1. DL manuals
  2. Zenith
  3. Projector
  4. Presentation PRO900X
  5. Installation And Setup Manual

Zenith Presentation PRO900X Installation And Setup Manual

Other manuals for Presentation PRO900X: Operating Manual, Technical Training Manual

Summary of Presentation PRO900X

  • Page 1

    Hd projection display installation and setup guide for system installer model pro900x presentation tm series ® presentation tm is a registered trademark of zenith electronics corporation.

  • Page 2: Safety Warnings

    Warning: to prevent fire or shock hazards, do not expose this product to rain or moisture. Note to cable/tv installer: this reminder is provided to call the cable tv system installer’s attention to article 820-40 of the national electric code (u.S.A.). The code provides guidelines for proper groundi...

  • Page 3: Contents

    P a g e 3 206-3634 contents safety warnings safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 installation overview installer’s experience level . . . . . . . . . . . . . . . . . . . 4 installation considerations . . . . . . . . . . . . . . . . . . . . 4 power cord requirements...

  • Page 4: Installation Overview

    3276-a p a g e 4 installer’s experience level the pro900x is a sophisticated entertainment machine tm . In addition to making the necessary connections, installation will most likely require a series of adjustments to ensure the projected image is not distorted. If these adjustments are not accu- ra...

  • Page 5: Specifications

    P a g e 5 3276-a specifications pro900x note: specifications are subject to change without prior notice. Optical projection system — crt; 7-inch high performance liquid cooled tubes, 5-inch active phosphor area, 90 degree deflection angle, super oxide cathodes. Lenses — high resolution color correct...

  • Page 6: Standard Connections

    3276-a p a g e 6 standard connections connecting computer video sources connect a video source such as a computer: pc, laptop, or notebook type. Connecting video and s-video sources connect video sources with a tuner, (vcr) or other video sources such as a dvd player or satellite receiver. To hook u...

  • Page 7: Standard Connections

    P a g e 7 3276-a standard connections connect or pin wiring reference.

  • Page 8: Connections / Control Panel

    3276-a p a g e 8 enter shows source/time display menu accesses on-screen menus power on indicator power on/off switch red, green, blue (rgb) horizontal/vertical input jacks composite video input composite video loop out jack (set loop switch to “out” if using loop through.) selects menu options remo...

  • Page 9: Remote Control

    P a g e 9 3276-a remote control red, green, blue setup notes • do not place heavy objects on top of the remote control keys. Prolonged unintentional operation of the remote shortens the usable life of the batteries. • remove the batteries if the remote control will not be used for a month or more. •...

  • Page 10: Product Overview

    P a g e 1 0 the pro900x hd projection display system is a high reso- lution multiple signal format display monitor. It uses 7” high performance liquid cooled crts. Each crt has a 5” active phosphor area and a 90 degree deflection angle. The crts use high-resolution color corrected multi-layered hybr...

  • Page 11: Rear View

    P a g e 1 1 3276-a vertical active - vertical deflection yoke drive is present in the 9-1510 module. Video enable - all conditions are ready for high voltage to turn on via the 9-1504 mo rear view be sure to read and understand the setup section before you attempt to install a pro900x system; you wi...

  • Page 12: Top / Inside View

    3276-a p a g e 1 2 top / inside view.

  • Page 13: Setup Remote Control

    P a g e 1 3 3634 the pro900x will be supplied with the mbr3470t and a universal customer remote control. For most servicing situ- ations the mbr3470t is required. The mbr3470t has the special functions needed for geometry/convergence adjust- ments and system setup functions which the universal cus- ...

  • Page 14

    1. When you enter the setup mode, the system is in the “geometry mode” (the shape controls adjust all three colors at the same time). To adjust an individual color (i.E. Red to adjust skew), you must press the “red select” key. This will put the system into the “convergence mode” (the shape controls...

  • Page 15

    I. Sync inputs there are three sync signal inputs for use with rgb sources: 1. Sync-on-green (sog) - - this is through the green video input bnc jack, terminated 75 ohms. 2. Horizontal/composite (h / comp) - - through a bnc jack on the 9-1515 combo module, software switchable termination 2k/75 ohms....

  • Page 16: Notes

    3276-a notes p a g e 1 6.

  • Page 17: Screen Size Selection

    Courtesy of draper shade & screen one of the most important decisions in screen selection is to determine the correct size of screen based upon- 1. The dimensions of the audience area. 2. The projection format, or formats, to be used. In some situations, these two questions yield the same answer; in...

  • Page 18

    3276-a p a g e 1 8 setup and alignment procedure procedure overview there are several situations to consider when performing the setup procedure for the pro900x system. The setup procedure will vary depending on the required physical and signal configuration. The simplest setup is that of a “factory...

  • Page 19: Setup References

    P a g e 1 9 3276-a setup references setup menus 9 - 1505 module 9 - 1510 module 9 - 1509 module top edge top view.

  • Page 20: Physical Setup

    3276-a examples of display setup distances and center points “a”* “b” screen projection display “peerless” width distance center mount center 48” 58 5/8” 26 3/8” 11” 60” 72 7/8” 30 3/4” 11” 80” 96 3/8” 38” 11” 96” 115 1/4” 43 5/8” 11” 120” 143 1/2” 52 3/8” 11” 144” 171 7/8” 61” 11” 160” 190 5/8” 66 ...

  • Page 21: System Alignment

    P a g e 2 1 3276-a system alignment mount bracket center 11" from front panel under the green crt center 11.

  • Page 22: System Alignment

    Iii. Preliminary alignment setup the following procedures are intended for complete “geometry/convergence” setup. Use the customer’s signal for doing phase, and size adjustments. You can use the internal pat- terns for shape and convergence if the customer signal sources do not have a cross-hatch pa...

  • Page 23: System Alignment

    Focus procedure. See the figure above. A. Turn on the projector, project a cross-hatch pattern on the screen. Cover up both the blue and red lenses. Work only on the green lens. B. Tighten all 4 lens mounting screws. C. Loosen all 4 lens mounting screws 3 full turns. D. Adjust the mechanical and ele...

  • Page 24: System Alignment

    System alignment p a g e 2 4 3276-a iv. Final detailed geometry/convergence setup use the video patterns generated by the customer’s signal source for final alignment. If this is not possible, use the internal cross hatch pattern only to do the geometry and convergence. The cus- tomer’s signal must ...

  • Page 25: System Alignment

    P a g e 2 5 3276-a system alignment 1. Size h. Size set to fill screen at c and d. (use external source not internal test pattern) 2. Size v. Size set to fill screen at a and b. (use external source not internal test pattern.) 3. Lin tb lr h. Lin l-r set equal widths cz=zd 4. Lin tb lr v. Lin t-b se...

  • Page 26

    3276-a p a g e 2 6.

  • Page 27: System Alignment

    P a g e 2 7 3276-a 1. Small h. & v. Statics set center of video for best overlap arrows with green (this may have to be ‘tweaked’ during this alignment procedure.) 2. Size h. Size set to match green at c and d. 3. Size v. Size set to match green at a and b. 4. Lin t-b l-r h. Lin l-r match green at c...

  • Page 28: Notes

    206-3634 © copyright 2000 zenith electronics corporation 1000 milwaukee avenue, glenview, illinois 60025-2495 notes.