1. DL manuals
  2. ABB
  3. Relays
  4. REC650 ANSI
  5. Manual

ABB REC650 ANSI Manual

Manual is about: Relion 650 series Bay control

Summary of REC650 ANSI

  • Page 1

    Relion® 650 series — dnp, 650 series version 2.2 point list manual.

  • Page 3

    Document id: 1mrk 511 419-uus issued: october 2017 revision: a product version: 2.2.1 © copyright 2017 abb. All rights reserved.

  • Page 4

    Copyright this document and parts thereof must not be reproduced or copied without written permission from abb, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software and hardware described in this document is furnished under a license and...

  • Page 5

    Disclaimer the data, examples and diagrams in this manual are included solely for the concept or product description and are not to be deemed as a statement of guaranteed properties. All persons responsible for applying the equipment addressed in this manual must satisfy themselves that each intende...

  • Page 6

    Conformity this product complies with the directive of the council of the european communities on the approximation of the laws of the member states relating to electromagnetic compatibility (emc directive 2004/108/ec) and concerning electrical equipment for use within specified voltage limits (low-...

  • Page 7

    Table of contents section 1 introduction............................................................................3 this manual.............................................................................................. 3 intended audience............................................................

  • Page 8

    2.

  • Page 9

    Section 1 introduction 1.1 this manual guid-ab423a30-13c2-46af-b7fe-a73bb425eb5f v18 the point list manual describes the outlook and properties of the data points specific to the ied. The manual should be used in conjunction with the corresponding communication protocol manual. 1.2 intended audience...

  • Page 10

    1.3 product documentation 1.3.1 product documentation set guid-3aa69ea6-f1d8-47c6-a8e6-562f29c67172 v15 iec07000220-4-en.Vsd p la n n in g & p u rc h a se e n gi n e e rin g in st a lli n g c o m m is si o n in g o p e ra tio n m ai n te n a n ce d e co m m is si o n in g d e in st a lli n g & d is ...

  • Page 11

    The commissioning manual contains instructions on how to commission the ied. The manual can also be used by system engineers and maintenance personnel for assistance during the testing phase. The manual provides procedures for the checking of external circuitry and energizing the ied, parameter sett...

  • Page 12

    1.3.3 related documents guid-94e8a5ca-be1b-45af-81e7-5a41d34ee112 v5 documents related to reb650 document numbers application manual 1mrk 505 388-uen commissioning manual 1mrk 505 390-uen product guide 1mrk 505 391-ben technical manual 1mrk 505 389-uen type test certificate 1mrk 505 391-ten document...

  • Page 13

    Documents related to ret650 document numbers application manual 1mrk 504 169-uen commissioning manual 1mrk 504 171-uen product guide 1mrk 504 172-ben technical manual 1mrk 504 170-uen type test certificate 1mrk 504 172-ten 650 series manuals document numbers operation manual 1mrk 500 128-uen enginee...

  • Page 14

    The caution icon indicates important information or warning related to the concept discussed in the text. It might indicate the presence of a hazard which could result in corruption of software or damage to equipment or property. The information icon alerts the reader of important facts and conditio...

  • Page 15

    • signals in frames with a shaded area on their right hand side represent setting parameter signals that are only settable via the pst, ect or lhmi. • if an internal signal path cannot be drawn with a continuous line, the suffix - int is added to the signal name to indicate where the signal starts a...

  • Page 16

    10

  • Page 17

    Section 2 dnp3 data mappings 2.1 overview guid-ec7d1f5e-ffe0-4837-b02a-45e1cd531a94 v3 this document describes the available dnp3 data points and structures in the ieds. The data points are unmapped as a default. The point list tables represents the superset of available dnp3 data points in these ie...

  • Page 18

    Function name signal type signal name description bi4 binary input 4 bi5 binary input 5 bi6 binary input 6 bi7 binary input 7 bi8 binary input 8 bi9 binary input 9 bi10 binary input 10 bi11 binary input 11 bi12 binary input 12 bi13 binary input 13 bi14 binary input 14 bi15 binary input 15 bi16 binar...

