1. DL manuals
  2. Abatron
  3. Recording Equipment
  4. BDI2000
  5. Installation Manual

Abatron BDI2000 Installation Manual

Manual is about: JTAG debug interface for GNU Debugger PowerPC 7440 / 7450 / 86xx

Summary of BDI2000

  • Page 1

    Bdi access jtag interface library mips32 installation manual manual version 1.00 for bdi2000 © 1992-2004 abatron ag.

  • Page 2

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 2 © copyright 1992-2004 by abatron ag v 1.00 1 introduction ................................................................................................................................. 3 1.1 bdi2000............................

  • Page 3

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 3 © copyright 1992-2004 by abatron ag v 1.00 1 introduction the bdiaccess library can be used to access the bdi2000 functions. With this library, a program run- ning on a windows/linux/unix host can take advantage of the jtag in...

  • Page 4

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 4 © copyright 1992-2004 by abatron ag v 1.00 2 installation 2.1 connecting the bdi2000 to target the cables to the target system are designed for the idt rc32300 development boards (optional available: part# 90070) and for ejtag...

  • Page 5

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 5 © copyright 1992-2004 by abatron ag v 1.00 bdi main / target a connector signals pin name describtion 1 dint ejtag debug interrupt ejtag 2.5: this output of the bdi2000 connects to the target dint line. Rc32300: this output of...

  • Page 6

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 6 © copyright 1992-2004 by abatron ag v 1.00 2.1.1 changing target processor type before you can use the bdi2000 with an other target processor type (e.G. Arm mips), a new setup has to be done (see chapter 2.5). During this proc...

  • Page 7

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 7 © copyright 1992-2004 by abatron ag v 1.00 2.2 connecting the bdi2000 to power supply 2.2.1 external power supply the bdi2000 needs to be supplied with 5 volts (max. 1a) via the bdi option connector (rev. A) or via power conne...

  • Page 8

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 8 © copyright 1992-2004 by abatron ag v 1.00 2.2.2 power supply from target system the bdi2000 needs to be supplied with 5 volts (max. 1a) via bdi main target connector (rev. A) or via target a connector (rev. B/c). This mode ca...

  • Page 9

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 9 © copyright 1992-2004 by abatron ag v 1.00 2.3 status led «mode» the built in led indicates the following bdi states: mode led bdi states off the bdi is ready for use, the firmware is already loaded. On the power supply for th...

  • Page 10

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 10 © copyright 1992-2004 by abatron ag v 1.00 2.4 connecting the bdi2000 to host 2.4.1 serial line communication the host is connected to the bdi through the serial interface (com1...Com4). The communication cable between bdi an...

  • Page 11

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 11 © copyright 1992-2004 by abatron ag v 1.00 2.4.2 ethernet communication the bdi2000 has a built-in 10 base-t ethernet interface (see figure below). Connect an utp (un- shilded twisted pair) cable to the bd2000. For thin ether...

  • Page 12

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 12 © copyright 1992-2004 by abatron ag v 1.00 2.5 installation of the configuration software on the enclosed diskette you will find the bdiaccess library, the bdi configuration software and the firmware required for the bdi. Cop...

  • Page 13

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 13 © copyright 1992-2004 by abatron ag v 1.00 2.6 bdi2000 setup/update first make sure that the bdi is properly connected (see chapter 2.1 to 2.4). The bdi must be con- nected via rs232 to the windows host. To avoid data line co...

  • Page 14

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 14 © copyright 1992-2004 by abatron ag v 1.00 2.6.2 windows hosts start the setup and demo program and press the setup bdi2000 button. The following dialogbox is used to check or update the bdi firmware and logic and to set the ...

  • Page 15

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 15 © copyright 1992-2004 by abatron ag v 1.00 subnet mask enter the subnet mask of the network where the bdi is connected to. Use the following format: xxx.Xxx.Xxx.Xxxe.G.255.255.255.0 a subnet mask of 255.255.255.255 disables t...

  • Page 16

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 16 © copyright 1992-2004 by abatron ag v 1.00 3 specifications operating voltage limiting 5 vdc ± 0.25 v power supply current typ. 500 ma max. 1000 ma rs232 interface: baud rates 9’600,19’200, 38’400, 57’600,115’200 data bits 8 ...

  • Page 17

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 17 © copyright 1992-2004 by abatron ag v 1.00 4 environmental notice disposal of the equipment must be carried out at a designated disposal site. 5 declaration of conformity (ce).

  • Page 18

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 18 © copyright 1992-2004 by abatron ag v 1.00 6 warranty abatron switzerland warrants the physical diskette, cable, bdi2000 and physical documentation to be free of defects in materials and workmanship for a period of 24 months ...

  • Page 19: Appendices

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 19 © copyright 1992-2004 by abatron ag v 1.00 appendices a troubleshooting problem the firmware can not be loaded. Possible reasons • the bdi is not correctly connected with the target system (see chapter 2). • the power supply ...

  • Page 20

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 20 © copyright 1992-2004 by abatron ag v 1.00 b maintenance the bdi needs no special maintenance. Clean the housing with a mild detergent only. Solvents such as gasoline may damage it. If the bdi is connected correctly and it is...

  • Page 21

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 21 © copyright 1992-2004 by abatron ag v 1.00 observe precautions for handling (electrostatic sensitive device) unplug the cables before opening the cover. Use exact fuse replacement (microfuse msf 1.6 af). 4 5 4.1 while holding...

  • Page 22

    Bdi access jtag interface library, bdi2000 (mips32) installation manual 22 © copyright 1992-2004 by abatron ag v 1.00 c trademarks all trademarks are property of their respective holders..