftertouch
1101nnnn
Dn
Status
n= channel number
0vvvvvvv
vv
Value
v=0~127
With the default settings, this has no function.
Channel Aftertouch messages are not received when the
Part Parameter setting Rcv CHANNEL AFTER TOUCH =
OFF.
1.7 Pitch Bend Change
1110nnnn
En
Status
n= channel number
0lllllll
ll
Value LSB
0mmmmmmm
mm
Value MSB
Pitch Bend Change messages are not received when the Part
Parameter setting Rcv PITCH BEND CHANGE = OFF.
2. Channel Mode Messages
2.1 All Sound Off
1011nnnn
Bn
Status
n= channel number
01111000
78
Control No.
00000000
00
Control Value
All sounding notes on the corresponding channel will be
silenced.
However the status of channel messages such as Note On
and Hold On will be maintained.
2.2 Reset All Controllers
1011nnnn
Bn
Status
n= channel number
01111001
79
Control No.
00000000
00
Control Value
The values of the following controllers will change.
Controller
Setting value
Pitch Bend Range
+/–0 (center)
Channel Aftertouch
0 (off)
Polyphonic Aftertouch
0 (off)
Modulation
0 (off)
Expression
127(maximum)
Hold
0 (off)
Portamento
0 (off)
Sostenuto
0 (off)
Soft Pedal
0 (off)
Portamento Control
Reset the Portamento Source
Note number that was received
RPN
Number un-specified, internal
data not changed.
NRPN
Number un-specified, internal
data not changed.
2.3 All Note Off
1011nnnn
Bn
Status
n= channel number
01111011
7B
Control No.
00000000
00
Control Value
All notes of the corresponding channel that are currently on
will be turned off.
However if Hold1 or Sostenuto are on, the sound will con-
tinue until these are off.
2.4 Omni Off
1011nnnn
Bn
Status
n= channel number
01111100
7C
Control No.
00000000
00
Control Value
This performs the same processing as when All Note Off is
received.
2.5 Omni On
1011nnnn
Bn
Status
n= channel number
01111101
7D
Control No.
00000000
00
Control Value
This performs the same processing as when All Note Off is
received.
2.6 Mono
1011nnnn
Bn
Status
n= channel number
01111110
7E
Control No.
00000000
00
Control Value
This performs the same processing as when All Sound Off
is received, and if the 3rd byte (the mono number) is in the
range 0~16, sets the instrument to Mode 4 (m=1).
2.7 Poly
1011nnnn
Bn
Status
n= channel number
01111111
7E
Control No.
00000000
00
Control Value
This performs the same processing as when All Sound Off
is received, and sets the instrument to Mode 3.
3. System Exclusive Messages
3.1 Parameter Changes
This instrument receives the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI Mode On
[ XG NATIVE ]
1) XG System on
2) XG System Data parameter change
3) Multi Effect1 Data parameter change
4) Part Data parameter change
[ P50-m NATIVE ]
1) P50-m System data parameter change
2) Remote switch
[ Other ]
1) Master tuning
3.1.1
Universal Realtime Messages
3.1.1.1 Master Volume
11110000 F0 Exclusive status
01111111 7F Universal Real Time
01111111 7F ID of target device
00000100 04 Sub-ID #1=Device Control Message
00000001 01 Sub-ID #2=Master Volume
0sssssss ss Volume LSB
0ttttttt tt Volume MSB
11110111 F7 End of Exclusive
Alternatively,
11110000 F0 Exclusive status
01111111 7F Universal Real Time
0xxxnnnn xn Device No.xxx = don’t care