1. DL manuals
  2. Zenith
  3. Monitor
  4. P50W26
  5. Installation And Operating Manual

Zenith P50W26 Installation And Operating Manual

Summary of P50W26

  • Page 2: Warning

    2 warning warning: to reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dang...

  • Page 3: Safety Instructions

    3 important safeguards for you and your new product your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and ob...

  • Page 4: Safety Instructions

    4 safety instructions 15. Lightning for added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the anten- na or cable system. This will prevent damage to the product due t...

  • Page 5: Contents

    5 after reading this manual, keep it in the place where the user can always contact easily. Warning 2 safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 step 1. Hook up monitor controls of the monitor . . . . . . . . . . . . . . . . . . . .6 watching external equipments...

  • Page 6: Controls of The Monitor

    6 controls of the monitor vol. Menu input select on/off main power button input select button volume ( f , g ) buttons power standby indicator illuminates red in standby mode, illuminates green when the monitor is turned on remote control sensor menu button d , e buttons y p b p r ( ) ( ) r (mono) r...

  • Page 7: Watching External Equipments

    7 watching external equipments connection to pc the monitor include only this d-sub 15 pin cable. Connection to av equipment y p b p r ( ) ( ) r (mono) r audio on/ off l r audio l ( ) ( ) l ac input (8 Ω ) external speaker av input component (dvd/dtv input) rgb1 output (pc/dtv output) lock remote re...

  • Page 8: Watching External Equipments

    8 - when connecting the plasma monitor with external equipments, match the colors of connecting ports (video - yellow, audio(l) - white, audio(r) -red). - connect the video input socket (yellow) with the bnc-rca adapter to the av input socket of the set. - if you have a mono vcr, connect the audio c...

  • Page 9

    9 - to watch digitally broadcast programs, purchase.Connect a digital set-top box. How to connect a user-supplied digital set-top box • connect dtv set-top ox video output to monitor component (dvd/dtv input) or to the monitor rgb1 (pc/dtv input) connector. • connect dtv set-top box audio outputs to...

  • Page 10

    10 resolution 640x350 720x400 640x480 800x600 horizontal frequency(khz) 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 45.913 53.011 64.062 35.156 37.879 48.077 46.875 53.674 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 90.03 100.04 120.00 56.25 60.31 72.18 75.00 85.06 o o o...

  • Page 11

    11 controls of the remote control - when using the remote control aim it at the remote control sensor of the monitor. 1 2 3 4 5 6 7 8 0 9 power sleep input select apc dasp arc pip arc pip twin picture swap menu mute ok vol power stop play ff rec rew p/still win.Size win.Position zoom + zoom - split ...

  • Page 12: Monitor Installation

    12 1. Make sure to secure the attachment stand to the dis- play platform using m8 bolts (commercially available) 25mm longer than the thickness of the platform. 2. Match the holes of monitor and stand. 3. Use the two (2) bolts provided to attach the stand to the monitor. Tighten each bolt securely i...

  • Page 13: Turning On The Monitor

    13 turning on the monitor - when using the remote control, aim it at its sensor on the monitor. Turning on the monitor just after installation turning on the monitor (power cord is still connected) 1. Connect power cord correctly. 2. Press the on/off button on the monitor. At this moment, the monito...

  • Page 14: Video Menu

    14 video menu - you can adjust picture contrast, brightness, color, sharpness and tint to the levels you prefer. - pip settings are not adjustable. 1. Press the menu button and then d / e button to select the video menu. 2. Press the g button and then d / e button to select the desired picture item ...

  • Page 15: Audio Menu

    15 audio menu 1.Press the dasp button to select the picture appearance setup. Dasp dasp (digital (digital auto sound processing) auto sound processing) 1. Press the menu button and then d / e button to select the audio menu. 2. Press the g button and then d / e button to select the desired sound ite...

  • Page 16: Time Menu

    16 time menu - timer function operates only if current time has been already set. - off-timer function overrides on-timer function if they are set to the same time. - the monitor must be in standby mode for the on timer to work. - to cancel off / on timer function press the d / e button to select of...

  • Page 17: Special Menu

    17 key lock key lock - the monitor can be set up so that it can only be used with the remote control. - this feature can be used to prevent unauthorized viewing. 1. Press the menu button and then d / e button to select the special menu. 2. Press the g button and then d / e button to select key lock ...

