Ver. 150806 cnps10x optima (2011) user's manual intel socket lga 2011 v3/2011/1366/1156/1155/1151/1150/775 cpus amd socket fm2/fm1/am3+/am3/am2+/am2 cpu & apus to ensure safe and easy installation, please read the following precautions. Www.Zalman.Com.
2 .Com english 2. Specifications 1. Precautions 1) this cooler must be used with a 120mm fan. 2) avoid inserting objects or hands into the fan while it is in operation to prevent product damage and injuries. 3) do not ingest the thermal grease, and avoid its contact with skin and eyes. If contact is...
3 .Com english thermal grease 3. Components 1) common components thermal grease [zm-stg2m] loaging block nuts bolts double-sided tape backplate user's manual fan cooler side caps fan fixing clips amd clip 2) intel components 3) amd components - socket lga 2011 v3/2011/1366/1156 /1155/1151/1150/775 -...
4 .Com english 4. Installation requirements 1) space requirements 2) air guide removal 3) cooler orientation 4) cpu and ram interference check the cooler’s installation requires an unobstructed space of 85mm(width), 132mm(length), and 152mm(height), with the cpu as a central reference point. Please ...
5 .Com english 5. Installation a. Lga intel socket installation lastly, fasten the four screws to secure the clips (please go to page 8 for further instructions) partially unscrew the four bolts located on the base of the cpu cooler. Then, insert the intel clips between the base and the heatpipe cov...
6 .Com english 1 2 ② install the bolts to the backplate according to the socket type and secure them with side caps. ※ backplate is not needed for lga 2011 v3 / 2011 sockets. Socket 775 socket 1156/1155/1151/1150 socket 1366 take note of the orientation of the nuts and the side caps. X o caution ③ -...
7 .Com english x o caution please make note of the orientation of the loading block’s installation. ③ - ⓑ socket 775 installation peel off the loading block cover and attach it to the backplate with the sticky side facing the center of the backplate. Peel off one side of the double-sided tape and at...
8 .Com english attach the backplate assembly to the back side of the motherboard by aligning the nuts to the motherboard mounting holes. If you were unsuccessful at first attempt, you may continue with the installation without the double-sided tape as it is not a necessary component. Fasten the four...
9 .Com english ⑦ position the fan as low as possible. M/b ⑧ connect the cooler’s 4-pin connector to the motherboard’s cpu fan header. Lowering the fan helps to cool the components on the motherboard. Tip please make sure that pwm control mode is activated in the motherboard’s bios settings. Caution.
10 .Com english amd clip b. Amd socket installation ① partially unscrew the four bolts located on the base of the cpu cooler. Then, insert the amd clips between the base and the heatpipe cover, with the clips bent away from the heatsink. Caution ② install bolts to the backplate according to the sock...
11 .Com english ③ peel off the loading block cover and attach it to the backplate with the sticky side facing the center of the backplate. Caution please note that the sticky side of the loading block serves to attach the loading block to the backplate. Peel off one side of the double-sided tape and...
12 .Com english m/b ⑤ attach the backplate assembly to the back side of the motherboard by aligning the nuts to the motherboard mounting holes. If you were unsuccessful at first attempt, you may continue with the installation without the double-sided tape as it is not a necessary component. ⑥ apply ...
13 .Com english ⑧ position the fan as low as possible. M/b ⑨ connect the cooler’s 4-pin connector to the motherboard’s cpu fan header. Lowering the fan helps to cool the components on the motherboard. Tip please make sure that pwm control mode is activated in the motherboard’s bios settings. Caution.
