Yamaha YSP-3300 Service Manual

Summary of YSP-3300

  • Page 1

    P.O.Box 1, hamamatsu, japan service manual 1 0 1 2 5 2 '12.11 center unit ysp-cu4300/ysp-cu3300 wireless subwoofer ns-wsw160 digital sound projector ysp-4300/ysp-3300 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 the ysp-4300 consists of the ysp-cu4300 and ns-wsw160. The ysp-3300 consists of the ysp-cu3300 ...

  • Page 2: Draft

    This product contains chemicals known to the state of california to cause cancer, or birth defects or other reproductive harm. Do not place solder, electrical/electronic or plastic components in your mouth for any reason whatsoever! Avoid prolonged, unprotected contact between solder and your skin! ...

  • Page 3: Draft

    ■ system composition / システム構成 • the ysp-4300 consists of the ysp-cu4300 and ns-wsw160. • the ysp-3300 consists of the ysp-cu3300 and ns-wsw160. ・ ysp-4300 は、ysp-cu4300 および ns-wsw160 で構成 されています。 ・ ysp-3300 は、ysp-cu3300 および ns-wsw160 で構成 されています。 ▼ ysp-cu4300 ▼ ysp-cu3300 ▼ ns-wsw160 ▼ ns-wsw160 ysp-43...

  • Page 4: Draft

    ■ front panels ysp-cu4300 top view front view 4 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 5: Draft

    Ysp-cu3300 top view front view 5 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 6: Draft

    Ns-wsw160 front view side view 6 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 7: Draft

    ■ rear panels ysp-cu4300 rear view u, c, t, b, g, f models a, k, l, v, s, h models j model bottom view label 7 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 8: Draft

    T model a model k model b, g, f models labels u, c models ysp-cu4300 8 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 9: Draft

    J model l, h models v, s models 9 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 10: Draft

    Ysp-cu3300 rear view u, c, t, b, g, f models a, k, l, v, s, h models j model bottom view label 10 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 11: Draft

    Ysp-cu3300 t model a model k model b, g, f models labels u, c models 11 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 12: Draft

    J model l, h models v, s models 12 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 13: Draft

    Ns-wsw160 rear view u, c models 13 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 14: Draft

    T model a model k model b, g, f models 14 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 15: Draft

    H model s model l, h models j model v model 15 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 16: Draft

    ■ remote control panels fsr130 (j model) fsr130 (j model) fsr131 (u, c, t, k, a, b, g, f, l, v, s, h models) fsr131 (u, c, t, k, a, b, g, f, l, v, s, h models) ysp-cu3300 ysp-cu4300 16 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 17: Draft

    ■ amplifier section / アンプ部 rated output power / 定格出力 (1 % thd) subwoofer (100 hz) [ysp-cu4300] (4 ohms) ...............................124 w (62 w x 2) [ysp-cu3300] (6 ohms) .................................90 w (45 w x 2) tweeter (1 khz, 4 ohms) [ysp-cu4300] ...........................................

  • Page 18: Draft

    ■ wireless section / 無線部 band frequency / 周波数帯域 ...................................................................................... 2.4 ghz transmission range / 通信距離 (without interference / 妨害のないとき ) ....................................................................Approx. 20 m (66 ft) ■ genera...

  • Page 19: Draft

    Ns-wsw160 the “ ” logo and “intellibeam” are trademarks of yamaha corporation. 「インテリビーム」「intellibeam」は、ヤマハ株式会社の商標です。 the “ ” logo and “cinema dsp” are registered trademarks of yamaha corporation. 「シネマ dsp」「cinema dsp」は、ヤマハ株式会社の登録商標です。 “univolume” is a trademark of yamaha corporation. 「ユニボリューム」「univo...

  • Page 20: Draft

    51 (2") 79 (3-1/8") 30 (1-1/8") 161 (6-3/8") 160 (6-1/4") 86 (3-3/8") 99.5 (3-7/8") 1102 (43-3/8") 1008 (39-5/8") (with spacer / スペーサーを含む ) (without spacer / スペーサーを除く ) front view top view unit: mm (inch) 単位:mm(インチ) • dimensions / 寸法図 ysp-cu4300 manufactured under license from cambridge mechatronics...

  • Page 21: Draft

    908 (35-3/4") 1002 (39-1/2") 86 (3-3/8") 51 (2") 79 (3-1/8") 30 (1-1/8") 161 (6-3/8") 160 (6-1/4") 99.5 (3-7/8") (with spacer / スペーサーを含む ) (without spacer / スペーサーを除く ) front view top view unit: mm (inch) 単位:mm(インチ) ysp-cu3300 446 (17-1/2") 435 (17-1/8") 435 (17-1/8") 145 (5-3/4") 135 (5-3/8") 146 (5...

  • Page 22: Draft

    • set menu table / セットメニュー category menu sub-menu value [initial value] beam intellibeam beam+sound optimize beam optimize only auto setup sound optimize only horizontal front l angle front r center l90° to r90° surround l surround r beam travel front l length front r center 0.3 to 24.0 m / 1.0 to 8...

  • Page 23: Draft

    ■ internal view power (5) p.C.B. Power (2) p.C.B. Damp p.C.B. Power (7) p.C.B. Power (6) p.C.B. Digital p.C.B. Power (4) p.C.B. Input (1) p.C.B. Power (3) p.C.B. Fm tuner (ysp-cu4300) power (2) p.C.B. Awcd2a p.C.B. Input (3) p.C.B. Driver woofer input (4) p.C.B. Driver tweeters input (2) p.C.B. (ysp...

  • Page 24: Draft

    ■ service precautions / サービス時の注意事項 安全対策 ・ この製品の内部には高電圧部分があり危険です。修理 の際は、絶縁性の手袋を使用するなどの安全対策を 行ってください。 ・ 下記のコンデンサには電源を off にした後も電荷が残 り、高電圧が維持されており危険です。 修理作業前に放電用抵抗(5 k Ω /10 w)を下記の各コ ンデンサの端子間に接続して放電してください。 放電所用時間は各々約 30 秒間です。 ysp-cu4300/ysp-cu3300 power p.C.B. の c8、c44、c48 ns-wsw160 main p.C.B. の c23、c...

  • Page 25: Draft

    Bottom panel ボトムパネル ir bar b ir バー b rear cover リアカバー ir bar b ir バー b ir bar a ir バー a ir bar a ir バー a ① ① ① ① ② ③ ② ■ disassembly procedures / 分解手順 (remove parts in the order as numbered.) disconnect the power cable from the ac outlet. * length of the ir bar / ir バーの長さ ir bar a: 281.5 mm (11-1/8"...

  • Page 26: Draft

    Top panel トップパネル top frame トップフレーム cabinet l assembly キャビネット l ass'y cabinet r assembly キャビネット r ass'y damp p.C.B. Hook フック dgital p.C.B. Input (1) p.C.B. Cb908 cb906 cb703 cb3 cb9 ⑥ ⑤ ⑤ ⑤ ④ ④ ④ ④ ⑦ ⑦ ⑦ ⑦ fig. 2 3. キャビネット l ass'y の外し方 a. ④ のネジ 5 本を外します。(fig. 2) b. キャビネット l ass'y を外します。(fig. 2) 4. キャ...

  • Page 27: Draft

    Damp p.C.B. Power (1) p.C.B. Cb910 cb905 cb106 cb6 cb907 cb916 cb503 cb504 cb1 cb4 cb7 cb915 cb6 cb904 cb909 dgital p.C.B. ⑧ ⑨ ⑨ ⑨ ⑩ ⑩ input (1) p.C.B. Fig. 3 7. Damp p.C.B. の外し方 a. ⑧ のネジ 2 本、⑨ のネジ 7 本を外します。(fig. 3) b. Cb503、cb504、cb904、cb905、cb907、cb909、 cb910、cb915、cb916 を外します。(fig. 3) c. Damp p.C...

  • Page 28: Draft

    Input (1) p.C.B. Cb8 cb7 cb4 rear view digital p.C.B. ⑪ ⑫ ⑭ ⑬ ⑮ ⑮ 9. Input(1)p.C.B. の外し方 a. ⑪ のネジ 3 本、⑫ のネジ 2 本を外します。(fig. 4) b. Cb4、cb7、cb8 を外します。(fig. 4) c. Input(1)p.C.B. を外します。(fig. 4) 10. Digital p.C.B. の外し方 a. ⑬ のネジ 5 本、⑭ のネジ 2 本、⑮ のネジ 6 本を外 します。(fig. 4) b. Digital p.C.B. を外します。(fig. 4) 9. Rem...

