Yamaha YSP-1 Service Manual

Summary of YSP-1

  • Page 1

    Service manual digital sound projector ysp-1 ■ contents to service personnel .......................................... 2 front panel .............................................................. 3 rear panels .............................................................. 3 remote control panels .....

  • Page 2

    Ysp-1 2 ysp-1 warning: chemical content notice! The solder used in the production of this product contains lead. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the california health and welfare agency (and possibly ...

  • Page 3

    Ysp-1 3 ysp-1 ■ front panel bottom view ■ rear panels u, c models t model k model b, g models l model j model r model a model j model only.

  • Page 4

    Ysp-1 4 ysp-1 ■ remote control panels ■ specifications / 参考仕様 ■ audio section / オーディオ部 minimum rms output power (power amp. Section) / 定格出力 (パ ワーアンプ部) woofer [100hz, 10%thd, 4 ohms] ................................. 20w x 2 tweeter [1khz, 10%thd, 10 ohms] ................................ 2w x 40 inp...

  • Page 5

    Ysp-1 5 ■ internal view 3 4 6 7 1 driver, woofer 2 driver, tweeter 3 input (3) p.C.B. 4 input (4) p.C.B. 5 amp p.C.B. 6 input (2) p.C.B. 7 dsp p.C.B. 8 switching power supply unit 9 input (5) p.C.B. 4 input (1) p.C.B. Front view rear view rear unit 2 2 1 1 5 8 9 0 5 • dimensions / 寸法図 118 (4-11/16")...

  • Page 6

    Ysp-1 6 ■ set menu table / セット メニ ュー *1... Distance between this unit and floor. / 本機と床との距離 *2... Distance in the lateral direction of the room (length of the wall on the left side of the user) / 部屋の横方向の距離 (ユーザーの左側壁の距離 ) *3... Distance in the longitudinal direction of the room (length of the wall on...

  • Page 7

    Ysp-1 7 ysp-1 1 1 1 1 2 top panel トップパネル top panel トップパネル plate/ top プレート/トップ fig. 1 1. Removal of top panels and plate/top a. Remove 8 screws (1). (fig. 1) b. Remove 2 top panels. C. Remove 2 screws (2). (fig. 1) d. Remove the plate/top. 1. トップパネル、プレート/トップの外し方 a. ①のネジ 8本を外します。(fig. 1) b. トップパネル 2個を...

  • Page 8

    Ysp-1 8 ysp-1 when checking the p.C.B. : • the rear unit removed from the unit does not work because its grounding is loose. Be sure to connect the ground of the rear unit to the chassis or gnd with a lead wire or the like. (fig. A) • reconnect all cables (connectors) that have been disconnected. Be...

  • Page 9

    Ysp-1 9 ysp-1 3. Input (2) p.C.B.の外し方 a. ④のネジ 14本を外します。(fig. 4) b. パッドl 3個を外します。(fig. 4) c. プレート/シールドを取り外します。 d. ⑤のネジ 4本を外します。(fig. 5) e. コネクター cb7、cb9、cb302を外します。(fig. 5) f. Input(2)p.C.B.を取り外します。 3. Removal of input (2) p.C.B. A. Remove 14 screws (4). (fig. 4) b. Remove 3 pad l’s. (fig. 4) c. Remo...

  • Page 10

    Ysp-1 10 ysp-1 5. フロントパネルユニットの外し方 a. ⑧のネジ 17本を外します。(fig. 7) b. フロントパネルユニットを取り外します。 c. ⑨のネジ 2本を外します。(fig. 8) d. ストッパーフレームを取り外します。 5. Removal of front panel unit a. Remove 17 screws (8). (fig. 7) b. Remove the front panel unit. C. Remove 2 screws (9). (fig. 8) d. Remove the stopper frame. 8 8 8 8 8 fr...

  • Page 11

    Ysp-1 11 ysp-1 installation of driver (tweeter) caution : make sure that all the removed driver (tweeter) parts are reinstalled at specified positions. (fig. B) スピーカーユニット (ツイーター) の取り付け方 注意:取り外したスピーカーユニット (ツイーター)はすべ て決められた位置に取り付けてください。(fig. B) a1 b1 a2 b2 c1 a3 b3 c2 a4 b4 c3 a5 b5 c4 a6 b6 c5 a7 b7 ...