  • Page 18: Screen Menu

    18 auto auto adjustment (rgb1[pc] mode only) adjustment (rgb1[pc] mode only) - automatically adjusts picture position and minimizes image shaking. - although the image is still not correct, your monitor is functioning properly but needs further adjustment. - the auto config . And the manual config i...

  • Page 19

    19 manual configure (rgb1[pc] mode only) manual configure (rgb1[pc] mode only) - if the picture isn’t clear after auto adjustment and especially that characters are still trembling, adjust the picture phase manually. 1. Press the menu button and then d / e button to select the screen menu. 2. Press ...

  • Page 20: Pip Function

    20 w w atching pip atching pip - pip lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - when you select pc or dtv for main picture in pip, you can watch video, s-video or dvd for sub pi...

  • Page 21: Twin Picture

    21 selecting a source for the selecting a source for the t t win picture win picture twin picture press the pip input button to select the input mode for the sub picture. Main picture size main picture size adjustment adjustment press the twin picture button. • each press of twin picture button chan...

  • Page 22

    22 set id set id - use this function to specify a monitor id number. 1. Press the menu button and then d / e button to select the special menu. 2. Press the g button and then d / e button to select set id . 3. Press the g button and then f / g button to adjust set id to choose the desired monitor id...

  • Page 23

    23 transmission * [command 1] : k * [command 2] : to control pdp set. * [set id] : you can adjust the set id to choose desired monitor id number in special menu. See previous page. Adjustment range is 1 ~ 99. When selecting set id ‘0’, every connect- ed pdp set is controlled. * [data] : to transmit ...

  • Page 24

    24 09. Color (command:i) g to adjust the screen color. You can also adjust color in the video menu. Transmission data min : 0 ~ max : 64 * refer to ‘real data mapping1’. [k][i][ ][set id][ ][data][cr] acknowledgement data min : 0 ~ max : 64 [i][ ][set id][ ][ok][data][x] 10. Tint (command:j) g to ad...

  • Page 25

    25 13. Remote control lock mode (command:m) g to lock the front panel controls on the monitor and remote control. Transmission [k][m][ ][set id][ ][data][cr] acknowledgement data 0 : lock of 1 : lock on * if you’re not use the remote control, set this mode. When main power is on/off, remote control ...

  • Page 26

    26 25. Orbiter (command:p) g to control the orbiter function on/off. Transmission data 0 : orbiter off 1 : orbiter on [j][p][ ][set id][ ][data][cr] acknowledgement data 0 : orbiter off 1 : orbiter on [p][ ][set id][ ][ok][data][x] 26. White wash (command:q) g to control the white wash function on/o...

  • Page 27: Ir Code (Nec Format)

    27 g connect your wired remote control to remote control jack of the monitor. Set the control lock ‘on’ on the monitor back panel to work wired remote control. G output waveform single pulse, modulated with 37.917khz signal at 455khz g configuration of flame g repeat code g lead code • 1st flame low...

  • Page 28

    28 up ( d ) down ( e ) vol+ ( g ) vol- ( f ) power on/off power on power off mute number key 0 number key 1 number key 2 number key 3 number key 4 number key 5 number key 6 number key 7 number key 8 number key 9 aii input select rgb 1 rgb 2 (dvi input) video s-video component sleep ok ( Á ) menu das...

  • Page 29: Maintenance

    29 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, a...

  • Page 30: Troubleshooting Check List

    30 troubleshooting check list no output from one of the speakers • adjust balance in the audio menu. (refer to p.15) strange sound from the monitor • typical sound due to normal monitor operation, monitor is not faulty. No picture & no sound • check whether the monitor is turned on. • power cord ins...

  • Page 31: Product Specifications

    31 product specifications model width (inches / mm) height (inches / mm) depth (inches / mm) weight (pounds / kg) power requirement resolution color temperature (in operation) humidity (in operation) p50w26 48.2 / 1223 28.9 / 734 4.1 / 105 99.2 / 45 ac120v, 60hz 1280 x 720 (dot) 16,770,000 (256 step...

  • Page 32

    P/n : 3828va0352a (rf02ca) 206-3786.