  • Page 29: Draft

    Front panel unit フロントパネルユニット support サポート support サポート sp unit sp ユニット power (1) p.C.B. Power (2) p.C.B. Awcd2a p.C.B. Input (4) p.C.B. Cb4 cb7 cb7 cb915 cb916 input (1) p.C.B. Damp p.C.B. Cb905 cb907 cb904 cb909 ⑯ ⑱ ⑲ ㉓ ⑳ ㉑ ㉑ ㉒ ⑲ ⑱ ㉓ ㉓ ㉓ ⑰ ⑳ ㉒ 11. Power(2)p.C.B. の外し方 a. ⑯ のネジ 7 本、⑰ のネジ 2 本を外します。(fi...

  • Page 30: Draft

    14. ツィーターの外し方 a. ダンパー 4 個を外します。(fig. 6) ※ 外した古いダンパーは、空気漏れの原因となる恐 れがあるため、再利用できません。新しいものに 交換してください。 b. Sp キャビネットを外します。(fig. 6) c. ㉔ のネジ 2 本を外し、ツィーターを外します。 (fig. 6) ※ 他のツィーターも同様の方法で外すことができま す。 14. Removal of tweeters a. Remove the 4 dampers. (fig. 6) * the old damper, once removed, cannot be reused as ...

  • Page 31: Draft

    When checking the p.C.B.S: • put the rubber sheet and the cloth over this unit, and place the sub-chassis unit on them as shown below. (fig. 8) • connect the ground points of the power (1) p.C.B. (g2) to the chassis with a ground lead or the like. (fig. 8) • reconnect all cables (connectors) that ha...

  • Page 32: Draft

    Ruber sheet and the cloth ゴムシートと布 bottom grille assembly ボトムグリル ass'y dowel ダボ dowel ダボ dowels ダボ flatblade screwdriver マイナスドライバー metalblade ヘラ 1. Removal of driver a. Spread a rubber sheet and cloth for protection of this unit against any damage and place this unit on cloth with its bottom grille a...

  • Page 33: Draft

    Fig. 2 d. Remove 4 screws ( ① ), and pull out the driver. (fig. 2) e. Disconnect the connector connected to the terminal of the driver. (fig. 2) f. Remove the driver. (fig. 2) 2. Removal of rear panel assembly a. Remove 10 screws ( ② ). (fig. 2) b. Remove the rear panel assembly. (fig. 2) d. ① のネジ 4...

  • Page 34: Draft

    Dowel ダボ front panel assembly フロントパネル ass'y cabinet assembly キャビネット ass'y flatblad screwdriver マイナスドライバー metalblade ヘラ fig. 3 3. フロントパネル ass'y の外し方 ※ フロントパネル ass'y はダボでキャビネット ass'y に固定されています。取り外しの際、キャビネッ ト ass'y に傷が付かないよう十分注意してくださ い。 a. マイナスドライバーを 2 箇所のダボ位置へ差し込み、 フロントパネル ass'y をフロント側へ押します。 (fig. 3) ...

  • Page 35: Draft

    Fig. 4 4. Awcd2a p.C.B. の外し方 a. ③ のネジ 1 本を外します。(fig. 4) b. フックを外します。(fig. 4) c. Cb501 を外し、awcd2a p.C.B. を dsp(2)p.C.B. と一 緒に外します。(fig. 4) ただし、dsp(2)p.C.B. は dsp(1)p.C.B. に基板対基 板コネクターで直接接続されています。 4. Removal of awcd2a p.C.B. A. Remove screw ( ③ ). (fig. 4) b. Release hook. (fig. 4) c. Remove cb501 and...

  • Page 36: Draft

    When checking the p.C.B.S: • spread the rubber sheet and the cloth. Then place the rear panel assembly on the cloth and check it. (fig. 5) • reconnect all cables (connectors) that have been disconnected. • when connecting the flexible flat cable, be careful with polarity. P.C.B. をチェックする場合には: ・ ゴムシート...

  • Page 37: Draft

    ■ updating firmware / ファームウェアのアップデート there are 3 types to write the firmware. Method / 方法 support models / 対応するモデル writing method using the usb storage device ysp-cu4300 usb フラッシュメモリーを使用して書き込む方法 writing method using the cd ysp-cu3300 cd を使用して書き込む方法 writing method using the pc (rs-232c) pc(rs-232c)を使...

  • Page 38: Draft

    ● required tools • usb storage device • firmware ysp2012-xxxx.Bin ● preparation 1. Download the latest firmware from the specified download source to the folder of the pc. 2. Copy the latest firmware from the pc to the root folder of the usb storage device. Note) when the latest firmware is copied t...

  • Page 39: Draft

    "volume +" key "volume +" キー front view top view usb storage device usb フラッシュメモリー usb jack usb 端子 " " (power) key " "(電源)キー fl display fl ディスプレイ fig. 1 fig. 2 fig. 3 ● operation procedures 1. Insert the usb storage device to the usb jack. (fig. 1) 2. While pressing the “volume +” key, connect the po...

  • Page 40: Draft

    Ysp-cu3300 when the following parts are replaced, the firmware must be updated to the latest version. Digital p.C.B. Flash rom (ic102) of hdmi/osd controller ● confirmation of firmware version and checksum before and after updating the firmware, check the firmware version and checksum by using the s...

  • Page 41: Draft

    Example of coaxial jack / coaxial 端子使用例 fig. 1 • optical cable (when optical jack is used) • digital audio pin cable (when coaxial jack is used) • firmware cd download the latest firmware from the specified download source and create the firmware cd. ・ 光ファイバーケーブル(optical 端子使用時) ・ デジタル音声ピンケーブル(coaxia...

  • Page 42: Draft

    "volume +" key "volume +" キー front view top view " " (power) key " "(電源)キー fl display fl ディスプレイ ● operation procedures 1. While pressing the “volume +” key, connect the power cable to the ac outlet. (fig. 2) the firmware update mode is activated and “play cdda!” is displayed. (fig. 2) 2. Play the fi...

  • Page 43: Draft

    Ns-wsw160 when the following parts are replaced, the firmware must be updated to the latest version. 下記の部品を交換した場合、ファームウェアを最新バー ジョンにアップデートする必要があります。 ● confirmation of firmware version and checksum before and after updating the firmware, check the firmware version and checksum by using the self- diagn...

  • Page 44: Draft

    Pin no.2 rxd pin no.2 rxd pin no.3 txd pin no.3 txd pin no.5 gnd pin no.5 gnd pin no.7 rts pin no.7 rts pin no.8 cts pin no.8 cts pin no.2 rxd pin no.2 rxd pin no.3 txd pin no.3 txd pin no.5 gnd pin no.5 gnd pin no.7 rts pin no.7 rts pin no.8 cts pin no.8 cts ● 必要なツール ・ ファームウェア書き込み用プログラム メインマイコンファーム...

  • Page 45: Draft

    Serial port (rs-232c) シリアルポート(rs-232c) rs-232c cross cable rs-232c クロスケーブル pc rear view of this unit / 本機の後面 flexible flat cable (9p) カード電線(9p) rs-232c conversion adaptor rs-232c 変換アダプター writing port / 書き込みポート (cb205 on main (3) p.C.B.) sw7 sw4 t dsp ucom t r ucom dsp r rs-232c conversion adaptor rs...

  • Page 46: Draft

    Fig. 3 select internal flash memory internal fl ash memory を選択します select the port of rs-232c 接続している rs-232c ポートを選択します ● operation procedures 1. Connect the power cable of this unit to the ac outlet. The power to this unit is supplied and the microprocessor is in the writing mode. 2. Start up flashsta...

  • Page 47: Draft

    5. [setting]をクリックし、通信速度の設定を行い ます。(fig. 5) 5. Click [setting], and set the baud rate. (fig. 5) fig. 5 4. [refer...]をクリックし、書き込むファームウェア を選択します。(fig. 4) ※ id、および mcu type は書き込みファイル選 択後、自動的に取り込まれます。(fig. 4) [ok]をクリックします。(fig. 4) 4. Click [refer...] and select the firmware name. (fig. 4) * the id and mcu ...

  • Page 48: Draft

    8. ファームウェアの書き込みが完了すると、以下の 画面が表示されます。(fig. 7) [ok]をクリックします。(fig. 7) 9. [exit]をクリックして flashsta.Exe を終了します。 (fig. 7) 8. When writing of the firmware is completed, the screen appears as shown below. (fig. 7) click [ok]. (fig. 7) 9. Click [exit] to end flashsta.Exe. (fig. 7) fig. 7 10. 本機の電源コードを ac コンセント...