  • Page 12

    Ysp-1 12 ysp-1 d d e e b b c c c c side cover l サイドカバーl side cover r サイドカバーr plate side プレート/サイド plate side プレート/サイド plate cover プレート/カバー plate cover プレート/カバー front grille フロントグリル driver, woofer スピーカーユニット、ウーファー driver, woofer スピーカーユニット、ウーファー 7. Removal of driver (woofer) a. Remove 4 screws (b). (fig...

  • Page 13

    Ysp-1 13 ysp-1 ・rs232cクロスケーブル“d-sub 9pin メス” (仕様) pin no.2 rxd pin no.2 rxd pin no.3 txd pin no.3 txd pin no.5 gnd pin no.5 gnd pin no.7 rts pin no.7 rts pin no.8 cts pin no.8 cts ● 操作前の準備と注意 ・ p c へ指定のダウンロード先からf l a s h s t a . E x e と spdownloader_2_0_7_xxx.Exeをダウンロードしてく ださい。 ・ rs232cクロスケーブルは必ず上記仕...

  • Page 14

    Ysp-1 14 ysp-1 ● 操作方法 cpuの場合 1. Pcにflashsta.Exeをインストールします。 2. Ysp-1とpcの電源を入れる前に、それぞれのrs232c ポート間をrs232cケーブル(クロスケーブル)で接続し ます。(fig. 1) ● operation procedure for cpu 1. Install flashsta.Exe into the pc. 2. Before turning on the power to ysp-1 and pc, connect between rs232c ports with the rs232c cable (...

  • Page 15

    Ysp-1 15 ysp-1 6.[refer...]ボタンを押し、書き込むファームウェアを選 択します。 ※ id項目は書込みファイル選択時、自動的に取り込ま れます。 6. Press the [refer...] button. And select the firmware name. * the id code is loaded when the file is selected. 7. Press the [setting] button and set the transmission rate. 7.[setting]ボタンを押し、通信速度の設定を行います。 8. Press...

  • Page 16

    Ysp-1 16 ysp-1 for dsp 1. Install spdownloader_2_0_7_xxx.Exe into the pc. 2. Before turning on the power to ysp-1 and pc, connect between rs232c ports with the rs232c cable (cross cable). (fig. 1) 3. Connect the power cable of ysp-1 to the ac outlet. While pressing the “vol+” key and “vol-” key of t...

  • Page 17

    Ysp-1 17 ysp-1 select the port of rs-232c 接続しているrs-232cポートを選択します select spcm protocol spcmプロトコルを選択します 5. Select the data to be transmitted and port. · com port select the port of rs-232c. · d/load protocol select “spcm protocol” 5. 送信データ、ポートを選択します。 ・ com port 接続しているrs-232Cポートを選択します。 ・ d/load protoco...

  • Page 18

    Ysp-1 18 ysp-1 confirm “ok” “ok”であることを確認します 3 after downloading sccessfully, “download ‘*****’ ok” is appeared. Confirm “dload ok” on the serial log window. 3 書き込み完了後、“download ‘*****’ ok” が表示さ れます。 serial logウィンドウの“dload ok”を確認しま す。 firm software target dsp application spcm application spid spcm in...

  • Page 19

    Ysp-1 19 ysp-1 1 using the “up” or “down” key of the remote controller, select the diag menu in the figure below. ① リモコンの“up” キーまたは “down” キーを使い、下 図のダイアグメニューを選択します。 ④ ファームウェアのバージョンを確認します。 ダイアグメニューdsp ver./midを表示し、以下の ように同様のバージョンになれば完了です。 4 check the version of the firmware. The procedure has been co...

  • Page 20

    Ysp-1 20 ysp-1 ■ self diagnosis function (diag) / 自己診断機能(ダイアグ) there are 14 diag menu items, each of which has sub- menu items. Listed in the table below are menu items and sub-menu items. ダイアグメニューは1 4 個あり、そのそれぞれにサブメ ニューがあります。下表はメニュー一覧です。 no. Diag menu sub menu dsp through (yss948-yss930) pro logic ...

