1. DL manuals
  2. AccuPower
  3. Battery Charger
  4. AccuManager 807
  5. Operating Manual

AccuPower AccuManager 807 Operating Manual

Manual is about: Balance CHARGER/DISCHARGER FOR NICD/NIMH/LITHIUM/PB BATTERIES

Summary of AccuManager 807

  • Page 1

    Accupower accumanager 807 balance charger/discharger operating manual for nicd/nimh/lithium/pb batteries thank you for purchasing the accumanager 807. This is a rapid charge/discharger with built in balancer, computerised with micr- oprocessor and specialised operating software. Please read this ent...

  • Page 2: Features

    Features optimised operating software when charging or discharging, a p 8 0 7 has an ‘auto’ function that sets the feeding current automatically. Especially for lithium batteries, it can prevent the over-charging can lead to an explosion by users fault. Every program in the unit is controlled with m...

  • Page 3

    Auto-charge current limit: when charging nicd or nimh at ‘auto’current mode, you can set the upper limit of change current to avoid from high current charging. This is very useful when charging the low impedance and small capacity nimh battery in “auto’mode. Capacity limit: the changing capacity alw...

  • Page 4: Exterior Of The Unit

    Exterior of the unit lithium balance charge program connection diagram warning it will damage the charger if you connect your battery with the ap807 incorrectly. The b- connector is on the mostly right pin at all 6 balancing plugs. B-.

  • Page 5: Warnings and Safety Notes

    Warnings and safety notes supply. If any malfunction is observed immediately terminate the process and refer to the operation manual. Vibration. Do not drop it. . Head-resistant, non-inflammable and non-conductive surface. Never place them on a car seat, carpet or similar. Keep all the inflammable v...

  • Page 6

    Do not connect more than one battery pack to the charge lead at any one time. Do not attempt to charge or discharge the following types of battery. Battery pack, which consists of different types of cell (including different manufacturers). -battery, which is already fully charged or just slightly d...

  • Page 7

    -do not attempt to disassemble the battery pack arbitrarily. -you have to pay attention to verify the capacity and the voltage of the lithium battery pack. It may be composed of parallel and series connection mixed. In parallel link the capacity of the battery pack is multiplied by the number of cel...

  • Page 8: Program Flow Chart

    Program flow chart program select lixx batt lixx charge lixx charge lixx balance lixx fast chg lixx storage lixx discharge program select nimh batt nimh charge aut nimh charge man nimh discharge nimh cycle program select nicd batt nicd charge aut nicd charge man nicd discharge nicd cycle program sel...

  • Page 9

    Initial parameter set up (users set up) ap807 will be operated with the default value of the essential user settings when it is connected to a 12v batttery for the first time.The screen displays the following information in sequence and the user can change the value of parameter on each screen. When...

  • Page 10

    This shows the trigger voltage for automatic charge termination of nimh and nicd battery. The effective value ranges from 5 to 20mv per cell .If the trigger voltage is set higher, there is a danger of overcharging the battery; if it is set lower, there is a possibility of premature termination. Plea...

  • Page 11

    This program sets the maximum charge capacity that will be supplied to the battery during charge. If the delta-pack voltage is not detected nor the safety timer expired by any reason, this feature will automatically stop the process at the selected capacity value. The beep sounds at every time press...

  • Page 12: Charging Lithium Battery

    The left side of the first line shows the type of battery you select at the users setting. The value on the left side of second line sets a charge current and the value on the right side of second line sets the voltage of the battery pack. After setting the current and voltage press start/enter key ...

  • Page 13

    After setting the current and voltage press start/enter key for more than 3 seconds to start the process. (charge current:0.1~7.0a, volatge:1~8series) this shows the number of cells you set up and the processor detects. ‘r:’ shows the number of cells found by the charger and ‘s:’ is the number of ce...

  • Page 14

    ‘storage ’ control lithium battery discharging lithium battery this is for charging or discharging lithium battery not to be used for the time being. The program will determine to charge or discharge the battery to the certain voltage depending on the voltage of the battery at its initial stage. The...

  • Page 15: Nimh/nicd Battery Program

    Voltage balancing and monitoring during the discharge the processor monitors the voltage of individual cells during ‘storage-mode’ and ‘discharge’ of lithium battery pack. It tries to normalise the voltages to be equal. For this feature, the individual plug of the battery pack should be connected to...

  • Page 16

    Impedance and small capacity can lead to the higher charge current by the processor at automatic charge mode. But in‘man’ mode, it will charge the battery with the charge current you set at the display. Each mode can be switched by pressing inc and dec button simultaneously when the current field is...

  • Page 17: Charging Pb Battery

    To stop the process, press batt type/stop key once. You can change the discharge or charge current by pressing start/enter key once during the process. The audible sound indicates you the end of process. At the end of the process, you can see charged or discharged electric capaci- ties of the batter...

  • Page 18: Discharging Pb Battery

    Discharging pb battery the screen displays the state of charging process. To stop charging forcibly, press batt type/stop key once. The audible sound indicates you at the end of process. Set discharge current on the left and final voltage on the right. The discharge current ranges from 0.1 to 5.0a. ...

  • Page 19: Load Data Program

    With the battery type you set up. The example shows the battery pack of nimh, 12cells and 3000mah of capacity. Set up the charge current for manual charge mode, or the current limit for automatic charge mode. Each mode can be switched by pressing inc and dec button at the same time when the current ...

  • Page 20

    Various information during the process you can inquire various information on lcd screen during charging or discharging process. When you press dec button the charger shows the establishment of user settings. And also you can monitor the voltage of individual cell by pressing inc button when the ind...

  • Page 21: Warning and Error Messages

    Ap807 incorporates a various functions of protective and monitoring the system to verify functions and the state of its electronics. In any case of occurring error, the screen displays the cause of error that is self- explanatory with audible sound. The output is connected to a battery with incorrec...

  • Page 22: Specifications

    Specifications operating voltage range: 10.0~18.0volt circuit power: max.150w charge current range: 0.1~7.0a discharge current range: 0.1~5.0a current drain for balancing li-po: 300mah/cell nicd/ nimh battery cell count: 1~27cells lithium battery cell count: 1~8series pb battery voltage: 2 to 36v we...

  • Page 23

    ＲｏＨｓ accu power www.Accupower.At www.Accupower.De.