Barco DATA 708HS R9002230 Owner's Manual - page 12
3-2
Connections
5975589 BARCODATA 708 HS 080998
Source No Projector input
Press digit button
1
Comp. Video
1
2
S-Video*/Comp. Video
1
2
3
RGBS or RGsB**
3
3
RGB3S or RG3sB***
4
3
(R-Y)Y(B-Y)S or
(R-Y)Ys(B-Y)****
5
3
(R-Y)Y(B-Y)3S or
(R-Y)Y3s(B-Y)*****
6
32:(50$,16
See installat ion in-
st ruct ions before
connecting to the
supply.
Voir la notice d’inst al-
lation avant de
raccorder au réseau.
Vnom 120/230V
IMAX 5/2,5 Amp
FREQ 60/ 50 Hz
OFF
ON
-C
O
N
V
-17V
ST
A
N
D
B
Y
HO
L
D
D
O
W
N
E
H
T
SF
HO
L
D
D
O
W
N
HD
CO
IN
C
+H
T
H
D
+C
O
N
V
+
2
10V
-9
V
+3
0
V
+9
V
+1
7
V
LED INDICATIONS
RADIATION WARNING
Replacement of critical component s of this
apparatus (picture tube and others) can result
in excessive X-radiation.
These components are marked in t he service
manual by an *.
- Replace only with conf orm types
- See s ervice manual for high voltage
adjus tment inst ruct ions. Operating high
voltage for this product is 34,7 K V
WARN ING
double pole/neutral f using
For your own safet y and t o protect against
damage alway switch off and unplug bef ore
servicing.
COMM PORT
(800 peripherals)
REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
R-Y
Y(S)
B-Y
RS232 OUT
RS232 IN
IR
"This device complies with Part 15 of the FCC Rules.
Operat ion is s ubject to f ollowing t wo conditions: (1)
this device may not cause harmfull interference, and
(2) this device mus t accept any interference received,
including int erference that may cause undesired operat ion."
"This equipment complies wit h DHHS radiation
performance st andards. " (21 cf r. subchapt er J)
Made in Belgium by BARCO NV
Noordlaan 5 - B-8520 Kuurne
TV tuner, e.g. TVDM40 stereo
VCR
Audio amplifier
Composite
video
32:(50$,16
See inst allation in-
structions bef ore
connecting t o the
supply.
Voir la not ice d’instal-
lation avant de
raccorder au réseau.
Vnom 120/230V
IMA X 5/2, 5 Amp
FREQ 60/50 Hz
OFF
ON
-C
O
N
V
-1
7
V
ST
AN
D
B
Y
HO
L
D
D
O
W
N
E
H
T
SF
H
O
L
D
DO
W
N
HD
CO
IN
C
+H
T
H
D
+C
O
N
V
+
210
V
-9
V
+
30V
+9
V
+
17V
LED INDICATIONS
RADIATION WARNING
Replacement of critical components of this
apparatus (pict ure tube and others) can result
in excessive X-radiation.
These components are mark ed in the service
manual by an *.
- Replace only with conform ty pes
- S ee service manual for high volt age
adjustment instructions. Operating high
voltage for this product is 34,7 K V
WARNING
double pole/ neut ral fusing
For your own safety and to protect against
damage alway switc h off and unplug before
servicing.
COMM PORT
(800 peripherals)
REMOTE
R
G(S)
B
S
VIDEO
S-VIDEO
R-Y
Y(S)
B-Y
RS232 OUT
RS232 IN
IR
"This device complies with Part 15 of the FCC Rules.
Operation is subject to following two conditions : (1)
this device may not cause harmfull interference, and
(2) this device must accept any interference receiv ed,
including interference that may cause undesired operation. "
"This equipment complies with DHHS radiation
performance standards." (21 cfr. subchapter J)
Made in B elgium by BARCO NV
Noordlaan 5 - B-8520 Kuurne
VCR S-VHS
Audio amplifier
Luma/Chroma
Connecting a Composite Video Source.
Composite video signals from a VCR, OFF air signal decoder, etc..
If a line doubler is built in :
the default position of this line doubler is OFF (not active).
To enable or to disable this line doubler function, enter the
adjustment mode and change the position of the ON/OFF
toggle switch (see Picture tuning in chapter 'Guided' adjust-
ment mode or 'Random access' adjustment mode).
When the line doubler is ON, the video input signal will be
displayed as a non interlaced image (= improved image
stability).
Video input selection :
press digit button 1 on the RCU
*
Input signal Y/C (luma/chroma)
**
Input signal : R, G and B with composite sync on G or
separate composite sync
***
Input signal : R, G and B with Tri level sync on G or
separate Tri level sync.
****
Input signal : R-Y, Y and B-Y with composite sync on Y
or separate composite sync
*****
Input signal : R-Y, Y and B-Y with Tri level sync on Y or
separate Tri level sync.
1
Video or S-Video : switchable in the Picture Tuning
menu.
Connecting a S-Video or Video Source to Port 2.
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals.
If a line doubler is built in :
the default position of this line doubler is OFF (not active).
To enable or to disable this line doubler function, enter the
adjustment mode and change the position of the ON/OFF
toggle switch (see Picture tuning in chapter 'Guided' adjust-
ment mode or 'Random access' adjustment mode).
When the line doubler is ON, the video input signal will be
displayed as a non interlaced image (= improved image
stability).
Input selection :
press digit button 2 on the RCU