  • Page 19

    Function name signal type signal name description bi7 binary input 7 bi8 binary input 8 blkout block binary outputs bo1 binary output 1 bo2 binary output 2 bo3 binary output 3 bo4 binary output 4 bo5 binary output 5 bo6 binary output 6 bo7 binary output 7 bo8 binary output 8 bo9 binary output 9 bo10...

  • Page 20

    Function name signal type signal name description cmdbit31 command out bit 31 cmdbit32 command out bit 32 general functions for showing signals for dnp master mvgapc analog inputs in magnitude of deadband value sp16gapc binary inputs in1 input 1 status in2 input 2 status in3 input 3 status in4 input...

  • Page 21

    Function name signal type signal name description trret retrip by breaker failure protection function trret_a retrip by breaker failure protection function phase a trret_b retrip by breaker failure protection function phase b trret_c retrip by breaker failure protection function phase c ccsspvc bina...

  • Page 22

    Function name signal type signal name description ch2fltang fault angle ch2fltmag fault magnitude ch2mag prefault magnitude ch3ang prefault angle ch3fltang fault angle ch3fltmag fault magnitude ch3mag prefault magnitude ch4ang prefault angle ch4fltang fault angle ch4fltmag fault magnitude ch4mag pre...

  • Page 23

    Function name signal type signal name description ch14fltmag fault magnitude ch14mag prefault magnitude ch15ang prefault angle ch15fltang fault angle ch15fltmag fault magnitude ch15mag prefault magnitude ch16ang prefault angle ch16fltang fault angle ch16fltmag fault magnitude ch16mag prefault magnit...

  • Page 24

    Function name signal type signal name description ch26mag prefault magnitude ch27ang prefault angle ch27fltang fault angle ch27fltmag fault magnitude ch27mag prefault magnitude ch28ang prefault angle ch28fltang fault angle ch28fltmag fault magnitude ch28mag prefault magnitude ch29ang prefault angle ...

  • Page 25

    Function name signal type signal name description ef4ptoc binary inputs pufw pick up foward direction purev pick up reverse direction trst1 trip signal from step 1 trst2 trip signal from step 2 trst3 trip signal from step 3 trst4 trip signal from step 4 trip general trip signal trsotf trip signal fr...

  • Page 26

    Function name signal type signal name description lovptuv binary inputs trip trip signal lt3cpdif binary inputs blk2h block signal due to second harmonic blk5h block signal due to fifth harmonic intfault internal fault has been detected openctal open ct alarm output signal. Issued after a delay ... ...

  • Page 27

    Function name signal type signal name description trst2_b trip signal from step2 phase b trst2_c trip signal from step2 phase c trip trip pcfcnt analog inputs scal_val scaled value with time and status information counters cnt_val actual pulse counter value phpioc binary inputs trip trip signal from...

  • Page 28

    Function name signal type signal name description autorel automatic release manrel manual release slgapc analog inputs swposn switch position (integer) binary outputs close_cmd close command parameter for dnp protocol open_cmd open command parameter for dnp protocol smbi binary inputs bi1 binary inp...

  • Page 29

    Function name signal type signal name description countar counting total number of reclosing shots smpptrc binary inputs cllkout circuit breaker lockout output (set until reset) tr1p tripping single-pole tr2p tripping two-pole tr3p tripping three-pole trip general trip output signal tr_a trip signal...

  • Page 30

    Function name signal type signal name description trnssens trip signal from sensitive negative sequence differential protection trnsunr trip signal from unrestrained negative sequence differential protection teigapc binary inputs alarm indicator of the integrated time has reached the alarm limit war...

  • Page 31

    Function name signal type signal name description vnmmxu analog inputs va va amplitude, magnitude of reported value va_angl va angle, magnitude of reported value vb vb amplitude, magnitude of reported value vb_angl vb angle, magnitude of reported value vc vc amplitude, magnitude of reported value vc...