  • Page 21

    Ysp-1 21 ysp-1 • starting diag to activate the diag function, press the “standby/on” key of the remote controller while pressing the keys of the main unit as shown below at the same time. ● ダイアグの起動 本体の下図に示すキーを同時に押しながらリモコンの “standby/on”キーを押すと、ダイアグが起動します。 • starting diag in the protection cancel mode ...

  • Page 22

    Ysp-1 22 ysp-1 cause: the voltage in the power supply section is abnormal. Supplementary information: the abnormal voltage is displayed in % based on 3.3v as 100%. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply w...

  • Page 23

    Ysp-1 23 ysp-1 • display during menu operation during the diag operation, the menu list described in the s e c t i o n o f t h e s t a r t u p s c r e e n a p p e a r s o n t h e superimposed screen and the function at work is indicated on the fl indicator. The contents displayed during the function...

  • Page 24

    Ysp-1 24 ysp-1 • functions in diag mode in addition to the diag menu items, functions as listed below are available. • input selection • muting • night • power on/off • master volume * functions related to the set menu are not available. • initial settings used to start diag the following initial se...

  • Page 25

    Ysp-1 25 ysp-1 dsp thr front l • front l output without the head margin is provided in digital full bit. • the swfr signal is output but not in digital full bit. Dsp thr front l ・ ヘ ッ ド マ ー ジ ン を 含 ま ず 、 デ ジ タ ル フ ル ビ ッ ト で front lが出力されます。 ・ swfrは出力されますが、デジタルフルビットではあり ません。 • details of diag menu wit...

  • Page 26

    Ysp-1 26 ysp-1 dsp thr surround r • surround r output without the head margin is provided in digital full bit. • the swfr signal is output but not in digital full bit. Dsp thr surround r ・ ヘ ッ ド マ ー ジ ン を 含 ま ず 、 デ ジ タ ル フ ル ビ ッ ト で surround rが出力されます。 ・ swfrは出力されますが、デジタルフルビットではあり ません。 dsp thr surrou...

  • Page 27

    Ysp-1 27 ysp-1 2. Pro logic / neo6 pro logic i, ii, neo:6 can be selected from the sub menu items. Pro logic ii 2. Pro logic / neo6 サブメニューでpro logic i、ii、neo:6を選択可能です。 pro logic ii sbl/ sbr c/lfe sl/sr yss948 tms320c6713bgdp yss930 lc89057 tac8256 analog a/d dir decode dsp post processing dsp ak5381...

  • Page 28

    Ysp-1 28 ysp-1 initial display 初期表示 all segments off 全セグメント消灯 all segments on (dimmer 100%) 全セグメント点灯(ディマー100%) all segments on (dimmer 50%) 全セグメント点灯(ディマー50%) lighting of segments in lattice セグメント格子状点灯 lighting in lattice 格子状点灯 normal 正常 short ショート segment conditions of the fl driver and the fl tube ...

  • Page 29

    Ysp-1 29 ysp-1 hard flow this sub-menu is used to check operation of the flow port of the hardware. “ok” appears when the check result is satisfactory and “ng” when it is not. Hard flow ハードウェアフローポートの動作チェックを行います。正 常にチェック完了した場合、“ok”と表示します。正常に チェック完了しなかった場合は“ng”と表示します。 5. Rs-232c this menu is used to c...

  • Page 30

    Ysp-1 30 ysp-1 6. Factory preset this menu is used to reserve and inhibit initialization of the back-up ram. The signals are processed using effect off. (the l/r signal is output using analog main bypass.) preset inhibit (initialization inhibited) / preset inhibit(初期化禁止) ram initialization is not ex...

  • Page 31

    Ysp-1 31 ysp-1 7. Ad data check this menu is used to display the a/d conversion value of the main cpu which detects panel keys of the main unit and protection functions in % using the sub-menu. During signal processing, the condition before execution is maintained. * the figures in the diagram are g...

