Zenith PRO1200X Owner's Manual - Connections
Connections
3-1
206-3612 ZENITH PRO 1200X 151199
3
3
3
3
3
CONNECTIONS
CONNECTIONS
CONNECTIONS
CONNECTIONS
CONNECTIONS
ON
OFF
P O W E R / MA IN S
8 0 0 p e r i p h e r a l s
R
G
B
Com p-/H-S yncV -S ync
C O MM . P O R T
P O R T 3
P O R T 4 /5
V -nom
I-nom
Freq
S ee in stallatio n instructio ns b efore con nectin g to the su pp ly.
V oir la n otice d'in stallatio n av an t d e raccord er au réseau.
120/230 V
7/5 Amp
5 0 / 6 0 H z
S -V IDE O
OFF - ON
75 Ohm
V IDEO
gree n : operation
red : standby
PORT 2
P O R T 1
OFF - ON
75 Ohm
P R O J E C T O R MOD E
Th i s de v i c e c om pl i e s wi th p a r t 1 5 of
the FC C r ul e s . Op e r a ti on i s s u bj e c t to
fo l l o w i n g two co n d i ti o n s (1). Th i s
d e v i c e m a y n ot c a us e h a r m ful in te r -
fe r e n c e , a nd (2 ) th is de v ic e m u s t
a c c e p t a ny i n te r fe r e nc e r e c e i v e d
i nc l ud i ng i n te r fe r e nc e th a t m a y c a u s e
u nd e s i r e d o p e r a ti o n"
O N
O F F
P O W E R / M A I N S
V- n o m
I - n o m
F re q
120/230 V
7/5 Amp
50/60 Hz
AC Power (mains) Cord Connection
AC Power (mains) Cord Connection
AC Power (mains) Cord Connection
AC Power (mains) Cord Connection
AC Power (mains) Cord Connection
Use the supplied power cord to connect your projector to the
wall outlet. Plug the female power connector into the male
connector at the backside of the projector.
Review Safety Instuctions on AC Power on page 1-1.
Power Check
Power Check
Power Check
Power Check
Power Check
The power voltage is listed on sticker on the back side of the projector.
Warning !
Verify the power voltage corresponds to that of the wall outlet.
If the wall outlet voltage is different, call a qualified technician for power
adaptation of the projector.
Switching On/Off
Switching On/Off
Switching On/Off
Switching On/Off
Switching On/Off
The projector is switched ON and OFF using the power (mains) switch
ON/OFF.
Pressed : ON
Not pressed : OFF
The projector can start in the 'operational mode' (image displayed) or in
the 'stand by mode', depending on the position of the 'power up' dip
switch on the controller unit. This DIP switch must be set during
installation by a qualified technician. If you want to change this start up
mode, call a qualified technician.
Stand by indication lamp :
No light up : projector switched off
Green color : projector in Operational mode
Red color : projector is in Standby mode.
V IDEO
gre e n : operation
re d : s tandby
P O R T 1
O FF - O N
75 Ohm
P R O J E C T O R M O D E
Th is d e v ic e c o m p li e s w i th p a r t 1 5 o f
th e F C C r u l e s . O p e r a tio n i s s u b j e c t to
f o l l o w i n g t w o c o n d i t i o n s ( 1 ). Th i s
d e v ic e m a y n o t c a u s e h a r m fu l i n te r -
fe r e n c e , a n d (2 ) th is d e v i c e m u s t
a c c e p t a n y i n te r fe r e n c e r e c e iv e d
i n c l u d i n g i n te r fe r e n c e th a t m a y c a u s e
u n d e s i r e d o p e r a ti o n "
RS232 IN
R S2 32 O U TIR
REMOT E