Summary of ZDI12010XA
Page 1
En user manual dishwasher zdi12010xa.
Page 2: Contents
Contents safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ...
Page 3
• the water inlet hose has a safety valve and a sheath with an inner mains cable. Warning! Dangerous voltage. • if the water inlet hose is damaged, imme- diately disconnect the mains plug from the mains socket. Contact the service to re- place the water inlet hose. Use • this appliance is intended t...
Page 4: Control Panel
Control panel 1 2 3 4 5 6 1 on/off indicator 2 programme marker 3 indicators 4 delay button 5 start button 6 programme knob indicators description washing phase indicator. Drying phase indicator. End indicator. Salt indicator. This indicator is off while the programme operates. Programmes programme ...
Page 5: Before First Use
Programme 1) degree of soil type of load programme phases duration (min) energy (kwh) water (l) 3) normal soil crockery and cut- lery prewash wash 50 °c rinses dry 195 1.02 11 4) all prewash 14 0.1 4 1) the pressure and the temperature of the water , the variations of the mains supply, the options a...
Page 6
Water hardness water softener adjustment german degrees (°dh) french degrees (°fh) mmol/l clarke degrees level 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 1 2) 1) factory position. 2) do not use salt at this level. How to adjust the level of the water softener 1. Make sure t...
Page 7: Daily Use
1 2 3 4 a 3 2 1 4 fill the rinse aid dispenser when the lens ( a ) is clear. To adjust the released quantity of rinse aid, turn the selector between position 1 (lowest quantity) and position 4 (highest quantity). Daily use 1. Open the water tap. 2. Turn the programme knob until the pro- gramme marke...
Page 8
3. Start the shortest programme with a rins- ing phase, without detergent and without dishes. 4. Adjust the water softener to the water hardness in your area. 5. Adjust the released quantity of rinse aid. Setting and starting a programme setting mode the appliance must be in setting mode to start a ...
Page 9: Hints And Tips
Hints and tips the water softener hard water contains a high quantity of miner- als that can cause damage to the appliance and bad washing results. The water softener neutralises these minerals. The dishwasher salt keeps the water softener clean and in good conditions. It is important to set the rig...
Page 10: Troubleshooting
Cleaning the filters 1 c b a 2 3 4 5 d 6 7 8 to remove filters ( b ) and ( c ), turn the handle counterclockwise and remove. Pull apart filter ( b ) and ( c ). Wash the filters with water. Remove filter ( a ). Wash the filter with water. Before you put the filter ( a ) back, make sure that there are...
Page 11
Alarm code problem • the start indicator flashes continuously. • the end indicator flashes 1 time intermittently. The appliance does not fill with water. • the start indicator flashes continuously. • the end indicator flashes 2 times intermittently. The appliance does not drain the water. • the star...
Page 12: Technical Information
• the quality of the detergent can be the cause. Dishes are wet • the programme is without a drying phase or with a low temperature drying phase. • the rinse aid dispenser is empty. • the quality of the rinse aid can be the cause. Refer to ‘hints and tips’ for other pos- sible causes. Technical info...
Page 13
13 www.Zanussi.Com.
Page 14
14 www.Zanussi.Com.
Page 15
15 www.Zanussi.Com.
Page 16: 56970840-A-362013
Www.Zanussi.Com/shop 1 56970840-a-362013.