1. DL manuals
  2. Accurate Technology
  3. Receiver
  4. ProScale
  5. User Manual

Accurate Technology ProScale User Manual

Manual is about: LCD Readouts With Firmware Version 3.1 and higher

Summary of ProScale

  • Page 1

    Firmware version 1.0 and greater user manual proscale rf receiver.

  • Page 2: Attention

    Proscale rf receiver user manual page 2 of 20 this document is protected by the copyright laws of the united states of america. No part of this document may be reproduced by any means, electronic or otherwise, without the expressed written permission of accurate technology, inc. Firmware version 1.0...

  • Page 3: Fcc Notice

    Accurate technology inc. Page 3 of 20 fcc notice this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installatio...

  • Page 4: Table Of Contents

    Proscale rf receiver user manual page 4 of 20 table of contents section 1 general information ............................................... 5 i ntroduction .................................................................................................. 5 w hat t his m anual c ontains ..............

  • Page 5: Ection

    Accurate technology inc. Page 5 of 20 s ection 1 g eneral i nformation introduction thank you for purchasing the proscale receiver system. This radio receiver unit is designed to be used in conjunction with accurate technology, inc. Proscale™ linear measuring systems that are equipped with integral ...

  • Page 6: What This Manual Contains

    Proscale rf receiver user manual page 6 of 20 what this manual contains this manual covers only the proscale-rf digital display receiver it is intended to supplement the proscale manual part number 800-1097-001, covering the operation of the wireless digital display. Terminology this section provide...

  • Page 7: Ection

    Accurate technology inc. Page 7 of 20 s ection 2 i nstallation the proscale rf receiver is simple to install and connect to a pc. 1. Connect the low voltage dc power supply (provided) to the rear of the receiver. Plug the power supply into an ac outlet. The top green led on the front of the receiver...

  • Page 8: Ection

    Proscale rf receiver user manual page 8 of 20 s ection 3 c onfiguration depending on the receiver model you have purchased, the unit has the ability to receive signals from either a single proscale rf display or from multiple proscale rf displays. After the receiver is connected to the computer and ...

  • Page 9: Command Format

    Accurate technology inc. Page 9 of 20 command format the receiver uses a standard format for all configuration commands. 1. A single command letter. Lower case letters allow the current parameter state to be viewed without modification. Upper case letters allow the user to change the parameter confi...

  • Page 10: Output Modes

    Proscale rf receiver user manual page 10 of 20 output modes there are six output modes available on the proscale rf receiver. The first five are ascii text formats and the sixth mode is a binary data mode that provides partial message emulation for accurate technology’s prorf™ two- way radio system....

  • Page 11: Output Mode 3

    Accurate technology inc. Page 11 of 20 output mode 3 positionunitsid example: inches with delimiter, unit id 3: 5.637 in 3 millimeters with delimiter, unit id 2: 28.35 mm 2 output mode 4 full message display the full message display mode provides two types of messages depending on the type of signal...

  • Page 12: Output Mode 5

    Proscale rf receiver user manual page 12 of 20 output mode 5 binary mode output, prorf emulation this output mode is intended to be used with applications that were designed for the prorf two-way radio interface system. The output from this receiver is a small subset of the functionality from the pr...

  • Page 13

    Accurate technology inc. Page 13 of 20 example: position packet message, position 8.537 inches from display unit id 1, signal strength 5, message 34. Byte number value description 1 255 destination address (receiver) 2 1 display address id 3 ‘a’ position command character ascii a 4 ‘5’ signal streng...

  • Page 14: Ection

    Proscale rf receiver user manual page 14 of 20 s ection 4 o peration command format examples the following examples demonstrate how to configure various parameters of the proscale rf receiver system. Is the enter key on the pc. If an invalid command letter is entered, the receiver will provide the f...

  • Page 15: Echo Mode

    Accurate technology inc. Page 15 of 20 to change the delimiter to a tab character, type: d where = the pc tab key. The receiver responds with: delimiter now = echo mode to display the current echo mode (from default), type in: e the receiver responds with: echo mode (factory default = on) to change ...

  • Page 16: Baud Rate

    Proscale rf receiver user manual page 16 of 20 baud rate to display the current baud rate (from default), type in: b the receiver responds with: baud rate = ¸ (factory default = 9600) to change the baud rate to 19200, type: b19200 the receiver responds with: baud rate will be = 19200 the baud rate c...

  • Page 17

    Accurate technology inc. Page 17 of 20 defaulting the receiver to factory values in the event that the user wishes to restore the receiver to factory values, complete the following: 1. Remove the four screws from the bottom of the receiver and remove the top cover. 2. Locate and press the small push...

  • Page 18

    Proscale rf receiver user manual page 18 of 20 this page intentionally left blank.

  • Page 19: Roduct

    Accurate technology inc. Page 19 of 20 p roduct r egistration fill out for your records and fax to accurate technology @ +1.828.654.8824 or register on line at http://www.Proscale.Com/registration.Htm name e-mail company address address city state/region zip/postal code country purchased from: purch...

  • Page 20: Technology Product

    Proscale rf receiver user manual page 20 of 20 thank you for choosing an accurate technology product made in usa accurate technology, inc. 270 rutledge rd. Unit e fletcher, nc 28732 usa 800 233-0580 • 828-654-7920 fax 828-654-8824 www.Proscale.Com customerservice@accurate-technology.Com this manual ...