Barco DATA 708HS R9002230 Owner's Manual - page 11
3-1
Connections
5975589 BARCODATA 708 HS 080998
3
-9V
SF
HOLD DOWN EHT
STANDBY
-CONV
-17V
+17V
+HTHD
+CONV
+9V
+210V
+30V
123
123
123
COINC
HOLD DOWN HD
32:(50$,16
See installation in-
structions before
connecting to the
supply.
Voir la notice d’inst al-
lation avant de
raccorde r au ré seau.
Vnom 120/230V
IMAX 5/2,5 Amp
FR EQ 60/50 Hz
OFF
ON
-C
O
N
V
-1
7V
ST
AN
D
B
Y
HO
L
D
DO
W
N
E
H
T
SF
HO
L
D
DO
W
N
HD
CO
IN
C
+H
T
H
D
+C
O
N
V
+
210V
-9
V
+
30V
+9
V
+
17V
LED INDICATIONS
RADIATION WARNING
Replacement of critical components of this
apparatus (picture tube and others) can re sult
in excessive X-radiation.
These components are marked in the service
manual by an *.
- Replace only with co nform types
- See service manual fo r high voltage
adjustment instructions. Operating high
voltage for this product is 3 4, 7 KV
WARNING
double pole/neutral f using
For your own safety and to p rotect against
damage alway switch off and un plug before
servicing.
COMM PORT
(800 peripherals)
REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
R-Y
Y(S)
B-Y
RS232 OUT
RS232 IN
IR
"This device complies with Part 15 of the FCC Rules.
Operat ion is subject to f ollowing two con ditions: (1)
this device may not cause harmfull in terference, and
(2) this device must accept any inte rference rece ived,
including interference that may ca use undesired operation."
"This equip ment complies with DHHS radiation
performance standards." (21 cfr. subchapter J)
Made in Belgium by BARCO N V
Noo rdlaan 5 - B-8520 Kuurne
lation avant de
raccorder au réseau.
Vnom 120/230V
IMAX 5/2,5 Amp
FREQ 60/50 Hz
OFF
ON
32:(50$,16
See installat io n in-
structions before
co nnecting to the
su pply.
Voir la notice d’instal-
lat io n avant de
raccorde r au réseau.
Vnom 120/230V
I MAX 5/2,5 Amp
FREQ 60/50 Hz
OFF
ON
-C
O
N
V
-1
7
V
ST
AN
D
B
Y
HO
L
D
DO
W
N
E
H
T
SF
HO
L
D
DO
W
N
H
D
CO
IN
C
+H
T
H
D
+C
ON
V
+2
1
0
V
-9
V
+3
0
V
+9
V
+1
7
V
LED INDICATIONS
RADIATION WARNING
Replacement of critical components of this
apparatus (picture tube and others) can re sult
in excessive X-radiation.
These components are marked in the se rvice
manual by an *.
- Replace only with conform types
- See service manual for high voltage
adjustment instructions. Operating high
voltage for this product is 3 4,7 K V
WARNING
double pole/neutral fusing
For your own safety and to protect aga inst
damage alway switch off and unplug before
servicing.
COMM PORT
(800 peripherals)
REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
R-Y
Y(S)
B-Y
RS232 OUT
RS232 IN
IR
"This device complies with Part 15 of the FCC Ru le s.
Operation is subject to followin g two conditions: (1)
this device may not cause harmfull in terference, and
(2) this device must accept any in terference received,
including int erference that may cause un desired operation."
"This equipment complies with DHHS radiation
performance standards." (21 cfr. subchapter J)
Made in Belgium by BARCO NV
Noordlaan 5 - B-8520 Kuurne
1
3
2
CONNECTIONS
Power (Mains) Cord Connection
Use the supplied power cord to connect your projector to the
wall outlet. Plug the female power connector into the male
connector at the front of the projector.
The projector is switched ON and OFF using the power
(mains) switch ON/OFF.
Pressed : ON
Not pressed : OFF
The projector can start now in the 'operational mode' (image
displayed) or in the 'stand by mode', depending on the position
of the 'power up' dip switch on the controller unit. This DIP
switch is set during installation by a qualified technician. If
you want to change this start up mode, call a qualified
technician.
LEDs on the front plate of the projector
Switching ON/OFF
Signal Input Connection to the Projector :
- Composite Video (*)
- S-Video (*)
- RGBS or RGsB
- RGB3S or RG3sB
- (R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) [component input] (**)
- (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) [component input] (**)
(*) If the line double feature is built in, this feature is available via a software on/off toggle.
(**) If the line double feature is built in, this feature is available for component video signals on standard frequency
via software on/off toggle.