  • Page 49: Draft

    Serial port (rs-232c) シリアルポート(rs-232c) rs-232c cross cable rs-232c クロスケーブル pc rear view of this unit / 本機の後面 flexible flat cable (9p) カード電線(9p) rs-232c conversion adaptor rs-232c 変換アダプター writing port / 書き込みポート (cb205 on main (3) p.C.B.) sw7 sw4 t dsp ucom t r ucom dsp r rs-232c conversion adaptor rs...

  • Page 50: Draft

    ● operation procedures 1. Connect the power cable of this unit to the ac outlet. The power to this unit is supplied and the microprocessor is in the writing mode. 2. Start up awcard_fw_update_xxx.Exe. The screen appears as shown below. (fig. 3) 3. Select the port. (fig. 3) rs232c select the port of ...

  • Page 51: Draft

    5. [setting]をクリックし、通信速度の設定を行い ます。(fig. 5) [ok]をクリックします。(fig. 5) [connected]をクリックします。(fig. 5) 5. Click [setting], and set the baud rate. (fig. 5) click [ok]. (fig. 5) click [connected]. (fig. 5) fig. 5 4. [...]をクリックし、書き込むファームウェアを選 択します。(fig. 4) ※ id、および mcu type は書き込みファイル選 択後、自動的に取り込まれます。 4. Click [....

  • Page 52: Draft

    6. [extension]をクリックし、アップデートエリア を選択します。(fig. 6) [ok]をクリックします。(fig. 6) 7. 書 き 込 ま れ る フ ァ ー ム ウ ェ ア の バ ー ジ ョ ン と チェックサムを確認します。(fig. 7) [start]をクリックして書き込みを開始します。 (fig. 7) 6. Click [extension] and select the update area. (fig. 6) click [ok]. (fig. 6) 7. Check the firmware version and checksum written. ...

  • Page 53: Draft

    8. ファームウェアの書き込みが完了すると、update result へ “ok” が表示されます。(fig. 8) 9. [exit]をクリックして awcard̲fw̲update̲ xxx.Exe を終了します。(fig. 8) 8. When writing of the firmware is completed, “ok” is displayed to update result. (fig. 8) 9. Click [exit] to end awcard_fw_update_xxx.Exe. (fig. 8) fig. 8 10. 本機の電源コードを ac コンセントから抜...

  • Page 54: Draft

    下記の部品を交換した場合、本機が正常に動作するため にシステムモデル名と仕向け先を eeprom に書き込む必 要があります。 ・ digital p.C.B. ・ digital p.C.B. の eeprom(ic703) when the following parts are replaced, the system model name and the destination must be written to the eeprom to have proper operation. • digital p.C.B. • eeprom (ic703) on digital p.C....

  • Page 55: Draft

    4. Digital p.C.B. の tp731(ic701 の 140 ピンと接続) と gnd をショートさせます。(fig. 2) 4. Short tp731 (connected to pin 140 of ic701) of digital p.C.B. And gnd. (fig. 2) fig. 2 dest write dgnd tp73 1 tp 800 dest write dgnd tp731 tp800 108 73 144 37 36 72 109 1 dgital p.C.B. Short point keys on the remote control / リ...

  • Page 56: Draft

    Keys on the remote control / リモコンキー 7. ショートしたピンを元の状態に戻します。 8. 再 び 電 源 を 入 れ、 バ ッ ク ア ッ プ ic(eeprom: digital p.C.B. の ic703)の初期化を行います。 6. リモコンの “戻る” キーを押すと、表示されてい る仕向けが書き込まれ、自動的に電源が切れます。 (fig. 4) ※ このとき、バックアップ ic(eeprom:digital p.C.B. の ic703)の初期化は予約状態になってい ます。 7. Be sure to return the shorted pins t...

  • Page 57: Draft

    ■ self-diagnostic function / ダイアグ(自己診断機能) this unit has self-diagnostic functions that are intended for inspection, measurement and location of faulty point. There are 26 main menu items, each of which has sub- menu items. Listed in the table below are main menu items and sub- menu items. Note: some...

  • Page 58: Draft

    No. Main menu no. Sub-menu c pon check 1 hdmi on 2 hdmi off 3 airwired on 4 airwired off 5 fl on 6 fl off 7 usb on (ysp-cu4300) 8 usb off (ysp-cu4300) 9 d4spj off a ir flasher on b ir flasher off d hdmi select 1 hdmi 1 2 hdmi 2 3 hdmi 3 4 hdmi 4 e hdmi audio 1 spdif 2 multi channel pcm 3 arc f usb t...

  • Page 59: Draft

    Display / 表示 sub-menu display サブメニュー表示 opening message / オープニング表示 (main menu / メインメニュー ) after a few seconds 数秒後 ● starting self-diagnostic function with this unit in the stand-by mode, press the keys on the remote control in the order as shown below. The self-diagnostic function mode is activated. ...

  • Page 60: Draft

    1 3 2 display / 表示 sub-menu display サブメニュー表示 opening message / オープニング表示 (main menu / メインメニュー ) after a few seconds 数秒後 keys on the remote control / リモコンキー ● starting self-diagnostic function in the protection cancel mode if the protection function works and causes hindrance to troubleshooting, cance...

  • Page 61: Draft

    ● display provided when self-diagnostic function started the display is as described below depending on the situation the last time the power to this unit is turned off. When there is no history of protection function: “1. Dsp thr” is displayed. “11. Vol 0” menu is displayed in a few seconds. When t...

  • Page 62: Draft

    ● history of protection function when the protection function has worked, its history is stored in memory as backup data. Even if no abnormality is noted while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has been stored. The history of t...

  • Page 63: Draft

    ● functions in self-diagnostic function mode in addition to the self-diagnostic function menu items, functions as listed below are available. • power off • input selection • master volume ● initial settings when self-diagnostic function started the following initial settings are used when starting s...

  • Page 64: Draft

    1-1. Master volume 0 (mute) 1-2. Master volume 1 (-96.5 db minimum volume) 1-3. Master volume 30 (-40 db) 1-4. Master volume 60 (-20 db) 1-5. Master volume 100 (0 db maximum volume) 1 1 . V o l 0 1 2 . V o l 1 1 3 . V o l 3 0 1 4 . V o l 6 0 1 5 . V o l 1 0 0 ● details of self-diagnostic function me...

  • Page 65: Draft

    2. Test signal * when this menu is selected, the master volume level is raised up automatically. The built-in noise generator of dsp outputs the test noise through the channels specified by using the sub-menu. 2. Test signal ※ このメニューを選択すると、マスター音量レベル が自動的に上がります。 dsp 内蔵のノイズ発生回路によって、サブメニュー で指定したチャンネルへテ...

  • Page 66: Draft

    3 . S w e e p 4 . M i c c h k 4. Mic check the signals input through the intellibeam microphone are output to all channels via a/d-d/a. 4. Mic check インテリビームマイクに入力された信号が a/d − d/a 経由で全てのチャンネルへ出力されます。 3. Sweep test ※ このメニューを選択すると、出力レベルが自動的 に 52(-8.0)に上がります。 アナログ入力端子へスイープ信号(20 hz 〜 2 khz、 450mvrms、スイープ...

  • Page 67: Draft

    6. Fl display check fl 表示とインジケーターの動作を確認します。 サブメニュー操作により、表示状態が以下のように 変わります。 6. Fl display check this menu is used to check operations of the fl display and indicators. Using the sub-menu, the display condition changes as shown below. Fl display and indicators / fl 表示とインジケーター 6-1. All segments on / 全セ...

  • Page 68: Draft

    7 1 . 2 3 2 d : o k 7 2 . 2 3 2 h : o k 7 3 . A w d : o k 7 4 . A w g : o k 7 5 . S w p o : o k 7. Loopback check rs-232c、airwired、サブウーファーのループバック チェックをします。 7-1. Rs-232c txrx data rs-232c データの送受信チェックを行います。 7-2. Rs-232c hard flow rs-232c ハードウェアフローポートの動作 チェックを行います。 7-3. Airwired uart airwired データの送受信チェ...

  • Page 69: Draft

    8. Device check 各デバイス間の通信とバスラインの接続をチェック します。 チェックは自動的に実行されます。エラーが検出さ れると、対応するエラーメッセージが下記のように 表示されます。 8. Device check this menu is used to check the communication and bus line connection between devices. The check is executed automatically. When an error is detected, the corresponding error message i...

  • Page 70: Draft

    9-2. Dc dc voltage protection value of speaker output dc: center channel normal value: 105 to 150 (reference voltage: 3.3 v = 255) * if dc becomes out of the normal value range, the protection function works to turn off the power. 9. Ad data check this menu is used to display the a/d conversion valu...