  • Page 32

    Ysp-1 32 ysp-1 ti1-2 not applied to this model. Cs1-5 indicates channel status information of the input signal (iec60958). Bs1-7 indicates information of the bit stream included in the dts signal. Mtt mute trigger cs 1-5 入力信号のiec60958チャンネルステータス情報を表示し ます。 bs1-7 dts、dolby digital、aac信号に含まれるビットストリーム イン...

  • Page 33

    Ysp-1 33 ysp-1 11. Microprocessor information there are 4 sub menu items. The version, checksum and the port specified by the microprocessor are displayed. The signal is processed using effect off. The checksum is obtained by adding the data at every 16 bits for each program area and expressing the ...

  • Page 34

    Ysp-1 34 ysp-1 12. Date there are 4 sub menu items. The updated date of the program, clearance of the protection history and the remote control reception code are displayed. When remo code menu is selected, keys become non- operable due to detection of the values of all keys. However, it is possible...

  • Page 35

    Ysp-1 35 ysp-1 13. 1 sp test one sp test have the sound produced from each driver to check its condition and installation position. Use the “select” and “return” keys of the remote controller for selection. 13. 1 sp test one sp test 各スピーカーユニットを鳴らし、不良・取付位置の確認を します。 リモコンの “select” キー、 “return” キーを使って選...

  • Page 36

    Ysp-1 36 ysp-1 14. Dsp ver dsp the version of application code is displayed. 14. Dsp ver dsp application codeのバージョンを表示します。 csc the version of core start-up code is displayed. Csc core start-up codeのバージョンを表示します。 mid the version of spid is displayed. * spid is the abbreviation for the sound projector ...

  • Page 37

    Ysp-1 37 ysp-1 ■ display data ● v1 : 15-bt-99gnk (we204600) ● pin connection ● grid assignment pin no. Connection pin no. 60 f2 59 nx 58 np 57 np 56 p1 55 p2 54 p3 53 p4 52 p5 51 p6 50 p7 49 p8 48 p9 47 p10 46 p11 45 p12 44 p13 43 p14 42 p15 41 p16 40 p17 39 p18 38 p19 37 p20 30 p27 29 p28 28 p29 27...

  • Page 38

    Ysp-1 38 ysp-1 ■ ic data ic304 : m30626fhpfp (dsp p.C.B) single-chip 16bit cmos microcomputer (main cpu) output (timer a): 5 input (timer b): 6 internal peripheral functions watchdog timer (15 bits) dmac (2 channels) d/a converter (8 bits x 2 channels) memory rom (1) ram (2) a/d converter (10 bits x...

  • Page 39

    Ysp-1 39 ic304 : m30626fhpfp (dsp p.C.B) single-chip 16bit cmos microcomputer (main cpu) no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 name po96 po95 po94 po93 po92 pi91 po90 byte cnvss po87 p...

  • Page 40

    Ysp-1 40 2 a b c d e f g h i j 1 3 4 5 7 6 ■ block diagram • see page 53 → schematic diagram input • see page 53 → schematic diagram input • see page 51, 52 → schematic diagram dsp • see page 54 → schematic diagram amp analog input pj2 pj3 ic26 ic27 ic311 tc40538p upc4570g2 ak5381vt-e2 tv l/r vcr l/...

  • Page 41

    Ysp-1 41 a b c d e f g h i j 1 2 3 4 5 6 7 ■ printed circuit board (foil side) 1 30 83 51 103 31 82 52 1 30 83 51 103 31 4 1 5 8 82 52 driver (tweeter) txn9 txp9 txn8 txp8 txn7 txp7 txn6 txp6 txn5 txp5 input (2) w8, w9 mgnd mgnd +15vm +15vm +3.3v gnd dsp cb1, cb2 nout0/2 gnd pc k0/2 nout1/3 gnd pc k...

  • Page 42

    Ysp-1 42 2 a b c d e f g h i j 1 3 4 5 7 6 ■ printed circuit board (foil side) dsp p.C.B. (side a) lead free solder used amp cb3 nout2 gnd pck2 nout3 gnd pck3 npwm_l gnd temp2 gnd pout2 nck2 gnd pout3 nck3 gnd ppwm_l amp_prt2 input (2) cb9 dest f an_out osd_clk m_r ts m_rxdo cnvss d a ux1 dgnd po w_...

