- DL manuals
- Balluff
- I/O Systems
- BNI EIP-502-105-Z015
- User Manual
Balluff BNI EIP-502-105-Z015 User Manual
Summary of BNI EIP-502-105-Z015
Page 1
Bni eip-502-105-z015 ip67 modules 4 io link/in-/outputs,12 in-/outputs user’s guide.
Page 2
Www.Balluff.Com 1 content 1 notes 3 1.1. About this guide 3 1.2. Structure of the guide 3 1.3. Typographical conventions 3 enumerations 3 actions 3 syntax 3 cross-references 3 1.4. Symbols 3 1.5. Abbreviations 3 2 safety 4 2.1. Intended use 4 2.2. Installation and startup 4 2.3. General safety notes...
Page 3
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 2 7.6. Startup 14 7.7. Main menue 14 7.8. Ip setup 15 7.9. Ip config 15 7.10. Module information 16 7.11. General informations 16 8 webserver 17 8.1. General 17 8.2. Home 17 8.3. Diagnostic process 17 8.4. Device propertie...
Page 4
Www.Balluff.Com 3 1 notes 1.1. About this guide the bni eip- … serves as a decentralized io link, input and output module for connecting to an ethernet/ip™ network. 1.2. Structure of the guide the guide is organized so that the chapters build on one another. Chapter 2: basic safety information. Chap...
Page 5
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 4 2 safety 2.1. Intended use this guide describes the bni eip- … serves as a decentralized io link, input and output module for connecting to an ethernet/ip™ network. 2.2. Installation and startup note installation and sta...
Page 6
Www.Balluff.Com 5 3 getting started 3.1. Modul overview figure 0.1 – overview bni eip-502-100-z016 1 mounting hole 2 ethernet/ip ™ port 2 3 display 4 status led: communication / module 5 port 5 (standard i/o) 6 pin/port led : signal status 7 port 6 (standard i/o) 8 port 7 (io link, standard i/o) 9 p...
Page 7
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 6 3 getting started 3.2. Mechanical connection the module is attached using 2 m6 screws and 2 washers. Isolation pad as accessory available 3.3. Electrical connection power supply in 7/8”, male out 7/8” female pin function...
Page 8
Www.Balluff.Com 7 3 getting started i/o-port m12, a-coded, female pin function 1 +24v, 200ma 2 input / output 3 gnd 4 input / output 5 fe note! For the digital sensor inputs follow the input guideline per en61131-2, type 2. Note! Each output serves a maximum current of 1,6 amperes. Total current of ...
Page 9
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 8 4 technical data 4.1. Dimensions 4.2. Mechanical data housing material die case zinc, matt nickel plated enclosure rating per iec 60529 ip 67 (only when plugged-in and threaded-in) supply voltage 7/8” 4-pin male input po...
Page 10
Www.Balluff.Com 9 4 technical data 4.5. Ethernet ethernet ip port 1 x 10base-/100base-tx connection for ethernet ip port m12, d-coded cable types per ieee 802.3 shielded twisted pair min. Stp cat 5/ stp cat 5e data transmission rate 10/100 mbit/s max. Cable length 100 m flow control half duplex/full...
Page 11
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 10 5 integration 5.1. Data configuration please enter the following values to your control system. They describe the datasizes for input, output and config data. Instance id data length input 100 200 output 101 134 config ...
Page 12
Www.Balluff.Com 11 6 process data 6.1. Process data inputs there are 200 bytes of input data. Have a look at the tables below to see the mapping of the process data inputs. Byte modul part description 0 …7 standard i/o ports process data inputs on standard inputs 8…55 io-link port 1 process data inp...
Page 13
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 12 6 process data 6.2. Process data outputs there are 134 bytes of output data. Have a look at the tables below to see the mapping of the process data outputs. Byte modul part description 0 …5 standard i/o ports process da...
Page 14: ↑
Www.Balluff.Com 13 7 display 7.1. General wi th the implemented display, the address is set directly on the bni eip… devices. The following address types are implemented: • ip address • subnet mask • gateway address. Each address type consists of 4 octets. Additional the display shows information ab...
Page 15: 007
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 14 7 display 7.5. Design and symbols there are some symbols used in the following flow-charts to describe the display- functionality: 7.6. Startup 7.7. Main menue • scrolling in main menue with short-time keypress on set-k...
Page 16: 005
Www.Balluff.Com 15 7 display 7.8. Ip setup • long-time keypress on set key starts editing mode. • configuration of the favored value by short-time keypress on arrow-key 7.9. Ip config • long-time keypress on set key starts editing mode. • configuration of the favored value by short-time keypress on ...
Page 17
Balluff network interface ethernet/ip ™, bni eip-502-105-z015 www.Balluff.Com 16 7 display 7.10. Module information • by short-time keypress on arrow key you can scroll through module information menu. • informations are the product name, the module revisions and the macid. 7.11. General information...
Page 18
Www.Balluff.Com 17 8 webserver 8.1. General the bni eip-502 module includes an internal webserver to get detailed information about the current state. Also you can use it to configurate the module and the connected io link devices. First make sure that a correct integration into your network has bee...
Page 19
Www.Balluff.Com 18 9 appendix 9.1. Included material the bni eip consists of the following components: • io-link block • 4 blind plugs m12 • ground strap • screw m4x6 • 20 labels 9.2. Ordercode bni eip-502-105-z015 balluff network interface ethernet ip functions 502 = ip 67 io link master-modul vari...
Page 20: Www.Balluff.Com
Www.Balluff.Com www.Balluff.Com balluff gmbh schurwaldstrasse 9 73765 neuhausen a.D.F. Germany tel. +49 7158 173-0 fax +49 7158 5010 balluff@balluff.De nr. 8 8 2 4 0 7 e ed iti o n a1 5 rep la c e s e d it io n j 1 1 su b je c t to m o d ifi c a ti o n.