ABB A130-H57 Operation Manual - Figures

Operation Manual / 4 Product description / A130-H.. - A140-H

 Figures

© Copyright 2017 ABB. All rights reserved.

HZTL4030_EN

Revision D

May 2017

Figures

Fig. 1: Layout and function of the turbocharger ......  4

Fig. 2: Compressor wheel cooling ................................ 5

Fig. 3: Warning plate locations ....................................  6

Fig. 4: Locations of the rating plates .......................... 7

Fig. 5: Suspension of complete turbocharger unit..  8

Fig. 6: Removing the turbocharger.............................  9

Fig. 7: Loosening the clamping nut............................  11

Fig. 8: Putting down the turbocharger .....................  12

Fig. 9: Inserting gaskets into the bracket ................ 13

Fig. 10: Inserting the threaded rods .......................... 14

Fig. 11: Requirements for threaded rods .................. 14

Fig. 12: Placing the turbocharger on the bracket.... 15

Fig. 13: Preparing the clamping nut for the tighten-

ing procedure ................................................................  17

Fig. 14: Tightening pressure screws.......................... 18

Fig. 15: Connecting the compressor cooling air in-

take .................................................................................. 19

Fig. 16: Attaching the support .................................... 19

Fig. 17: Oil orifice ...........................................................  21

Fig. 18: Layout and overview of speed measurement

system ............................................................................  28

Fig. 19: Replacing the speed sensor .........................  30

Fig. 20: Noise insulation, bellows............................... 32

Fig. 21: Replacing the protective grid.......................  35

Fig. 22: Cleaning the filter silencer............................  40

Fig. 23: Compressor-end, non-rotating parts.........  42

Fig. 24: Turbine end, non-rotating parts .................  43

Fig. 25: Soaking the turbine end................................  46

Fig. 26: Weights of assemblies ..................................  59

Fig. 27: Removing air inlets.........................................  60

Fig. 28: Removing the gas outlet casing................... 61

Fig. 29: Removing the gas outlet flange ..................  63

Fig. 30: Removing the compressor casing ..............  64

Fig. 31: Dismantling the wall insert...........................  65

Fig. 32: Press off the casing......................................... 66

Fig. 33: Removing insulation sheets .......................... 67

Fig. 34: Oil orifice ........................................................... 67

Fig. 35: Removing cartridge group 1.......................... 68

Fig. 36: Removing cartridge group 2 ......................... 68

Fig. 37: Removing the nozzle ring ............................... 69

Fig. 38: Installing the cartridge group on the service

support ............................................................................ 70

Fig. 39: Measuring clearance A and B ......................... 71

Fig. 40: Nozzle ring compression PD ......................... 72

Fig. 41: Installing the nozzle ring ................................ 73

Fig. 42: Measuring the end position of the nozzle

ring ................................................................................... 74

Fig. 43: Lifting the cartridge group and rotating it

by 90° ............................................................................... 74

Fig. 44: Installing the cartridge group....................... 75

Fig. 45: Fitting the wall insert and the diffuser ....... 76

Fig. 46: Installing the compressor casing................. 77

Fig. 47: Measuring clearances N and R ...................... 78

Fig. 48: Installing the air inlets.................................... 79

Fig. 49: Installing the gas outlet flange..................... 80

Fig. 50: Installing the gas outlet casing .................... 80

Fig. 51: Tightening torques ......................................... 81

Fig. 52: Overview of part numbers ............................. 88

Page 

90

 / 

91

Page 

90

 / 

91