  • Page 43

    Ysp-1 43 a b c d e f g h i j 1 2 3 4 5 6 7 dsp p.C.B. (side b) lead free solder used ■ printed circuit board (foil side) d305 f3 d306 f3 ref no. Location.

  • Page 44

    Ysp-1 44 2 a b c d e f g h i j 1 3 4 5 7 6 ■ printed circuit board (foil side) input (1) p.C.B. (side a) input (2) w6 dest temp3 (nc) f an_out (nc) osd_tx osd_clk osd_ce m_r t s m_cts m_rxdo m_txdo cnvss d a ux2 d a ux1 dv d gnd input (2) w7 v o l_det po w_r y pw_do wn /res +15vp s3.3bk s3.3 sw_out ...

  • Page 45

    Ysp-1 45 a b c d e f g h i j 1 2 3 4 5 6 7 input (1) p.C.B. (side b) lead free solder used 1 1 8 4 5 8 16 9 8 14 7 1 1 7 14 8 1 8 16 9 ■ printed circuit board (foil side) q19 h4 q20 h4 q22 c4 q23 d4 q24 c4 q25 d4 ref no. Location ic4 f4 ic26 c4 ic27 d4 ic39 e5 q8 d4 q9 e4 ref no. Location d16 h4 d17...

  • Page 46

    Ysp-1 46 2 a b c d e f g h i j 1 3 4 5 7 6 input (4) w12 gnd stby_sw s3.3 key1 kye0 dsp cb303 gnd +3.3v +15vp fl_ce fl_clk fl_txd fl_on remo t e s3.3 -24v fl40khz stby_sw key0 key1 front panel display remote control sensor input (2) p.C.B. (side a) ■ printed circuit board (foil side) input (3) p.C.B...

  • Page 47

    Ysp-1 47 a b c d e f g h i j 1 2 3 4 5 6 7 64 1 33 32 16 17 49 48 input (2) p.C.B. (side b) lead free solder used ■ printed circuit board (foil side) input (3) p.C.B. (side b) lead free solder used d15 f5 ic1 c5 q1 d6 q2 d6 q3 a6 q4 b6 q5 b6 q6 b6 q7 b6 q26 d6 ref no. Location input (4) p.C.B. (side...

  • Page 48

    Ysp-1 48 2 a b c d e f g h i j 1 3 4 5 7 6 input (5) p.C.B. (side a) ■ printed circuit board (foil side) input (2) w3 gnd gnd -24v +3.3v +3.3v +5v +15vm +15vm +15vm mgnd mgnd mgnd ac in input cb4 agmd +15v +5v +3.3v nc gnd s3.3 s3.3bk reset pw_down pow_ry switching power supply unit switching power ...

  • Page 49

    Ysp-1 49 a b c d e f g h i j 1 2 3 4 5 6 7 input (5) p.C.B. (side b) lead free solder used ■ printed circuit board (foil side) 1 16 32 17 d1 e6 d2 b4 d3 d5 d4 d5 d5 b4 d6 e6 d7 e6 d8 c4 d9 f6 ic7 b4 q13 d5 q14 e5 ref no. Location.

  • Page 50

    Ysp-1 50 ■ pin connection diagram ak4121vf 1 12 24 ak4381vt 1 8 16 ak5381vt 1 8 16 an77l04 1: in 3: com 2: out 9 1 bp5319f lc74781-9798 1 12 24 lc89057w-vf4-e 1 24 36 37 12 25 13 48 max3232cdwr 16 8 1 md3221n 32 16 1 mbm29lv160be 1 24 48 48 13 37 24 1 12 36 25 lc4032v-75tn48c tad108 m30626fhpfp 80 1...

  • Page 51

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n ysp-1 schematic diagram (dsp 1/2) 51 ★ all voltages are measured with a 10mΩ/v dc electronic volt meter. ★ components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed...