  • Page 71: Draft

    9-4. Input (analog) inp: power supply voltage +12a, +5a, fl, vp normal value: 97 to 147 (power is turned on/ charged ipod) 29 to 64 (ipod standby) (reference voltage: 3.3v=255) * if input becomes out of the normal value range, the protection function works to turn off the power. 9-5. Dsp dsp: power ...

  • Page 72: Draft

    9-8. Usb vbu: power supply voltage usb_vbus normal value: 94 to 178 (reference voltage: 3.3v=255) * if vbu becomes out of the normal value range, the protection function works to turn off the power. 9-8. Usb vbu: 電源電圧 usb̲vbus 正常値:94 〜 178 (基準電圧:3.3 v = 255) ※ vbu が正常値を外れるとプロテクションが 働き、電源が切れます。 9-9. ...

  • Page 73: Draft

    C. Pon check 電源制御をチェックします。 c. Pon check this menu is used to check the power supply control. C-1. Hdmi on the hdmi power supply control is set to on. Hdmi 電源コントロールが on に設定されます。 hdmi_pon1 (107 pin) : +3.3h on hdmi_pon2 (108 pin) : +5h on hdmi_pon3 (109 pin) : +1.2h on c-2. Hdmi off the hdmi power sup...

  • Page 74: Draft

    E. Hdmi audio hdmi in/out に入力されたオーディオ信号の経路を チェックします。 ※ “e-3. Arc” メニューでのチェックの前に、あらか じめ必ず audio return channel 機能に対応してい るテレビを接続してください。 e. Hdmi audio this menu is used to check the route of audio signal input to hdmi in/out. * before check using “e-3. Arc” menu, be sure to connect a tv monitor equippe...

  • Page 75: Draft

    G. Airwired test airwired rx/tx enable ポートの設定を行います。 g. Airwired test this menu is used to setup of airwired rx/tx enable port. F . U s b t e s t f . U s b t e s t f . U s b t e s t k . S l p o n h. Self inspection digital サービスでは使用しません。 i. Self inspection input サービスでは使用しません。 h. Self inspection digita...

  • Page 76: Draft

    L x . T i w x x x h l x . D 4 w x x x h l x . D c x x x h l x . A m p x x x h l x . I n p x x x h l x . D s p x x x h l x . H d m x x x h l x . A w x x x h l x . V b u x x x h l x . 2 6 v x x x h l x . U s i x x x h l x . N o p r t l. Protection history プロテクション履歴が表示されます。 ※ 図中の数値は参考例です。 プロテクション履歴は下記の...

  • Page 77: Draft

    M-1. History 1 / 履歴 1 m-2. History 2 / 履歴 2 m-3. History 3 / 履歴 3 m-4. History 4 / 履歴 4 m-5. History 5 / 履歴 5 m-6. History 6 / 履歴 6 m-7. History 7 / 履歴 7 m-8. History 8 / 履歴 8 m-9. History reset / 履歴消去 select this menu and press the “enter” key on the remote control. The history of power-off factor ...

  • Page 78: Draft

    O. Factory preset バックアップ ic(eeprom:main p.C.B. の ic706)の 初期化を予約/禁止します。 o. Factory preset this menu is used to reserve/inhibit initialization of the back-up ic (eeprom: ic706 on main p.C.B.). N. Rs-232c dbg サービスでは使用しません。 n. Rs-232c dbg not for service. N . D b g c i n . D b g s i i init inhi (initial...

  • Page 79: Draft

    Hdmi/osd (ic101 on digital p.C.B.) / hdmi/osd(digital p.C.B. の ic101) dsp (ic501 on digital p.C.B.) / dsp(digital p.C.B. の ic501) microprocessor (ic701 on digital p.C.B.) / マイコン(digital p.C.B. の ic701) destination / 仕向け先 u, c, t, k, a, b, g, f, l, v, s, h, j is displayed. リモコンの “決定” キーを押す度に、仕向け表示が変わ...

  • Page 80: Draft

    Q. Microprocessor information ファームウェアバージョン、チェックサムが表示さ れます。 チェックサムは、データを 8 ビットごとに加算して いき、4 桁の 16 進数で表記したものです。 ※ 図中の数値は参考例です。 q. Microprocessor information this menu is used to display the firmware version and checksum values. The checksum is obtained by adding the data at every 8-bit and expressing t...

  • Page 81: Draft

    ■ display data pin no. 22 nc 21 nc 20 nc 19 nc 18 nc 17 nc 16 nc 15 nc 14 nc 13 nc 12 nc 11 nc 10 nc 9 nc 8 nc 7 nc 6 nc 5 nc 4 np 3 np 2 nx 1 f1 connection pin no. Note: 1) f1, f2 ..... Filament pin 2) np ..... No pin 3) dl ..... Datum line pin 4) 11g ..... Grid 5) nx ..... No extend pin 6) lgnd .....

  • Page 82: Draft

    • anode connection 1g – 10g 11g d0 1-1 d1 2-1 d2 3-1 d3 4-1 d4 5-1 d5 1-2 d6 2-2 d7 3-2 d8 4-2 d9 5-2 d10 1-3 d11 2-3 d12 3-3 d13 4-3 d14 5-3 d15 1-4 d16 2-4 d17 3-4 d18 4-4 d19 5-4 d20 1-5 d21 2-5 d22 3-5 d23 4-5 d24 5-5 d25 1-6 – d26 2-6 s9 d27 3-6 s8 d28 4-6 s7 d29 5-6 s6 d30 1-7 s5 d31 2-7 s4 d3...

  • Page 83: Draft

    ■ ic data ic101: sii9573ctuc (digital p.C.B.) hdmi port processors * no replacement part available. / サービス部品供給なし ysp-cu4300 ysp-cu3300 cec a0 cbus/ hpd serial ports ddc0 73 78,82,86,90,94,99 10-17 20-27 28-35 39-46 47-54 57-64 1-6,161-171,174-176 136,137 ddc1 mobile hd control cbus0 cbus1 always-on ...

  • Page 84: Draft

    Pin no. Function name type i/o detail of function 12 r0x0- 13 r0x0+ 14 r0x1- tmds input hdmi receiver port 0 tmds input data pairs. 15 r0x1+ 16 r0x2- 17 r0x2+ 10 r0xc- tmds input hdmi receiver port 0 tmds input clock pair. 11 r0xc+ 22 r1x0- 23 r1x0+ 24 r1x1- tmds input hdmi receiver port 1tmds input...

  • Page 85: Draft

    Pin no. Function name type i/o detail of function 121 ws0_out/ dr0 lvttl output main port i2s word select output/dsd data right bit 0. 122 sck0/ ddck lvttl output main port i2s serial clock output/dsd clock output. 124 sdo_0/dl0 lvttl output main port i2s serial data 0 output/dsd data left bit 0 out...

  • Page 86: Draft

    System switching pins pin no. Function name type i/o detail of function 76 dsda0 80 dsda1 ddc i2c data for respective hdmi receiver port. 84 dsda2 lvttl schmitt open drain 5 v tolerant input/output 88 dsda3 these signals are true open drain, and do not pull to ground when power is not applied to the...

  • Page 87: Draft

    Control pins configuration pins cec pins pin no. Function name type i/o detail of function local configuration/status i2c clock. 66 cscl schmitt open drain 5 v tolerant input chip configuration/status is accessed via this i2c port. This pin is true open drain, so it does not pull to ground if power ...

  • Page 88: Draft

    Power and ground pins reserved pin pin no. Function name type i/o detail of function 19 38 avdd33 power 3.3 v tmds core vdd. 56 123 iovcc33 power 3.3 v i/o vcc. 173 101 sbvcc5 power 5.0 v local power from system. This pin requires a 10 ohms series resistor. 18 36 avdd13 power 1.3 v tmds receiver cor...

  • Page 89: Draft

    Ic302: bu94607arkv-e (digital p.C.B.) usb host wav/aac/wma/mp3 decoder lsi pin no. Port name function name i/o detail of function 1 resetx resetx i system reset terminal 2 test15 sclm o [test15] pull-up at 2.2k-ohms to vdd1 system power supply terminal (test pin) 3 test16 sdam o [test16] pull-up at ...

  • Page 90: Draft

    Pin no. Port name function name i/o detail of function 23 sd_do sd_do i sd card data in terminal 24 sd_clk sd_clk o sd card clock terminal 25 sd_di sd_di o sd card data out terminal 26 sd_cs sd_cs o sd card chip select terminal 27 dvss vdss – gnd terminal 28 fl_cs fl_cs o serial flash rom chip selec...