  • Page 32

    26.

  • Page 33

    Section 3 dnp3 protocol implementation 3.1 dnp3 device profile guid-842fb3dd-b5e2-4e8a-b617-c9d6a8bdd6d1 v3 the following table provides a device profile document in the standard format defined in the dnp3 subset definitions document. While it is referred to in the dnp3 subset definitions as a docum...

  • Page 34

    1.1 device identification capabilities current value if configurable, list methods 1.1.8 supported function blocks pst or lhmi ● self address reservation ○ data sets ○ file transfer ○ virtual terminal ○ mapping to iec 61850 object models defined in a dnp3 xml file ○ function code 31, activate config...

  • Page 35

    1.1 device identification capabilities current value if configurable, list methods 1.1.12 dnp3 xml files available off-line rd wr filename description of contents not supported ○ ● dnpdp.Xml complete device profile ○ ○ dnpdpcap.Xml device profile capabilities ○ ○ dnpdpcfg.Xml device profile config v...

  • Page 36

    1.2a serial connections capabilities current value if configurable, list methods ● none none pst of lhmi (trxtotxmindel) ○rs-485 options: ● requires rx inactive before tx ○ other, explain: 1.2.5 interval to request link status. Indicates how often to send data link layer status requests on a serial ...

  • Page 37

    1.2a serial connections capabilities current value if configurable, list methods ● not checked not checked ○ no gap permitted ○ fixed at _____ bit times ○ fixed at _____ ms ○ configurable, range ____ to ____ bit times ○ configurable, range ____ to ____ ms ○ configurable, selectable from ___,___,___b...

  • Page 38

    1.2b serial connections capabilities current value if configurable, list methods ● none none pst or lhmi (trxtotxmin del) rs–485 options: ● requires rx inactive before tx ○ other, explain: 1.2.5 interval to request link status: indicates how often to send data link layer status requests on a serial ...

  • Page 39

    1.2b serial connections capabilities current value if configurable, list methods ● not checked not checked ○ no gap permitted ○ fixed at bit times ○ fixed at ms ○ configurable, range ___ to ___ bit times ○ configurable, range ____ to ____ ms ○ configurable, selectable from ___,___,___bit times ○ con...

  • Page 40

    1.3 ip networking capabilities current value if configurable, list methods ● allows all (show as *.*.*.* in 1.3.7) specified ip- address ● limits based on ip address ○ limits based on list of ip addresses ● limits based on a wildcard ip address ○ limits based on list of wildcard ip addresses ○ other...

  • Page 41

    1.3 ip networking capabilities current value if configurable, list methods ○ fixed at 20,000 ○ configurable, range _______ to _______ ○ configurable, selectable from ____,____,____ ○ configurable, other, describe: 1.3.13 destination udp port for initial unsolicited null responses (udp only outstatio...

  • Page 42

    Table 6: link layer 1.4 link layer capabilities current value if configurable, list methods 1.4.1 data link address: indicates if the link address is configurable over the entire valid range of 0 to 65,519. Data link addresses 0xfff0 through 0xffff are reserved for broadcast or other special purpose...

  • Page 43

    1.4 link layer capabilities current value if configurable, list methods ○ none 3 pst or lhmi (dlinkretries) ○ fixed at ● configurable, range 0 to 255 ○ configurable, selectable from ____,____,____ ○ configurable, other, describe: 1.4.8 maximum number of octets transmitted in a data link frame: this ...

  • Page 44

    1.5 application layer capabilities current value if configurable, list methods ○ fixed at 2048 pst or lhmi (aplaymaxrxsize) ● configurable, range 20 to 2048 ○ configurable, selectable from ____,____,____ ○ configurable, other, describe: 1.5.4 time-out waiting for complete application layer fragment:...

