Zelmer Solaris User Manual - page 47
53
5000-017_v02
2
Remove the inlet filter from the inlet filter casing.
3
Insert a new filter into the inlet filter casing (25) with the
fabric side directed towards the casing inner, take care that
the filter edges exactly adhere to the filter casing.
4
Slide the inlet filter casing (25) together with the filter in
the tracks until stop to the previous position.
Always replace a damaged inlet filter with
a brand new, original one.
Insert the SAFBAG dust bag module to the vacuum
●
cleaner chamber. Close the cover by pressing it until you
hear a characteristic click – pay attention not to trap the
dust bag.
HEPA OUTLET FILTER
The vacuum cleaners are equipped with a HEPA (High
Efficiency Particulate Air) H11, H13 outlet filter.
The filters have a high filtration capacity; they are made of
special fibers which are able to retain almost all dust particles.
The H11 and H13 classes determine the permeability of
a given filter: H11 filter retains 95.5% of particles with the
size of 0.3 micron and H13 filter retains as much as 99.95%
of all pollutants.
1
The HEPA outlet filter shall be replaced, when the filter
surface is dirty or the outlet filter exchange indicator light is
on (14) (pulsating red colour). The sound alarm for the outlet
filter exchange, so-called “Buzzer”, is on simultaneously with
the outlet filter exchange indicator light, also the vacuum
cleaner suction power is reduced (setting 1).
2
In order to exchange HEPA filter lift the vacuum cleaner
handle. Next, catch two protruding fasteners of the outlet
filter cover (1) pull strong the outlet filter cover with your
thumbs and lift it up. Slide the outlet filter cover out of the
vacuum cleaner.
3
Remove the HEPA filter case and replace it with a new
one. The HEPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
ACOUSTIC FOAM
1
In order to clean the acoustic foam (24) lift the vacuum
cleaner handle. Next, catch two protruding fasteners of the
outlet filter cover (1) pull strong the outlet filter cover (1) with
your thumbs and lift it up.
2
Slide the outlet filter cover (1) out of the vacuum cleaner.
Turn it and then remove the acoustic foam (24) out of the cover.
3
Has the acoustic foam (24) got dirty; it is possible to
rinse it under running water. Remember to dry the foam well
before reassembling.
It is absolutely not allowed to assemble not
completely dry acoustic foam in respect of
safety reasons.
4
Insert the rinsed acoustic foam (24) into previous
position. Insert the cover, so that the two protrusions located
in the bottom part of the cover, are directed into the holes in
the vacuum cleaner casing, press the outlet filter cover (1),
so that the hind fasteners get locked in the casing.
SAFBAG dust bag disassembly/assembly
F
1
The vacuum cleaner is equipped with a safety valve
which is located in the dust container (bag) chamber.
It opens automatically when the suction hose or the elements
attached to the suction hose are completely clogged or when
the dust bag is overfilled with dust. After the opening of the
valve a characteristic "fluttering" in the vacuum cleaner will
be heard. The opening of the safety valve will result in the
lighting of the dust bag full indicator.
2
When the dust bag full indicator (10) lights (with the
nozzle or the brush lifted above the cleaned surface) it means
that the bag is full and needs to be replaced. In addition the
dust bag full indicator may activate if the suction hose or the
elements attached to the suction hose are clogged.
3
Switch off the vacuum cleaner by pressing the on/off
button (7) and unplug the appliance.
4
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
5
Release the front cover fastening (15) and open the
cover.
6
Remove the SAFBAG dust bag module from the vacuum
cleaner chamber (22).
7
Shut the SAFBAG bag cover in order to cover the hole of
the soiled bag. While holding the bag plate, bend it upwards
and pull the bag out of the bag catch, guides.
8
Insert the plate of the new dust bag in the tracks of the
SAFBAG dust bag module (22) and slide it until stop. The
direction for inserting the dust bag is indicated by the arrow
on the bag.
Slide the SAFBAG dust bag module together with the
●
installed bag in the tracks located on the side of the
vacuum cleaner chamber. Close the cover by pressing it
until you hear a characteristic click – pay attention not to
trap the dust bag.
Do not vacuum without the SAFBAG dust bag
module installed in the appliance. The lack of
the SAFBAG dust bag module prevents from
locking the upper cover of the appliance.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the dust bag full indicator lights up,
b) the safety valve activates,
c) the vacuum cleaner operates poorly,
d) the dust bag is full.
E
D