  • Page 91: Draft

    Ic501: d81yk113czkb400 (digital p.C.B.) dsp (digital signal processor) switched central resource (scr) 1024 kb l2 rom 256 kb l2 ram 32 kb l1 ram 32 kb l1 pgm aet c674x™ dsp microprocessor dsp subsystem system control peripherals jtag interface input clock(s) memory protection i/o protection power/sl...

  • Page 92: Draft

    Pin no. Function name type (1) pull (2) detail of function device reset and jtag g3 reset i emifa async chip select l4 amute0/ resetout o (3) ipd reset output. Multiplexed with mcasp0 mute output. J1 tms i ipu jtag test mode select j2 tdi i ipu jtag test data input j3 tdo o ipd jtag test data output...

  • Page 93: Draft

    Pin no. Function name type (1) pull (2) detail of function m14 ema_we_dqm[0] /uhpi_hint/axr0[15]/gp2[9] o ipu emifa write enable/data mask for ema_d[7:0] r7 ema_oe /uhpi_hds1/axr0[13]/gp2[7] o ipu emifa output enable n6 ema_wait[0]/ uhpi_hrdy/gp2[10] i ipu emifa wait input/interrupt external memory ...

  • Page 94: Draft

    Pin no. Function name type (1) pull (2) detail of function r6 spi0_somi[0]/eqep0i/gp5[0]/boot[0] i/o ipd spi0 data/slave-out-master-in p4 spi1_scs[0] /uart2_txd/gp5[13] i/o ipu spi1 chip select r4 spi1_ena /uart2_rxd/gp5[12] i/o ipu spi1 enable t6 spi1_clk/eqep1s/gp5[7]/boot[7] i/o ipd spi1 clock n5...

  • Page 95: Draft

    Pin no. Function name type (1) pull (2) detail of function inter-integrated circuit modules(i2c0, i2c1) r3 uart0_rxd/i2c0_sda/tm64p0_in12/gp5[8]/ i/o ipu i2c0 serial data boot[8] p3 uart0_txd/i2c0_scl/tm64p0_out12/gp5[9]/ i/o ipu i2c0 serial clock boot[9] n5 spi1_simo[0]/i2c1_sda/gp5[6]/boot[6] i/o ...

  • Page 96: Draft

    Pin no. Function name type (1) pull (2) detail of function t4 axr1[11]/gp5[11] i/o ipu mcasp1 serial data n3 axr1[10]/gp5[10] i/o ipu m1 axr1[9]/gp4[9] i/o ipd m2 axr1[8]/epwm1a/gp4[8] i/o ipd m3 axr1[7]/epwm1b/gp4[7] i/o ipd m4 axr1[6]/epwm2a/gp4[6] i/o ipd n1 axr1[5]/epwm2b/gp4[5] i/o ipd n2 axr1[...

  • Page 97: Draft

    Pin no. Function name type (1) pull (2) detail of function supply and ground f6 cvdd (core supply) pwr – 1.2-v core supply voltage pins g6 cvdd (core supply) pwr – g7 cvdd (core supply) pwr – g10 cvdd (core supply) pwr – g11 cvdd (core supply) pwr – h6 cvdd (core supply) pwr – h7 cvdd (core supply) ...

  • Page 98: Draft

    Pin no. Function name type (1) pull (2) detail of function l10 vss (ground) gnd – ground pins m6 vss (ground) gnd – m7 vss (ground) gnd – m10 vss (ground) gnd – m11 vss (ground) gnd – t1 vss (ground) gnd – t2 vss (ground) gnd – t15 vss (ground) gnd – t16 vss (ground) gnd – (1) i = input, o = output,...

  • Page 99: Draft

    Ic701: tmpm362f10fg (digital p.C.B.) 32-bit risc microprocessor * no replacement part available. / サービス部品供給なし etm swd ahb lite bus matrix nvic dma controller cortex-m3 flash (1mb) cg port wdt rtc 16bit timer sio/uart (4byte fifo) 10bit adc i2c/sio cec rmc kwup ssp smc ram (56kb) backup ram (8kb) boo...

  • Page 100: Draft

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w er on standb y / [stb y a w] / (ip od) stb y hdmi / [stb y cec] when appl y cur rent 1 pk6 dir_sdo2 i i cdda writing data input pk6/an14 2 pk7 ti_warng i+ hiz damp error detect input pk7/an15 p.U to +3.3d 3 avss avss mcu mcu mcu 4...

  • Page 101: Draft

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w er on standb y / [stb y a w] / (ip od) stb y hdmi / [stb y cec] when appl y cur rent 34 po2 dir_n_rst o o dir reset output po2/sclk6/tbaout/cts6n 35 po3 dsp1_n_cs o o dsp chip select output po3/int9/tbbout 36 po4 aw_mosi so so aw ...

  • Page 102: Draft

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w er on standb y / [stb y a w] / (ip od) stb y hdmi / [stb y cec] when appl y cur rent 65 txd8 – hiz hiz pc0/a0/txd8 66 rxd8 – hiz hiz pc1/a1/rxd8 67 sclk8 – hiz hiz pc2/a2/sclk8/cts8n 68 pc3 – hiz hiz pc3/a3 69 txd9 cec_check i hiz...

  • Page 103: Draft

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w er on standb y / [stb y a w] / (ip od) stb y hdmi / [stb y cec] when appl y cur rent 96 pf3 usb_flg i hiz usb excess current detect input (high side sw) pf3/tracedata2 97 pf4 usb_pon o o usb power control output pf4/tracedata3 98 ...

  • Page 104: Draft

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w er on standb y / [stb y a w] / (ip od) stb y hdmi / [stb y cec] when appl y cur rent 132 ain1 input_prt ad hiz protection input power voltage detect +12d/+5a/+30v pj1/ain1 (ad) 133 ain2 vbus_prt ad hiz protection usb power voltage...

  • Page 105: Draft

    Fm synthesizer general io switch gpio6 gpio5 gpio4 gpio3 gpio2 gpio1 gpio0 gpio11 ic_n xin xout testb sda scl irq_n gpio10 gpio9 gpio8 gpio7 7 6 5 3 2 1 32 30 28 27 26 21 16 19 13 15 22 12 9 audio interface (aif) sdsp mdsp2 pll clock generator microprocessor interface registers preset rom dvss 25 gp...

  • Page 106: Draft

    Pin no. Function name i/o ( * 1) detail of function 1 gpio5 is/o general-purpose i/o pins 2 gpio4 is/o these i/o pin are assigned to the digital audio pins (wck/bck/sdix/sdox) 3 gpio3 is/o with aifmd[3:0] register (5v tolerant) 4 dvss – gnd 5 gpio2 is general-purpose i/o pins 6 gpio1 is these i/o pi...

  • Page 107: Draft

    Ic501: r5f21266snfp (dsp p.C.B.) single chip 16-bit microprocessor * no replacement part available. / サービス部品供給なし r0h timers port p0 8 8 6 1 3 2 port p1 port p3 port p4 port p5 a/d converter (10 bits x 12 channels) system clock generation circuit xin-xout high-speed on-chip oscillator low-speed on-ch...

  • Page 108: Draft

    Ysp-cu4300 ysp-cu4300 apple mfi341s2162 ic305 usb_host ic302 bu94607arkv-e2 14.9344mhz xl302 usb apl_n_cs apl_n_rst spi_usb usb_n_cs usb_n_rst /int,mchng,ipl_err search,busy i2c_usb input selector fm tuner input analog coaxcial isel_cnt1,2 hdmi/osd ic101 sii9573ctuc xl101 27mhz ic102 serial rom w25q...

  • Page 109: Draft

    C3 c2 c1 l2 f1 r1 l3 c4 p2 pt p1 nc nc v1 v2 s3 s4 nc nc s2a s2b s1a s1b nc +26d dgnd c23 t1 d20 d1 q2 l4 l6 l7 regulator si-8008tfe si-8008tfe ic11 +12d +12d control ic fa5511n-d1-te1 ic1 c24 p-con regulator ic12 +3.3d +3.3d control ic mip2f40msscf ic2 p2 pt p1 nc v1 v2 v3 s1 s2a s2b s2c s3a s3b nc...

  • Page 110: Draft

    Ac in driver 2 3 1 yst ry1 f301 protection limiter d4,5 - + +b -b q7,9,13,20 r61 power amplifier q3-6,8,10-12,18 6 5 7 - + + - ic201a ic201b l.P.F -12db/oct h.P.F -12db/oct q1,d6 15v +b -b t2 l.P.F -6db/oct njm4580e njm4580e njm4580e ic202a ic505 dac pcm1781dbqr - + microprocessor r5f21266snfp ic503...

