- DL manuals
- Bang & Olufsen
- Stereo System
- BEOSOUND 9000
- Setup Manual
Bang & Olufsen BEOSOUND 9000 Setup Manual
Summary of BEOSOUND 9000
Page 1
B e o s o u n d 9 0 0 0
Page 2
2.
Page 3
3 b e f o r e y o u s t a r t … this setting-up guide explains how to set up your beosound 9000 and make it ready for use. The beosound 9000 may also be used in a fully integrated bang & olufsen av system (see the sections “connections” and “ready for use…”). Please contact your bang & olufsen deale...
Page 4
4 p l a c e m e n t ■ if you are going to hang the beosound 9000 on the wall, always use the correct size and type of screws and wall plugs to support the weight of the beosound 9000 (depending on the material and the construc- tion of the wall). If in doubt, consult your bang & olufsen dealer. ■ li...
Page 5
5 fig. 2: the beosound 9000 hung flat on the wall in a high horizontal position using the bracket type 2054, and two cable covers type 2062. When placed like this the cd mechanism must be centered for a horizontal position. Movement of the glass door into consideration. ■ when lifting the beosound 9...
Page 6
6 > placement fig. 4: the beosound 9000 placed flat on a level surface, e.G. A table or shelf. When placed like this the cd mechanism must be centered for a flat position (factory set- up). Fig. 5: the beosound 9000 placed in a slant position on a level surface, e.G. A table or shelf, using the brac...
Page 7
7 centered for a vertical posi- tion (figs 1 and 3). Centered for a flat or near flat position (figs 4 and 5). This is the factory setup. Centered for a horizontal position (fig. 2). The cd mechanism is spring suspended in order to make the beosound 9000 ‘party-safe’. By centering the cd mechanism, ...
Page 8
8 c o n n e c t i o n s remove the cover in the bottom plate of the beosound 9000 to gain access to the following sockets: • two sockets for the aerial connections (fm and am). • two sockets for active loud- speakers (pl, i.E. Power link). • one socket for auxiliary equipment (aux). • one digital ou...
Page 9
9 beolink connection loud- speakers am aerial fm aerial digital output auxiliary equipment the cable may be split (using a beolink junction box) in order to accommodate more link rooms. The document enclosed with the cable explains some of the possibilities. The socket may also be used to set up a b...
Page 10
10 bang & olufsen 1 2 when you switch on via the red power switch button a tiny red light appears in the display, indicating that the system is in stand-by mode, ready to be used. Open the glass door (press the load-button). Remove the carton strip behind the cd clamper and the foam packing (these i...
Page 11
11 option 0 option 2 in a fully integrated av system, your beosound 9000 acts as a mere audio source. The sound is reproduced through the speakers in the beovision tv – or, as shown here, through a set of active speakers connected to the tv. The beosound 9000 is automa- tically set to option 0. In a...
Page 12
12 m a i n t e n a n c e a a do not use alcohol or other solvents to clean any part of the beosound 9000! Surfaces before you start cleaning the beosound 9000, we recommend that you open the glass door and then switch off the mains (just push the red power switch button). In this way all surfaces ar...
Page 13
13 handling your cds important! If you experience any problems when trying to play a particular cd always check it for faults (scratches, fingerprints, dust or dirt, etc.). Dust may build up on the cds, especially if you leave them sitting in the beo- sound 9000 for a long time. If there are no visi...
Page 14
14 m i s c l . I n f o r m a t i o n environmental information this bang & olufsen product was delivered in a packing made to protect and transport the product safely from the factory to your home. In the design of our packing we use the most conserving and recyclable materials known to- day, and we...
Page 15
15.
Page 16
3505620 1980 printed in denmark by bogtrykkergården a-s, struer.