Zelmer 377 User Manual - page 24
26
Hint
Information on the product and hints on its use
The appliance is intended for domestic use. In case
●
it is used for food business purposes, the warranty
conditions shall change.
Unplug the appliance after operation.
●
Use a soft brush to wash the metal parts especially the
●
sieve with the sharp grinding disc.
Do not wash metal parts in the dishwasher. Aggressive
●
detergents used in the dishwasher cause these parts
to darken. Wash them manually using traditional
dishwashing liquids.
Before the first use, wash thoroughly all elements of
●
the equipment.
Juice extractor assembly
(Fig. C)
1
Insert the bowl on the motor so that the groove fits into
the slit of the motor housing.
2
Insert the sieve on the driver, press until stop and check
if it is correctly inserted and it turns easily.
3
Insert the lid on the bowl.
4
Lift both clamps and insert the fastenings in the openings
of the lid.
5
Press the clamps to the housing (you will hear
a characteristic click).
6
Place an appropriate utensil under the groove discharge.
Start up and operating
the juice extractor
(Fig. D)
Check if the switch is in the “0” position.
●
Unwind a sufficient length of the cord. The remaining
●
cord can be stored in the housing. Put the remaining
cord in the housing through the opening situated at the
side of the juicer.
1
Plug in the appliance and switch it on.
2
Place the product to be processed into the feeding tube
and gently press with the pusher.
After operation
(after extracting the juice)
(Fig. E)
1
Switch off the appliance.
2
Unplug the appliance.
Dismantle the parts – as in the case of the initial wash.
●
Maintenance
After you have finished clean the juice extractor
●
thoroughly to avoid the residue drying out.
The motor base housing should be cleaned with a wet
●
cloth and a small addition of a washing-up liquid.
Use a brush to clean the strainer, clean it in a running
●
water. Cleaning this part with your hand may result in skin
injury.
Do not use metal brushes to clean the strainer basket.
●
The other components (juice bowl, cover and food
●
pusher) should be cleaned after finishing the work in
a lukewarm water with an addition of a washing-up
liquid. Rinse them and dry. These component may be
also cleaned in a dishwasher at max. 60°C (except the
strainer).
Do not use aggressive detergents, such as emulsions,
●
polishes, etc, as they may remove graphic symbols
(marking, signs, etc.).
Dirt entrapped in corners and holes should be removed
●
with a toothbrush or a bottle-brush.
Take care of transparent plastic components,
which are sensitive to shocks and falls and
may be damaged easily.
Technical data
The technical parameters are quoted on the nameplate of
the product.
Admissible time of non-stop operation
15 minutes
An interval between repeated operation
30 minutes
Noise generated by the appliance (L
WA
)
80 dB/A
The juice extractor type 377 is built in II class insulation
.
The juice extractor meets applicable norms requirements.
The appliance meets the requirements of the directives:
Low voltage electrical device (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) –2004/108/EC.
–
The product is marked with CE symbol on the nameplate.
Description
(Fig. A)
1
Motor base
2
On/Off button
3
Clamps
4
Clutch
5
Juice bowl
6
Strainer basket
7
Cover
8
Food pusher
Before operation
(Fig. B)
Before the first use, dismantle the juice
extractor, wash and dry the parts that have
contact with the processed product.
1
Place the motor on a hard, clean and dry surface near
the electrical outlet.
2
Grasp the clamps on both sides of the appliance and pull
them away from the motor housing.
3
Lift the clamps, release the lid and lower the clamps.
4
Take out the food pusher. Remove the lid and the bowl
together with the sieve.