  • Page 111: Draft

    P.C.B. Main (2) p.C.B. Main (3) p.C.B. Main (1) p.C.B. Dsp (1) p.C.B. Dsp (2) p.C.B. Awcd2a t2 q1,2 regulator w5 q3-6,8,10-12,18 power amplifier p-con ope-amp ope-amp ±15 ±15 ±15 w5 cb23 w203 w206 cb101 cb601 cb501 m3.3v cb602 cb503 njm4580e njm4580e filter filter t301 d201 ic201 ic202 ic303 status ...

  • Page 112: Draft

    Cb704 cb101 cb102 cb103 cb104 cb105 ic101 ic707 ic305 ic501 ic303 w303 w301 ic504 ic103 ic106 ic1 04 ic703 ic70 1 ic502 ic30 1 ic503 cb503 cb504 ic507 ic302 ic302 ic703 ic106 digital (side a) input (1) (cb4) input (1) (cb8) input (2) (cb52) (ysp-cu4300) ysp-cu4300 ysp-cu4300 power (1) (w2) s3.3 dgnd...

  • Page 113: Draft

    Ic304 ic704 ic702 ic708 ic71 0 ic706 ic1 05 ic1 02 digital (side b) 1 3 5 4 1 3 5 4 3 4 1 5 8 1 9 16 9 8 16 1 1 4 8 5 1 4 8 5 1 4 8 5 ysp-cu4300 ysp-cu3300 a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 113 ref no. Location d114 e3 d116 b3 ic102 c4 ic105 b3 ic304 f3 ic702 e4 ic704...

  • Page 114: Draft

    Ic5 cb5 cb65 cb61 w63 cb1 cb7 ic3 jk1 jk2 cb9 cb3 cb8 jk3 ic4 ic6 ic9 ic7 ic1 cb4 ic2 cb6 cb51 ic52 cb52 ic51 cb73 cb72 ic72 ic61 ic71 input (1) (side a) input (2) (side a) input (4) (side a) input (3) (side a) digital (w301) digital (cb302) power (4) (w971) power (1) (w5) power (1) (cb7) ysp-cu4300...

  • Page 115: Draft

    Ic63 input (1) (side b) input (2) (side b) input (4) (side b) input (3) (side b) ysp-cu4300 20 1 11 10 ysp-cu4300 k, a, l, v, s, h, j models u, c, t, b, g, f models u, c, t, b, g, f models a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 115 ref no. Location d1001 c3 d1006 e3 d1008 ...

  • Page 116: Draft

    Cb905 ic902 ic917ic907 ic903 ic916 cb910 ic901 cb904 cb909 cb907 cb912 cb913 cb911 ic905 ic91 5 ic909 cb908 cb906 ic906 ic91 1 ic91 2 ic91 5 ic91 6 ic91 3 ic923 cb90 1 cb902 damp (side a) – + – + drivers digital (cb503) digital (cb504) powre (1) (w1) input (4) (cb65) power (1) (w3) (ysp-cu4300) inpu...

  • Page 117: Draft

    Ic908 ic910 ic920 ic921 ysp-cu4300 ysp-cu4300 damp (side b) 16 15 30 1 1 30 15 16 1 3 5 4 1 3 5 4 a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 117 • semiconductor location ref no. Location ic908 e5 ic910 h3 ic920 b3 ic921 c3 q1601 e5 q1606 h3 q1609 e5 q1610 h3 ysp-cu4300 ysp-cu3...

  • Page 118: Draft

    Ic2 ic3 ic7 ic4 ic6 cb2 cb3 cb1 w1 w2 w5 cb6 ic12 ic11 w3 cb4 cb7 power (1) (side a) ac in 5 k-ohms 10 w 5 k-ohms 10 w ysp-cu4300 +26d dgnd damp (cb913) (ysp-cu4300) damp (cb910) +26d dgnd dgnd +12d +26d digital (w303) digital (cb106) input (1) (cb6) input (3) (cb72) input (4) (w63) dgnd +26d dgnd d...

  • Page 119: Draft

    Ic8 ic1 ic9 ic5 power (1) (side b) 1 5 1 8 4 5 1 3 4 5 k r a t, k, a, b, g, f, l, h models u, c, t, k, a, b, g, f, l, v, s, h models a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 119 • semiconductor location ref no. Location d2 d3 d5 e4 d6 e4 d10 d3 d11 c3 d12 d3 d15 h3 d16 e3 d1...

  • Page 120: Draft

    Power (2) (side a) power (4) (side a) power (5) (side a) power (6) (side a) power (7) (side a) power (3) (side a) dgnd fl_f1 +30v fl_n_cs fl_mosi fl_f2 dgnd dgnd pwr_n_led fl_f2 fl_n_rst +3.3d fl_sck dgnd dgnd dgnd fl_f1 hdsur_led sdsur_n_led +30v input (1) (cb7) input (1) (cb3) input (1) (cb9) digi...

  • Page 121: Draft

    Cb901 w951 w971 w981 power (2) (side b) power (4) (side b) power (5) (side b) (side b) (side b) power (3) (side b) power (6) power (7) a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 121 • semiconductor location ref no. Location q901 c2 ysp-cu4300 ysp-cu3300 draft.

  • Page 122: Draft

    Cb503 cb504 cb501 cb502 cb602 cb601 ic502 ic506 ic505 ic503 ic508 ic504 ic50 1 dsp (1) (side a) dsp (2) (side a) main (3) (w201) main (3) (w206) uart_tx dgnd uart_rx reset_n sdti bclk +5v lrclk dgnd dgnd dgnd fschange chg_i uart_tx dgnd uart_rx reset_n sdti bclk +5v lrclk dgnd dgnd dgnd fschange chg...

  • Page 123: Draft

    Ic507 1 4 3 5 dsp (1) (side b) dsp (2) (side b) a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 123 ref no. Location d501 c3 d503 d4 d504 c4 d505 c4 d506 c3 ic507 c4 q501 c3 q502 c3 q503 c4 q504 d4 q507 d3 q509 b5 q510 c5 • semiconductor location ns-wsw160 draft.

  • Page 124: Draft

    W206 w203 w20 1 cb205 w204 cb206 w5b1 w5b2 w5b3 cb23 w2a w2b w9a cb308 cb307 w8a cb304 w5a3 w9b w8b w5a2 w5a1 ic3 cb301 ic303 cb302 main (1) (side a) main (2) (side a) main (3) (side a) main (4) (side a) sub-transformer dsp (1) (cb502) dsp (1) (cb503) dgnd tx +5v rst rx mode 3.3v sel0 gsel2 sig dgnd...

  • Page 125: Draft

    Ic202 ic20 1 main (1) (side b) main (2) (side b) main (3) (side b) main (4) (side b) 4 5 1 8 4 5 1 8 t, k, b, g, f models a b c d e f g h i j 1 2 3 4 5 6 7 ysp-cu4300/ysp-cu3300/ns-wsw160 125 ref no. Location d2 e4 d4 b4 d5 b4 d6 d4 d7 d4 d8 c4 d9 d3 d10 d3 d11 b3 d12 b2 d13 b2 d14 b3 d315 g3 d316 g...

  • Page 126: Draft

    R5f21266snfp 16 24 25 1 17 8 9 32 16 8 1 pcm1781dbqr r3112n421a-tr-f 1 3 4 5 rp130q181d-tr-f 1 2 3 4 rp132h331d-t1-fe 3 1 5 4 kia7805pi out com in njm4580e 8 4 1 njm2867f3-05 (te1) sii9573ctuc 1 44 45 89 88 132 133 176 tc7whu04fu 8 4 1 rp108j131d-t1-fe 1 5 bu94607arkv-e2 40 60 61 1 41 20 21 80 20 6 ...

  • Page 127: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 127 ysp-cu4300/ysp-cu3300/ns-wsw160 schematic diagrams ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those ori...

  • Page 128: Draft

    Ysp-cu4300/ysp-cu3300/ns-wsw160 a 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 128 digital 2/4 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally...

  • Page 129: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 129 ysp-cu4300/ysp-cu3300/ns-wsw160 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ...

  • Page 130: Draft

    Ysp-cu4300/ysp-cu3300/ns-wsw160 a 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 130 digital 4/4 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally...

  • Page 131: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 131 ysp-cu4300/ysp-cu3300/ns-wsw160 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ...

  • Page 132: Draft

    Ysp-cu4300/ysp-cu3300/ns-wsw160 a 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 132 input 2/2 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally i...

  • Page 133: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 133 ysp-cu4300/ysp-cu3300/ns-wsw160 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ...

  • Page 134: Draft

    Ysp-cu4300/ysp-cu3300/ns-wsw160 a 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 134 power 1/2 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally i...

  • Page 135: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 135 ysp-cu4300/ysp-cu3300/ns-wsw160 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ...

