Zelmer CK1500 User Manual - page 48
50
CK1500-001_v01
6
CK1500-001_v01
4
Close the lid (5).
5
Place the kettle on the base
(4)
. Plug the kettle to
a socket provided with an earth pin.
6
Switch on the kettle by pushing button (10) – the LCD
display (7) will turn blue and the
icon will flash. After
some time the illumination will go out (the
icon will keep
flashing). The kettle will switch off automatically after boiling.
7
The kettle has three functions:
boiling water
, keep warm and boiling time . The
selected mode is displayed on the LCD display (7). Func
-
tions can be changed using the boiling program selection
button (8). During boiling, the LCD display will turn blue, and
the icon of the selected function will appear on the display.
8
Default settings: boiling water to 100°C, the keep warm
function in on.
When setting boiling parameters, water temperature may
be adjusted from 40°C to 100°C (each time the button is
pressed the temperature changes by 5°C). The temperature
setting may be changed by pressing the settings buttons
(9). The selected boiling temperature is shown on the LCD
display.
9
When setting the keep warm temperature, water tempe-
rature may be set between 40°C and 90°C, if the previous
temperature setting was 100°C. If boiling temperature was
set for example to 50°C, the keep warm temperature may be
set from 40°C to 50°C (each time the button is pressed the
temperature changes by 5°C). The set temperature may be
changed by pressing the settings buttons (9). The maximum
duration of the keep warm function is 60 minutes. In order
to switch off the keep warm function, set this parameter to
«00».
When the keep warm function is on, the kettle
boils water to the preset temperature (the
icon flashes) and then switches to the preset
keep warm temperature (the icon flashes).
10
When setting the water boiling time, it may be set from
3 to 6 seconds. The water boiling time may be changed by
pressing the settings buttons (9).
This setting is effective only when the water
boiling temperature exceeds 95°C.
11
When finished programming the settings, press button
(10). When in the operation mode, the operation function
icon flashes; the selected water temperature is shown on
the LCD display. When heating starts, a blue light comes on
inside the kettle. To go back to the settings mode, press but-
ton (10) button.
12
The appliance will switch off automatically after reaching
the set temperature. The light will go out.
During boiling or when the keep warm function
is on, if you lift the kettle off the base and put
it back on, all previous settings will be reset.
The appliance will automatically go back to
default settings (see
B
8
). To use the boiling
function or the keep warm function, select an
appropriate program again.
If water cools down, switch on the kettle again
to boil or heat water again.
If you plan to use the kettle again soon, it is not necessary
to remove the plug from the mains.
Make sure that the maximum kettle capacity is
not exceeded when the kettle is filled with water.
In the event that an empty kettle is switched on,
it will be switched off automatically by a thermal
device. In order to switch on the kettle again
after it cools down (approx. 15 minutes), lift it off
the base, fill with water, put the kettle back on
the base and switch on by pressing button (10).
Do not fill a hot kettle with cold water (and the
other way around).
When filling the kettle, avoid high temperature
differences.
Cleaning and maintenance
Always allow the kettle to cool down com
-
pletely before cleaning!
1
Unplug the kettle from the mains.
2
Remove the filter
(11)
and rinse it under running water.
3
Clean the outside surfaces with a soft damp cloth
and washing-up liquid.
In order to remove the build-up of hard water film from the
outside and inside walls of the kettle, wipe them with a damp
cloth and vinegar.
4
Rinse the kettle with fresh water and assemble the appli
-
ance only after all parts have been dried thoroughly.
Various black-coloured, rusty, milky, etc.
deposits may form inside the kettle and float
on the water. This is caused by minerals occur
-
ring naturally in water (calcium, magnesium,
iron, etc.). Such discoloration is not caused by
faulty operation of the appliance and does not
affect its use. In case of substantial accumula
-
tion of mineral deposits, proceed as described
in the “Descaling” section.
C
7
CK1500-001_v01
Descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. For this purpose use 6-10% vinegar
or citric acid.
●
Open the lid by pressing the lid release button
(6)
.
●
Pour in 0.5 l of vinegar (or add 40 g of citric acid) and fill
the kettle with water to the MAX level. Switch on the ket
-
tle.
●
Bring the mixture to boil and allow the kettle to stand for
30 minutes.
●
Empty the kettle and rinse it with fresh water.
●
Remove the filter
(11)
and rinse it under running water.
Replace the filter.
●
Fill the kettle with fresh water, boil the water and empty
the kettle.
●
Wipe any remaining limescale with a sponge and rinse
the inside of the kettle with water. Repeat the whole pro
-
cess in necessary.
The kettle should be descaled periodically
to avoid its possible damage.
Ecology – environment protection
Each user can protect the natural environment.
It is neither difficult nor expensive. In order to
do it: put the cardboard packing into recycling
paper container; put the polyethylene (PE)
bags into container for plastic.
When worn out, dispose the appliance to particular disposal
centre, because of the dangerous elements of this appli-
ance, which can be hazardous for natural environment.
Do not dispose into the domestic waste disposal!
The importer/manufacturer is not liable for any damages resulting
from improper use or handling of the appliance.
The importer/manufacturer reserves the right to modify the product
at any time and without prior notice in order to adjust it to valid law
regulations, norms, directives, or due to construction, trade, aesthetic
or other reasons.