  • Page 45

    1.5 application layer capabilities current value if configurable, list methods 1.5.9 control status codes supported: indicates which control status codes are supported by the device: • masters must indicate which control status codes they accept in outstation responses • outstations must indicate wh...

  • Page 46

    1.7 fill out the following items for outstations only capabilities current value if configurable, list methods 1.7.2 how often is time synchronization required from the master: details of when the master needs to perform a time synchronization to ensure that the outstation clock does not drift outsi...

  • Page 47

    1.7 fill out the following items for outstations only capabilities current value if configurable, list methods ● per object group (see part 3) per object group ○ per object group (see part 3) class 1: fixed at______ configurable, range _______ to _______ configurable, selectable from ___,___,___ con...

  • Page 48

    ○ always sometimes ● sometimes, explain: only when it contains events ○ never 1.7.9 dnp command settings preserved through a device reset: if any of these settings are written through the dnp protocol and they are not preserved through a restart of the outstation, the master will have to write them ...

  • Page 49

    1.8 outstation unsolicited response support capabilities current value if configurable, list methods ○ fixed at 1 pst or lhmi (masteraddres) ● configurable, range 0 to 65519 ○ configurable, selectable from ____,____,____ ○ configurable, other, describe: 1.8.3 unsolicited response confirmation time-o...

  • Page 50

    1.9 outstation unsolicited response trigger conditions capabilities current value if configurable, list methods ○ class 2 not used to trigger unsolicited responses 5 pst or lhmi (urevcntthold2) ○ fixed at ● configurable, range 1 to 100 ○ configurable, selectable from ____,____,____ ○ configurable, o...

  • Page 51

    1.9 outstation unsolicited response trigger conditions capabilities current value if configurable, list methods ○ class 3 not used to trigger unsolicited responses 5 seconds pst or lhmi (turevbuftout3) ○ fixed at ___________ ms ● configurable, range 0 to 60 ○ configurable, selectable from ____,____,...

  • Page 52

    1.10 outstation performance capabilities current value if configurable, list methods ● never at startup and 1800 seconds after last sync pst or lhmi (tsynchtimeout) ● asserted at startup until first time synchronization request received ○ periodically every____ seconds ○ periodically, range ____to__...

  • Page 53

    1.10 outstation performance capabilities current value if configurable, list methods 1.10.7 maximum event time-tag error for local binary and double bit i/o (ms): the error between the time-tag reported and the absolute time of the physical event. This error includes the internal time reference erro...

  • Page 54

    1.13 broadcast functionality capabilities current value if configurable, list methods 1.13.1 support for broadcast functionality: ○ disabled ● enabled ○ configurable 1.13.2 write functions (fc = 2) supported with broadcast requests: write clock (g50v1 with qualifier code 07): ○ disabled ● enabled ○ ...

  • Page 55

    1.13 broadcast functionality capabilities current value if configurable, list methods 1.13.7 freeze and clear functions (fc = 9) supported with broadcast requests: ● disabled ○ enabled ○ configurable (described elsewhere 1.13.8 freeze and clear, no acknowledgment functions (fc = 10) supported with b...

  • Page 56

    1.13 broadcast functionality capabilities current value if configurable, list methods 1.13.18 enable unsolicited functions (fc = 20) supported with broadcast requests: enable unsolicited by event class (g60v2, g60v3 and g60v4 with qualifier code 06): ○ disabled ● enabled ○ configurable (described el...

  • Page 57

    3.1 binary inputs static (steady-state) group number: 1 event group number: 2 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods 3.1.1 static variation reported when variation 0 requested or in response to class polls: ● variation 1 –...

  • Page 58

    3.6 double-bit binary inputs static (steady-state) group number: 3 event group number: 4 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods 3.6.1 static variation reported when variation 0 requested or in response to class polls: note...

  • Page 59

    3.6 double-bit binary inputs static (steady-state) group number: 3 event group number: 4 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ● fixed at 1000 ○ configurable, range _______ to _______ ○ configurable, selectable from ____,...