  • Page 136: Draft

    Ysp-cu4300/ysp-cu3300/ns-wsw160 a 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 136 dsp ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally install...

  • Page 137: Draft

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 137 ysp-cu4300/ysp-cu3300/ns-wsw160 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ...

  • Page 138: Draft

    • electrical component parts warning ● components having special characteristics are marked ⚠ and must be replaced with parts having specifications equal to those originally installed. ● ⚠ 印のある部分は、安全確保部品を示しています。部品の交換が必要な場合、パーツリストに記載されている部品を使用し てください。 ● 部品価格ランクは、予告なく変更することがあります。 ■ replacement parts l...

  • Page 139: Draft

    Digital * zd734900 p.C.B. Digital ysp-cu4300 PCB DIGITAL * zd724400 p.C.B. Digital ysp-cu3300 PCB DIGITAL * cb101-105 zd534300 cn.Hdmi 19p se HDMIコネクター cb106 vb390400 cn.Bs.Pin 8p コネクター 01 cb302 vb390100 cn.Bs.Pin 5p ysp-cu4300 コネクター 01 * cb503-504 wv304400 socket 23p 506smt ソケット * cb702 wr758400 cn...

  • Page 140: Draft

    Digital c173 us635100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c174 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c175 uf008220 c.El.Chp 220uf 4v チップケミコン 01 c176 wd758300 c.Ce.Chp 10uf 10v チップセラコン 01 c177 us663100 c.Ce.Chp 1000pf 50v チップセラコン 01 c178 us635100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c179 us662100 c.Ce.Chp 100pf ...

  • Page 141: Draft

    Digital c509-510 us635100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c511-512 us663100 c.Ce.Chp 1000pf 50v チップセラコン 01 c513-515 us635100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c516-518 us663100 c.Ce.Chp 1000pf 50v チップセラコン 01 c519 us635100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c520-521 us661180 c.Ce.Chp 18pf 50v チップセラコン 01 c523 us...

  • Page 142: Draft

    Digital and input ic103 x7741a00 ic njm2867f3-05(te1) 電源IC 02 * ic104 ye695a00 ic rp108j131d-t1-fe 電源IC ic105 x4063a00 ic tc7whu04fu ロジックIC ic106 x7741a00 ic njm2867f3-05(te1) 電源IC 02 ic301 yd216a00 ic pcm9211ptr IC 04 ic302 ye099a00 ic bu94607arkv-e ysp-cu4300 IC 08 ic303-304 x0199b00 ic tc74vhc157...

  • Page 143: Draft

    Input c1004 us064100 c.Ce.Chp 0.01uf 50v b uctbg チップセラコン 01 c1005 us135100 c.Ce.Chp 0.1uf 16v ysp-cu4300 チップセラコン 01 c1006 us064100 c.Ce.Chp 0.01uf 50v b uctbg チップセラコン 01 c1008 ur837100 c.El 10uf 16v ysp-cu4300 ケミコン 01 c1009-1010 us062220 c.Ce.Chp 220pf 50v b チップセラコン 01 c1014 ur837470 c.El 47uf 16v ケ...

  • Page 144: Draft

    Input c1080 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c1083 us063470 c.Ce.Chp 4700pf 50v b チップセラコン 01 c1084 uf038100 c.El.Chp 100uf 16v チップケミコン 01 c1085 wd758300 c.Ce.Chp 10uf 10v チップセラコン 01 c1086 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c1087 us061220 c.Ce.Chp 22pf 50v b チップセラコン 01 c1088 us135100 c.Ce.C...

  • Page 145: Draft

    Input and damp pj2 wg582700 jack.Pin 1p rj-1150+31-0h00 ピンジャック 01 pj3 wp079900 jack.Pin 2p msd-252v-04 ピンジャック 01 q1001 wd974200 tr 2sa1036kt146 p,q,r トランジスタ 01 q1002 vv556400 tr 2sc2412k q,r,s トランジスタ 01 q1003 ws625500 fet rzr020p01tl FET 01 * q1004 ww782200 tr.Dgt dtc023jubtl デジタルトランジスタ q1007 ww7823...

  • Page 146: Draft

    Damp c1604 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c1605 wd758100 c.Ce.Chp 22uf 6.3v チップセラコン 01 c1606-1607 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c1612 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c1614 wd758100 c.Ce.Chp 22uf 6.3v チップセラコン 01 c1617 us663100 c.Ce.Chp 1000pf 50v チップセラコン 01 c1618 us625100 c.Ce...

  • Page 147: Draft

    Damp c1706 wk004400 c.Ce.M.Chp 10uf 16v チップ積層セラコン 01 c1707-1708 us135220 c.Ce.Chp 0.22uf 16v チップセラコン 01 c1709 ws765300 c.Ce.Chp 1uf 35v チップセラコン 01 c1718 ws765300 c.Ce.Chp 1uf 35v チップセラコン 01 c1719-1720 wu447000 c.Ce.Chp 0.1uf 50v k チップセラコン 01 c1721 ws765300 c.Ce.Chp 1uf 35v チップセラコン 01 c1722 wg348100 ...

  • Page 148: Draft

    Damp c1826 us135100 c.Ce.Chp 0.1uf 16v ysp-cu4300 チップセラコン 01 c1827 us063330 c.Ce.Chp 3300pf 50v b ysp-cu4300 チップセラコン 01 c1828-1831 we773800 c.Ce.M.Chp 1uf 10v b ysp-cu4300 チップ積層セラコン 01 c1832 us135100 c.Ce.Chp 0.1uf 16v ysp-cu4300 チップセラコン 01 c1833 wh046600 c.Ce.M.Chp 47uf 16v ysp-cu4300 チップ積層セラコン 03 ...

  • Page 149: Draft

    Power * zd734300 p.C.B. Power ysp-cu4300 j PCB POWER * zd723800 p.C.B. Power ysp-cu3300 j PCB POWER * zd734400 p.C.B. Power ysp-cu4300 ucvs PCB POWER * zd723900 p.C.B. Power ysp-cu3300 ucvs PCB POWER * zd734500 p.C.B. Power ysp-cu4300 tkabgflh PCB POWER * zd724000 p.C.B. Power ysp-cu3300 tkabgflh PC...

  • Page 150: Draft

    Power c46 ws765300 c.Ce.Chp 1uf 35v チップセラコン 01 c47 us035100 c.Ce.Chp 0.1uf 16v b チップセラコン 01 c48 ws275900 c.El 2200uf 35v ケミコン 04 c49 wv675300 c.Ce.M.Chp 0.1uf 50v チップ積層セラコン c50 us065100 c.Ce.Chp 0.1uf 50v b チップセラコン 01 c52 ur819220 c.El 2200uf 6.3v ケミコン 01 c54 wv675300 c.Ce.M.Chp 0.1uf 50v チップ積層セラコン ...

  • Page 151: Draft

    Power ⚠ f1 wg410500 fuse 6a 125v jucvs ヒューズ 01 ⚠ f1 kb000690 fuse t2.5a 250v tkabgflh ヒューズ 01 ⚠ ic1 x7734a00 ic fa5511n-d1-te1 電源IC 04 ⚠ ic2 x8899a00 ic mip2f40ms 電源IC 04 ⚠ ic3-4 wp388200 phot.Cpl tlp781(d4-gr,f) フォトカプラ 01 ic5 yc411a00 ic njm2886dl3-05(te1) 電源IC ⚠ ic6-7 wp388200 phot.Cpl tlp781(d4-g...

  • Page 152: Draft

    Dsp * zd753800 p.C.B. Dsp PCB DSP cb501 v8875600 cn.Je 13p te JEコネクター 02 cb502 vb390300 cn.Bs.Pin 7p コネクター 01 cb503 vb390700 cn.Bs.Post 11p コネクター 01 cb504 vb389800 cn.Bs.Pin 2p コネクター 01 cb601 v9357000 cn.Je 19p te JEコネクター cb602 v8875300 cn.Je.Plug 13p se JEコネクタープラグ 01 c501 us135100 c.Ce.Chp 0.1uf 16...

  • Page 153: Draft

    Dsp and main q510 wc529400 tr ktc3875s y gr rtk トランジスタ 01 st601 v4040500 scr.Term m3 スクリューターミナル 01 xl501 wf997400 rsnr.Ce 20mhz セラミック振動子 02 xl502 ws190000 rsnr.Crys 24.576mhz dsx321g 水晶振動子 02 * zd753100 p.C.B. Main j PCB MAIN * zd753200 p.C.B. Main ucs PCB MAIN * zd753300 p.C.B. Main tkbgf PCB MAIN ...

