Zanussi ZGF 782 Instruction Booklet - Important Safety Information

Summary of ZGF 782

  • Page 1

    2 gas hob model zgf 782 instruction booklet please read this instruction booklet before using the appliance.

  • Page 2: Important Safety Information

    3 important safety information you must read hese warnings carefully before installing or using the hob. If you need assistance, contact our customer care department on 01635 521313 installation ● this hob must be installed by qualified personnel, according to the manufacturer’s instructions and to ...

  • Page 3: For The User

    4 this appliance complies with the following e.E.C. Directives: * 73/23 - 90/683 (low voltagedirective); * 93/68 (general directives); * 89/336 (electromagnetical compatibility directive); * 90/396 (gas appliances), and subsequent modifications guide to use the instructions the following symbols wil...

  • Page 4: Description of The Hob

    5 1. Hob top 2. Auxiliary burner 3. Semi-rapid burners 4. Ultra-rapid double-crown burner 5. Rapid burner 6. Ignition pushbutton 7. Control knob for front left burner (auxiliary) 8. Control knob for back left buner (semi-rapid) 9. Control knob for central burner (ultra-rapid) 10. Control knob for ba...

  • Page 5: Operation

    6 operation hob burners to light a burner, push the relevant control knob in, turn it anticlockwise to maximum position, and depress the ignition pushbutton marked by a small electric spark symbol. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and t...

  • Page 6: The Hob Top

    7 before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top using a soft cloth well wr...

  • Page 7: Something Not Working?

    8 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local zanussi service force centre. Symptom ■ there is no spark when lighting the gas ■ the gas ring burns unevenly solution ◆ check that the unit is plugged in and the electric...

  • Page 8: Peace of Mind For 24 Months

    9 zanussi guarantee conditions we, zanussi, undertake that if, within 24 months of the date of the purchase, this zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same free of any char...

  • Page 9: Engineer Technical Data

    10 overall dimensions width: 680 mm. Depth: 510 mm. Height: 72 mm. Weight: 12 kg. Cut out dimensions width: 560 mm. Depth: 480 mm. Thickness: 30 mm. Ignition ht spark spark generator ispra control's bf 50066 - 240v 0.6 ya t 120 spark gap fixed rear left burner (semi rapid) heat input 2.0 kw (6824 bt...

  • Page 10: Location

    11 installation guidance instructions clearances required when fitting the gas hob without a cooker hood above installation guidance instructions clearances required when fitting the gas hob with a cooker hood above 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm 650 mm 400 mm 400 mm 100 mm 50 mm 50 m...

  • Page 11: Gas Connection

    12 rectangular cut-out size for hob a) end of shaft with nut b) washer c) elbow it is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Fo 0814 gas connection conn...

  • Page 12: Building In

    13 on/off switch flex outlet on/off switch flex outlet fo 0763 fo 0764 30 20 min 60 a b fo 1013 1 2 3 50 50 fo 2039 fo 0199 a fitting the hob into the worktop carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on th...

  • Page 13: Electrical Connections

    14 electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observed....

  • Page 14: Wiring Diagram

    15 a. Ignitor switch b. Ignitor unit b l n 0 1 2 3 4 5 6 220/240 a wiring diagram.

  • Page 15: Fault Finding

    16 fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on Ω (ohms) x 1 scale and adjust zero if necessary. A) test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (ohm),...

  • Page 16

    17 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer adjusted light burner manual...

  • Page 17: Commissioning

    18 commissioning when the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - turn the gas tap to the max position and ignite. - set the gas tap to the min flame position then turn the control knob from min to max several ti...

  • Page 18: Servicing

    19 a: removal of hob top 1. Remove all control knobs, pan supports, burner caps and burner crowns. 2. Remove 2 screws for each burner. 3. Remove 6 fixing screws from the pan support hinges, and remove the hinges from the hob. 4. Lift hob top at the rear and disengage it from the front locators. B: r...

  • Page 19

    20