  • Page 60

    3.7 binary outputs and binary output commands binary outputs group number: 10 binary output events group number: 11 binary output commands group number: 12 binary output command events group number: 13 capabilities (leave tick-boxes blank if this data type is not supported) current value if configur...

  • Page 61

    3.7 binary outputs and binary output commands binary outputs group number: 10 binary output events group number: 11 binary output commands group number: 12 binary output command events group number: 13 capabilities (leave tick-boxes blank if this data type is not supported) current value if configur...

  • Page 62

    3.7 binary outputs and binary output commands binary outputs group number: 10 binary output events group number: 11 binary output commands group number: 12 binary output command events group number: 13 capabilities (leave tick-boxes blank if this data type is not supported) current value if configur...

  • Page 63

    3.8 counters/ frozen counters counter group number: 20 frozen counter group number: 21 counter event group number: 22 frozen counter event group number: 23 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods 3.8.1 static counter variat...

  • Page 64

    3.8 counters/ frozen counters counter group number: 20 frozen counter group number: 21 counter event group number: 22 frozen counter event group number: 23 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ● a: only most recent (valu...

  • Page 65

    3.8 counters/ frozen counters counter group number: 20 frozen counter group number: 21 counter event group number: 22 frozen counter event group number: 23 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods 3.8.7 frozen counters inclu...

  • Page 66

    3.8 counters/ frozen counters counter group number: 20 frozen counter group number: 21 counter event group number: 22 frozen counter event group number: 23 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ○ master request not suppor...

  • Page 67

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods 3.9...

  • Page 68

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ● v...

  • Page 69

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ● a...

  • Page 70

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ○ v...

  • Page 71

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ○ v...

  • Page 72

    3.9 analog inputs static (steady-state) group number: 30 static frozen group number: 31 event group number: 32 frozen analog input event group number: 33 deadband group number: 34 capabilities (leave tick-boxes blank if this data type is not supported) current value if configurable, list methods ○ a...

  • Page 73

    3.10 analog outputs and analog output commands analog output status group number: 40 analog outputs group number: 41 analogue output events group number: 42 analogue output command events group number: 43 capabilities (leave tick-boxes blank if this data type is not supported) current value if confi...

  • Page 74

    3.10 analog outputs and analog output commands analog output status group number: 40 analog outputs group number: 41 analogue output events group number: 42 analogue output command events group number: 43 capabilities (leave tick-boxes blank if this data type is not supported) current value if confi...

  • Page 75

    3.10 analog outputs and analog output commands analog output status group number: 40 analog outputs group number: 41 analogue output events group number: 42 analogue output command events group number: 43 capabilities (leave tick-boxes blank if this data type is not supported) current value if confi...

  • Page 76

    3.10 analog outputs and analog output commands analog output status group number: 40 analog outputs group number: 41 analogue output events group number: 42 analogue output command events group number: 43 capabilities (leave tick-boxes blank if this data type is not supported) current value if confi...

  • Page 77

    3.10 analog outputs and analog output commands analog output status group number: 40 analog outputs group number: 41 analogue output events group number: 42 analogue output command events group number: 43 capabilities (leave tick-boxes blank if this data type is not supported) current value if confi...

  • Page 78

    Table 14: implementation table dnp object group and variation request (slave will parse) response (slave will respond with) object group number variation number description function codes (dec) qualifier codes (hex) function codes (dec) qualifier codes (hex) 1 0 binary input – any variation 1 (read)...

  • Page 79

    Dnp object group and variation request (slave will parse) response (slave will respond with) 4 1 double bit input change event without time 130 (unsol. Resp) 17, 28 (index) 4 2 double bit input change event with absolute time 1 (read) 06 (no range, or all) 07, 08 (limited qty) 129 (response) 17, 28 ...

  • Page 80

    Dnp object group and variation request (slave will parse) response (slave will respond with) 20 2 16–bit binary counter (with flag) 1 (read) 00, 01 (start-stop) 06 (no range, or all) 07, 08 (limited qty) 17, 27, 28 (index) 129 (response) 00,01 (start-stop) 17, 28 (index) 2) 20 5 1) 32–bit binary cou...

