G uide to i nstallation of the b & k ck1.2 k eypad s b i m p ly e t t e r ! B k & rev b 0104 main in 6 in 1 in 7 in 2 in 8 in 3 in 8 in 4 fm in 5 page 1.
Thank you for choosing to install the b & k ck 1.2 keypad for this system! Please use this manual as a guide to connecting and mounting the keypad. The ck1.2 keypad is preprogrammed at the factory to initially operate b & k ct products. It can be re-programmed using a windows pc and the accompanying...
S b i m p ly e t t e r ! B k & table of contents features and benefits 1 basic controls and displays 2 rear panel connections 3 programming jack - behind the faceplate 4 terminate rj-45’s one to one 4 standard ct610/310/600 system configuration 5 connecting to a ct610/310/600 6 keypad total power co...
Page 1 features and benefits vast programming capacity the ck1.2 can be programmed with 44 ir commands for each of up to 20 components or devices. Additionally, you can label the commands with user friendly names that your client will find easy to use. One touch automates operation the on, off and a...
Page 2 s b i m p ly e t t e r ! B k & basic controls and displays volume/mute buttons control the level of the sound. Change buttons change to the next channel, chapter, song or b&k sound pre- set; depen-ding on the selected activity. Power led lights up when this zone/room is on. Lcd buttons - labe...
Page 3 s b i m p ly e t t e r ! B k & rear panel connections slave (out) connects to the master (in) of any other same-zone keypads via an rj-45 plug. Alternate master (in) the alternate master has two purposes in most systems: 1. You can use it instead of the mas- ter (in) when the cable from the c...
Page 4 s b i m p ly e t t e r ! B k & programming jack - behind the faceplate the face plate is removed by prying up from the two screwdriver tabs at the base of the keypad. Once removed, the programming jack is revealed: terminate rj-45’s one to one you can terminate the rj-45’s using any color cod...
Page 5 s b i m p ly e t t e r ! B k & standard ct610/310/600 system keypads connect to the zone control connectors on the ct610/310/600 via cat 5 cables. Ir flashers for a/v com- ponents are connected to the ir output correspon- ding to their a/v input #. The receiver power amplifiers connect to eac...
Connecting to a ct610/310/600 keypads connect to the ct610/310/600 at the control terminals. There is a set of five terminals for each of the hardware zones labeled a-f on the ct610/600 and a-c on the ct310. You can terminate the keypad cables to the control terminals in one of two ways: 1. If your ...
S b i m p ly e t t e r ! B k & page 7 the b & k pt5 preamp — perfect for adding zones the superb sounding b & k pt5 preamp incorporates a keypad control ter- minal and an ir output for flashers. A simple system would connect like this: keypad total power consumption the ct610/600 control 12vdc outpu...
Page 8 s b i m p ly e t t e r ! B k & keypads with other b & k receivers and preamps the ck1.2 keypad can be easily programmed with the commands for all remote controlled b & k receivers and preamps. Because of b & k’s elegant all discrete code architecture, the ck1.2 will automate and delight owner...
Page 9 s b i m p ly e t t e r ! B k & connecting slave keypads each zone should have only one cat 5 cable home run to the ct610/310/600. When rooms interconnect and open to each other (for example: interconnecting family room, kitchen, dining areas are common in many homes) you may opt to expand a z...
Page 10 s b i m p ly e t t e r ! B k & connecting a local tv or device every keypad can control a local tv or even a local system of components in addition to the components in the main system. A two conductor cable should be run from the keypad location to the local component location. As many as f...
Page 11 s b i m p ly e t t e r ! B k & mounting after connections are made, the ck1.2 installs into a two gang j-box or an open backed double gang trim ring with the enclosed screws. If you opt to use a closed j-box, it must be a minimum of 2 3/4” deep to accomodate standard rj-45 plugs in the rear....
Page 12 s b i m p ly e t t e r ! B k & white and beige wall plate included once programming is complete and downloaded to each keypad, finish the installation off by installing either the white or the beige wall plate. The wall plate simply snaps into place, first from the top, finishing with the bo...
S b i m p ly e t t e r ! B k & b & k components, ltd. 2100 old union road buffalo, new york 14227 1.800.543.5252 in ny: 716.656.0026 fax: 716.656.1291 e-mail: info@bkcomp.Com on the web: www.Bkcomp.Com ck1.2 keypad specifications compatible b&k products avr507/ 505, ref50, pt5, ct610/310/600 operati...
