AIRLESSCO 1200G Service & Operation Manual - Selection Chart
12
13
REV-TIP
™
SELECTION CHART
PATTERN WIDTH
Thickness of the paint coat per stroke is determined by spray tip
"fan width", rate of the spray gun movement, and the distance to
the surface being sprayed.
SPRAY TIP SELECTION
Two tips having the same tip size, but different pattern widths
will deliver the same amount of paint over a different area (wider
or narrower strip). A spray tip with a narrow pattern width makes it
easy to spray in tight places.
SPRAY TIP REPLACEMENT
During use, especially with latex paint, high pressure will
cause the orifice to grow larger. This destroys the pattern.
Replace tips before they become excessively worn.
Worn tips waste paint, cause overspray, make cutting-in
difficult, and decreases sprayer performance.
Spray tip size is based on how many gallons of paint per minute can
be sprayed through the tip. Do not use a tip larger than the max-
imum pump flow rate or capacity the sprayer can accommodate.
Pump flow rate is measured in gallons per minute (GPM).
Spray tip selection is based on paint viscosity, paint type, and
job needs. For light viscosities (thin paints), use a smaller tip;
for heavier viscosities (thicker paints), use a larger tip size.
For sizes not shown, call factory for availability.
SPRAY PAINTING TIP - ORIFICE SIZE
(Inches)
(water @ 2000psi, 138 bar)
(latex paint @ 2000psi,
138 bar/1.36 spec. gr.)
*Pump will support tip worn to next larger size.
TIP IDENTIFICATION:
1st 3-digits identifies it as a REV-TIP
TM
for airless paint spraying (P.N. 560-xxx) or
a REV-TIP
TM
for airless line striping (P.N. 562-xxxST).
4th digit is the fan width - the number is half the fan width, e.g., 5 means a 10” fan.
5th and 6th digits are for the orifice size and is measured in thousandths of an inch,
e.g., 17 = 0.017 inch - The higher the number, the larger the tip.
Water Flow Rate (gpm)
.12 .18 .24 .31 .38 .47 .57 .67 .77 1.03 1.31
(lpm)
.49 .69 .91 1.17 1.47 1.79 2.15 2.54 2.96 3.90 4.98
Paint Flow Rate (gpm)
.10 .15 .21 .27 .33 .40 .49 .58 .66 .88 1.12
(lpm)
.38 .57 .79 1.02 1.25 1.51 1.85 2.20 2.50 3.33 4.24
Pump Minimum
(gpm)
.25 .25 .33 .40 .50 .60 .75 .88 1.0 1.25 1.5
Output*
(lpm)
1.0 1.0 1.25 1.5 1.9 2.3 2.8 3.3 3.8 4.7 5.7
Rev-Tip
TM
for Painting
Fan Width (12” from surface)
in. (mm) .009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .031 .035
4-6 102-152 209 211 213 215 217 219 221 223 225 227 229
6-8 152-203 309 311 313 315 317 319 321 323 325 327 335
8-10 203-254 409 411 413 415 417 419 421 423 425 427 431
10-12 254-305 511 513 515 517 519 521 523 525 527 531 535
12-14 305-356 613 615 617 619 621 623 625 627 631 635
14-16 356-406 715 717 721
16-18 406-457 815 819 821 831
Gun Filter
C= Coarse - 60 mesh
F F F,C C C C C REMOVE FILTER
F= Fine - 100 mesh
Wood
Lacquer, Varnish
•
Interior
Stain, Sealer
•
•
Enamel
•
Wood
Exterior Stain
• •
Exterior
Vinyl, Acrylic, Latex
•
•
Masonry
Vinyl, Oil Base Alkyd
• •
Latex, Acrylic
•
• • •
Block Filler
• • • • •
Elastomer
•
•
•
• • •
Ceiling
Hi Build, Mil White
•
•
Structural Steel
Heavy Coatings
•
•
• • • •
STRIPING TIP - ORIFICE SIZE
(Inches)
in (mm)
.009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .031 .035
1-2 25-51
113ST 115ST 117ST 119ST
2-4 51-102
215ST 217ST 219ST 221ST
4-6
102-152
315ST 317ST 319ST 321ST
6-8 152-203
Striping Paint
Oil Base Oil Base Latex
Latex
Latex
Latex
Latex
Latex
Rev-Tip
TM
for Striping
Fan Width (6” from surface)
.
029
Rev-Tip
TM
for
Painting
P.N. 56
0
-xxx
Rev-Tip
TM
for
Striping
P.N. 56
2
-xxxST