  • Page 81

    Dnp object group and variation request (slave will parse) response (slave will respond with) 30 5 analog input — single precision, floating point with flag 1 (read) 00, 01 (start-stop) 06 (no range, or all) 07, 08 (limited qty) 17, 27, 28 (index) 129 (response) 00,01 (start-stop) 17, 28 (index) 2) 3...

  • Page 82

    Dnp object group and variation request (slave will parse) response (slave will respond with) 32 7 analog input change event — single precision, floating point with time 1 (read) 06 (no range, or all) 07, 08 (limited qty) 129 (response) 17, 28 (index) 32 7 analog input change event — single precision...

  • Page 83

    Dnp object group and variation request (slave will parse) response (slave will respond with) 60 3 class objects — class 2 data 1 (read) 06 (no range, or all) 07, 08 (limited qty) 60 3 class objects — class 2 data 20 (enbl. Unsol.) 06 (no range, or all) 60 3 class objects — class 2 data 21 (disable u...

  • Page 84

    78.

  • Page 85

    Section 4 glossary 4.1 glossary m14893-1 v16 ac alternating current acc actual channel act application configuration tool within pcm600 a/d converter analog-to-digital converter adbs amplitude deadband supervision adm analog digital conversion module, with time synchronization ai analog input ansi a...

  • Page 86

    C37.94 ieee/ansi protocol used when sending binary signals between ieds can controller area network. Iso standard (iso 11898) for serial communication cb circuit breaker cbm combined backplane module ccitt consultative committee for international telegraph and telephony. A united nations-sponsored s...

  • Page 87

    Darpa defense advanced research projects agency (the us developer of the tcp/ip protocol etc.) dbdl dead bus dead line dbll dead bus live line dc direct current dfc data flow control dft discrete fourier transform dhcp dynamic host configuration protocol dip-switch small switch mounted on a printed ...

  • Page 88

    Fox 6plus compact time-division multiplexer for the transmission of up to seven duplex channels of digital data over optical fibers fpn flexible product naming ftp file transfer protocol fun function type g.703 electrical and functional description for digital lines used by local telephone companies...

  • Page 89

    Ieee institute of electrical and electronics engineers ieee 802.12 a network technology standard that provides 100 mbits/s on twisted-pair or optical fiber cable ieee p1386.1 pci mezzanine card (pmc) standard for local bus modules. References the cmc (ieee p1386, also known as common mezzanine card)...

  • Page 90

    Irig-b: interrange instrumentation group time code format b, standard 200 itu international telecommunications union lan local area network lib 520 high-voltage software module lcd liquid crystal display ldcm line data communication module ldd local detection device led light-emitting diode lnt lon ...

  • Page 91

    Pcm600 protection and control ied manager pc-mip mezzanine card standard pmc pci mezzanine card por permissive overreach pott permissive overreach transfer trip process bus bus or lan used at the process level, that is, in near proximity to the measured and/or controlled components prp parallel redu...

  • Page 92

    Slm serial communication module. Sma connector subminiature version a, a threaded connector with constant impedance. Smt signal matrix tool within pcm600 sms station monitoring system sntp simple network time protocol – is used to synchronize computer clocks on local area networks. This reduces the ...

  • Page 93

    Tpz, tpy, tpx, tps current transformer class according to iec trm transformer module. This module transforms currents and voltages taken from the process into levels suitable for further signal processing. Typ type identification umt user management tool underreach a term used to describe how the re...

  • Page 94

    88.

  • Page 95

    89.

  • Page 96

    — abb ab grid automation products 721 59 västerås, sweden phone: +46 (0) 21 32 50 00 abb.Com/protection-control © copyright 2017 abb. All rights reserved. Specifications subject to change without notice. 1mrk 511 41 9-uus.