  • Page 154: Draft

    Main d2 wr897300 diode rr264m-400tr ダイオード 01 ⚠ d3 wf300200 diode.Brg ts4b03g 4a 200v ブリッジダイオード 04 d4-5 ww783900 diode 1ss355vm ダイオード 01 ⚠ * d6-7 ws698200 diode.Zenr hzu15b3 trf-e ツェナーダイオード d8-11 ww783900 diode 1ss355vm ダイオード 01 d12-13 ws697400 diode.Zenr hzu12b2 trf-e ツェナーダイオード 01 * d14 v8045400 dio...

  • Page 155: Draft

    Main st204 v4040500 scr.Term m3 スクリューターミナル 01 sw201-202 v8448200 sw.Slide sssf114900 スライドスイッチ 02 sw203 vq751500 sw.Tact skhhlma010 タクトスイッチ 01 ⚠ * t301 ye664a00 trans.Sub j サブトランス ⚠ * t301 ye665a00 trans.Sub ucs サブトランス ⚠ * t301 ye666a00 trans.Sub tkbgflh サブトランス ⚠ * t301 ye667a00 trans.Sub a サブトランス ⚠ ...

  • Page 156: Draft

    Value 1/4w type part no. 1/6w type part no. 11 kΩ hf45 7110 hf45 7110 12 kΩ hj35 7120 hf85 7120 13 kΩ hf45 7130 hf45 7130 15 kΩ hf45 7150 hf45 7150 18 kΩ hf45 7180 hf45 7180 22 kΩ hf45 7220 hf45 7220 24 kΩ hf45 7240 hf45 7240 27 kΩ hj35 7270 hf85 7270 30 kΩ hf45 7300 hf45 7300 33 kΩ hf45 7330 hf45 7...

  • Page 157: Draft

    25 11 56 32 80 80 63 53 53 34 62 27 53 55 56 62 62 62 67 67 62 62 62 80 72 80 52 52 52 58 52 62 62 62 62 80 80 80 80 67 35 (a2) 56 52 7 34 52 54 31 54 63 63 63 28 54 59 65 36 37 37 36 53 59 54 63 24 52 63 63 63 61 54 29 65 59 65 59 65 52 61 66 64 61 52 52 69 61 60 61 69 22 61 51 51 54 54 63 35 (a1) ...

  • Page 158: Draft

    * 1 zd734300 p.C.B. Assembly power j PCB POWER * 1 zd734400 p.C.B. Assembly power ucvs PCB POWER * 1 zd734500 p.C.B. Assembly power tkabgflh PCB POWER * 2 zd734600 p.C.B. Assembly input jkaflvsh PCB INPUT * 2 zd734700 p.C.B. Assembly input uctbg PCB INPUT * 3 zd734800 p.C.B. Assembly damp PCB DAMP *...

  • Page 159: Draft

    25 11 56 63 32 63 80 80 63 53 53 34 62 52 62 62 62 27 53 61 61 62 62 62 62 62 67 67 62 80 72 80 52 52 58 52 62 62 62 62 80 67 80 35 (a2) 56 52 34 52 80 80 54 31 54 63 63 28 54 59 65 36 37 37 36 53 59 54 63 24 52 63 63 80 80 63 61 54 29 65 59 65 59 65 52 61 66 64 61 52 52 69 61 60 61 69 22 51 51 54 5...

  • Page 160: Draft

    * 1 zd723800 p.C.B. Assembly power j PCB POWER * 1 zd723900 p.C.B. Assembly power ucvs PCB POWER * 1 zd724000 p.C.B. Assembly power tkabgflh PCB POWER * 2 zd724100 p.C.B. Assembly input jkaflvsh PCB INPUT * 2 zd724200 p.C.B. Assembly input uctbg PCB INPUT * 3 zd724300 p.C.B. Assembly damp PCB DAMP *...

  • Page 161: Draft

    200 200-1 205 204 206 207 j model t, a, b, g, f, j models t, a, b, g, f, j models 208 209 203 202 u, c, t, l, v, s, h, j models 202 k, a, b, g, f models • accessories * 200 zd116300 remote control fsr130 f-bw7395 j リモコン * 200 zd116400 remote control fsr131 f-bw7396 uctkabgflvsh リモコン 200-1 wu579000 b...

  • Page 162: Draft

    207 208 200 200-1 205 204 206 209 203 j model t, a, b, g, f, j models t, a, b, g, f, j models ysp-cu3300 * 200 zd116500 remote control fsr132 f-bw7397 j リモコン * 200 zd116600 remote control fsr133 f-bw7398 uctkabgflvsh リモコン 200-1 wu579000 battery cover f71-7390-04000 電池蓋 04 203 we818100 optical cable ...

  • Page 163: Draft

    1-23 1-23 1-23 1-23 1-11 1-31 1-31 1-32 1-32 1-32 1-32 1-32 1-32 1-34 1-34 1-36 1-27 1-25 1-29 1-32 1-32 1-16 2-20 1-32 1-35 1-35 1-35 1-35 1-35 1-35 1-26 1-10 1-34 1-32 1-28 1-33 1-32 4 6 3 21 21 7 7 2 5 5 21 21 (2) (4) 1-1 (3) 1-1 (1) 1-1 1-2 1-7 1-1 1-6 1-4 1-3 • overall assembly ns-wsw160 a b c ...

  • Page 164: Draft

    * 1-1 zd753100 p.C.B. Assembly main j PCB MAIN * 1-1 zd753200 p.C.B. Assembly main ucs PCB MAIN * 1-1 zd753300 p.C.B. Assembly main tkbgf PCB MAIN * 1-1 zd753400 p.C.B. Assembly main a PCB MAIN * 1-1 zd753600 p.C.B. Assembly main lh PCB MAIN * 1-1 zd753700 p.C.B. Assembly main v PCB MAIN * 1-2 zd753...

  • Page 165: Draft

    C1 fb1 fb2 gnd gnd gnd c2 c5 u1 vdd pa7 vss xout xin ispsel 7 55 47 39 31 23 15 6 54 46 38 30 22 14 4 52 36 28 20 12 44 3 51 43 35 27 19 11 1 pa0 pb0 pb1 pb2 pb3 pb4 pb5 pb6 pb7 pa1 pa2 pa3 pa4 pa5 pa6 pa7 49 41 33 25 17 9 50 42 34 18 10 26 2 53 45 37 29 21 13 5 8 48 40 32 24 16 ispsel isp vi isp gn...

  • Page 166: Draft

    Key no. Layout key code key no. Key name key code fsr131 (u, c, t, k, a, b, g, f, l, v, s, h models) fsr130 (j model) 1 beam ビーム 78-c7 2 enhancer エンハンサー 78-cb 3 (standby/on) 電源 78-cc 4 hdmi1 hdmi1 78-4a 5 hdmi2 hdmi2 78-d0 6 optical 光デジタル 78-49 7 hdmi3 hdmi3 78-2a 8 hdmi4 hdmi4 78-41 9 analog アナログ 7...

  • Page 167: Draft

    C1 fb1 fb2 gnd gnd gnd c2 c5 u1 vdd pa7 vss xout xin ispsel 7 31 23 15 6 46 30 22 14 4 36 28 20 12 44 3 35 27 19 11 1 pa0 pb0 pb1 pb2 pb3 pb4 pb5 pb6 pb7 pa1 pa2 pa3 pa4 pa5 pa6 pa7 33 25 17 9 34 18 10 26 2 45 37 29 21 13 5 8 32 24 16 ispsel isp vi isp gnd vi isp gnd c3 d1 batt. X1 r2 r4 r3 option 1...

  • Page 168: Draft

    1 2 3 4 5 6 7 8 9 10 11 12 26 27 28 29 30 31 32 33 34 35 36 37 44 45 46 51 17 21 20 22 18 24 19 23 25 13 14 16 15 fsr132 key no. Layout key code ysp-cu3300 key no. Key name key code fsr133 (u, c, t, k, a, b, g, f, l, v, s, h models) fsr132 (j model) 1 beam ビーム 78-c7 2 enhancer エンハンサー 78-cb 3 (standb...

  • Page 169: Draft

    ■ advanced setup selectable item/adjustable range description menu turn on volume sets the volume level at power-on. Off* (not set), 1 to 70 max volume sets the maximum volume level. 1 to 99, max* (maximum) input lock enables/disables the input key on the front panel. On (disabled), off* (enabled) p...

  • Page 170: Draft

    Memo 171 ysp-cu4300/ysp-cu3300/ns-wsw160 y sp-cu430 0/y sp-cu330 0/ ns-wsw1 60 draft.

  • Page 171: Ysp-Cu4300/ysp-Cu3300

    Ysp-cu4300/ysp-cu3300 ns-wsw160 draft.