  • Page 52

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n ysp-1 schematic diagram (dsp 2/2) 52 ★ all voltages are measured with a 10mΩ/v dc electronic volt meter. ★ components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed...

  • Page 53

    Page 52 to dsp_cb303 h1 page 52 to dsp_cb300 b1 page 52 to dsp_cb302 g1 page 54 to amp_cb7 k3 page 54 to amp_cb7 k3 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 c1+ v+ c1 c2+ c2 v dout2 rin2 vcc gnd dout1 rin1 rout1 din1 din2 rout2 ic2: max3232cdwr on screen display controller 52 display controller segmen...

  • Page 54

    Dc/dc controller negative chpmp transducer h-bridge0 oscillator bios flagxn reference transducer h-bridge1 transducer h-bridge3 transducer h-bridge2 transducer h-bridge9 protection logic transducer h-bridge8 transducer h-bridge6 transducer h-bridge5 transducer h-bridge4 transducer h-bridge7 vvolmin4...

  • Page 55: Parts List

    Ysp-1 55 ysp-1 ■ warning ● components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. ●s印のある部分は、安全確保部品を示しています。部品の交換が必要な場合、パーツリストに記載されている部品を使用してください。 ●部品価格ランクは、予告なく変更することがあります。 abbreviations in this list are as fol...

  • Page 56

    Ysp-1 56 ysp-1 ✻ new parts * 新規部品 p.C.B. Dsp & p.C.B. Amp schm ref. Part no. Description remarks markets 部 品 名 rank % : ic3 (tms320c6713bgdp) and ic4 (tac8256) can not be supplied. When ic3 and ic4 are failures, please exchange dsp p.C.B. (we218400). %: ic3(tms 320c6713bg dp )及びic4(ta c8 256 )はパーツ供給...

  • Page 57

    Ysp-1 57 ysp-1 ✻ new parts * 新規部品 p.C.B. Amp & p.C.B. Input schm ref. Part no. Description remarks markets 部 品 名 rank * cb3 wa521800 cn.Bs.Pin 18p te FFCコネクタ cb4 lb918020 cn.Bs.Pin 2p ベース付ポスト 01 cb5 vl845500 cn.Bs.Pin 11p te ベースツキポスト 01 cb6 vl845500 cn.Bs.Pin 11p te ベースツキポスト 01 cb7 vl845000 cn.Bs.Pi...

  • Page 58

    Ysp-1 58 ysp-1 cb3 vb390100 cn.Bs.Pin 5p ベースピン 01 cb4 vb390700 cn.Bs.Pin 11p コネクタベースポスト 01 cb7 vb390800 cn.Bs.Pin 12p コネクタベースポスト 01 cb9 v6313500 cn.Bs.Pin 27p se FMNコネクタ− * cb10 vf283300 cn.Bs.Pin 15p コネクタベースポスト 01 * cb14 vl845600 cn.Bs.Pin 12p ベースツキポスト 01 cb19 vg879900 cn.Bs.Pin 2p ベースピン 01 c7 ur84...

  • Page 59

    Ysp-1 59 ysp-1 c102 ur837470 c.El 47uf 16v ケミコン 01 c104 ur857470 c.El 47uf 35v ケミコン 01 * s c105 we256400 c.Ce.Safty 0.1uf 275v 規格認定コン c107 ur837220 c.El 22uf 16v ケミコン 01 c110 ur838330 c.El 330uf 16v ケミコン 01 d1 vt332900 diode 1ss355 ダイオード 01 d2 vt332900 diode 1ss355 ダイオード 01 d3 vv833200 diode 1ss380 ...

  • Page 60

    Ysp-1 60 ysp-1 q14 vv556500 tr 2sa1037k q,r,s トランジスタ 01 q16 ic174020 tr 2sc1740s qrs トランジスタ 01 q19 vv655700 tr.Dgt dtc144eka デジタルトランジスタ 01 q20 vv655700 tr.Dgt dtc144eka デジタルトランジスタ 01 q21 vp872700 tr 2sc4488 s,t トランジスタ 01 q22 vv556400 tr 2sc2412k q,r,s トランジスタ 01 q23 vv556400 tr 2sc2412k q,r,s トランジスタ ...

  • Page 61

    Ysp-1 61 ysp-1 uf018100 c.El.Chp 100uf 6.3v チップケミコン 01 uf027220 c.El.Chp 22uf 10v チップケミコン 01 uf037100 c.El.Chp 10uf 16v チップケミコン 01 uf037470 c.El.Chp 47uf 16v チップケミコン 01 uf066220 c.El.Chp 2.2uf 50v チップケミコン 01 uf066470 c.El.Chp 4.7uf 50v チップケミコン 01 us035100 c.Ce.M.Chp 0.1uf 16v チップセラコン 01 us060700 c.C...

  • Page 62

    Ysp-1 62 ysp-1 ✻ new parts * 新規部品 chip parts schm ref. Part no. Description remarks markets 部 品 名 rank rd356360 r.Chp 3.6kΩ 1/16w チップ抵抗 01 rd356390 r.Chp 3.9kΩ 1/16w チップ抵抗 01 rd356470 r.Chp 4.7kΩ 1/16w チップ抵抗 01 rd356510 r.Chp 5.1kΩ 1/16w チップ抵抗 01 rd356560 r.Chp 5.6kΩ 1/16w チップ抵抗 01 rd356680 r.Chp 6....

  • Page 63

    Ysp-1 63 ysp-1 10mm hj35 1/4w type 5mm hf85 1/6w type hf45 1/4w type value 1/4w type part no. 1/6w type part no. 10 k Ω hf45 7100 hf45 7100 11 k Ω hf45 7110 hf45 7110 12 k Ω hj35 7120 hf85 7120 13 k Ω hf45 7130 hf45 7130 15 k Ω hf45 7150 hf45 7150 18 k Ω hf45 7180 hf45 7180 22 k Ω hf45 7220 hf45 722...

  • Page 64

    A b c d e 1 2 3 4 5 6 7 64 ysp-1 ■ exploded view 3-105 3-105 3-105 3-107 3-106 3-102 3-105 3-101 3-110 3-108 3-105 1-106 1-106 1-105 1-106 1-1 1-51 1-52 1-32 1-51 1-41 1-41 3-12 3-51 3-46 3-31 3-51 3-3 (3) 1-5 3-3 (4) 154 154 103 154 154 154 154 154 121 111 113 139 154 20 153 131 134 131 134 116 116...

  • Page 65

    Ysp-1 65 ■ mechanical parts * 1-1 wd832600 front panel フロントパネル * 1-5 wd832700 window/sheet j ウインドウ/シート * 1-5 wd705600 window/sheet ucrtkabgl ウインドウ/シート * 1-32 wd833200 button ボタン * 1-41 we203500 nonskid pad m10xt2 1pc 滑止パッド * 1-51 we237300 packing e パッキン e 01 * 1-52 we237300 packing a 510x4xt1 パッキン a...

  • Page 66

    Ysp-1 66 2 a b c d e f g h i j 1 3 4 5 7 6 ■ main unit 2-3 2-4 3-3 (2) 2-3 2-101 2-101 2-104 2-104 2-104 2-104 2-104 2-104 2-104 2-111 2-111 2-104 2-1-101 2-1-101 2-1-101 2-1-101 2-1-101 2-1-101 2-1-102 2-1-111 2-1-111 2-1-11 2-1-31 2-1-102 2-1-102 2-1-32 2-1-35 2-1-41 2-1-11 2-1-12 2-1-43 2-1-43 2-...

  • Page 67

    Ysp-1 67 ■ remote control ■ schematic diagram ic1: µ pd17243mc-240-5a4-e1-a p0e2 p0e3 rem vdd xout xin gnd resetpu p0d2 p0d3 p1b0/int p0e0 p0e1 p1a0 p1a1 p0c1 p0c0 p0b3 p0b2 p0b1 p0b0 p0a3 p1a2 p0d1 p0d0 p0c3 p0c2 p0a2 p0a1 p0a0 6 7 8 9 10 11 1 2 3 4 5 12 13 14 15 25 24 23 22 21 20 19 18 17 16 29 28...

  • Page 68: Ysp-1

    Ysp-1.