BullFrog A7L Owner's Manual - Time Settings
15
To set the light timer, from the main menu, select
and then
. To change the interior/exterior setting or to set the light
timer, from the main menu, select
and then
To engage the interior lights press the Interior button. To engage
the exterior lights press the Exterior button. To enable the timer,
press the [Light Timer] icon. Set the desired time and duration
or the timer by by pressing on the hour or minute you wish to
adjust. The background color of the selected time will change to
orange. Press the
or icons to choose the desired time and
duration. Press the
icon to confirm your selections. The light
timer will turn on the interior and exterior lights according to the
current Interior and Exterior button positions.
Time Settings
Setting the time of day
Setting the time is important for filtration settings and other
background settings to function as expected. To set the time, from
the main menu, press the
icon, followed by the
icon.
This will bring you to the “Time of Day” menu. Select the correct
time by pressing on the hour or minutes, and then using the
and buttons to select the correct time. Holding the
or
buttons will allow you to more quickly move through time.
Press the
icon to confirm your changes.
Filtration Cycles
Your Spa comes factory programmed to run two cycles in each 24
hour period.
Filter Cycle 1:
Begins at 6:00pm (18:00) and runs for 2
hours. (3 hours for spas equipped with the optional WellSpring
Filtration Pump.)
Filter Cycle 2:
Begins at 8:00am (8:00) and runs for 1 hour.
These factory set filtration cycles should be adequate for light to
normal spa use (spas used once to twice per week). For cases of
more frequent, to heavy spa usage, you may need to increase the
filter cycle durations to maintain water clarity.
Changing Filter Cycles:
To change filter 1 cycle:
From the main menu, press “Settings”
followed by
. This
will take you to the “Filtration” menu. Select the “Filter Cycle 1”
by pressing . Adjust the time and duration by pressing on the
hour or minutes, and then using the
and buttons to select
the correct time and duration. Press the
icon to confirm your
changes.
To change filter 2 cycle:
Select the “Filter Cycle 2” by pressing . Adjust the time and
duration by pressing on the hour or minutes, and then using the
and buttons to select the correct time and duration. Press
the
icon to confirm your changes.
Purge Cycles
In order to maintain sanitary conditions and protect against
freezing, your spas pumps will purge water from their respective
plumbing by running all pumps at the beginning of each filter
cycle. If the Filter Cycle 1 is set for 24 hours, enabling Filter
Cycle 2 will initiate a purge when Filter Cycle 2 is scheduled to
begin.
To Change Preferences
To change temperature display between Fahrenheit (F) and
Celsius (C), 24 or 12 hour clock :
From the main menu, press
. In the Settings menu press the
key to move to the second page of the menu. Press the
icon. The “Units” menu will then be displayed. To change the
temperature setting, press the temperature unit which is currently
displayed. This will change it from C° to F° or vice versa.
To change the time display press on the currently selected hour
unit.
To Set Reminders
From the main menu, press
, then in the “Settings” menu,
press the
icon. Next, press the portion of the panel where
“Yes” or “No” is displayed. This will toggle the reminders to
trigger, or turn them off.
Hold
The “Hold” function prevents the jets from running to allow
JetPaks to be swapped out. By default, a hold lasts 60 minutes, or
until the
button is pressed
.
Restricting Operation
The control panel can be restricted to prevent unwanted use or
temperature adjustments. “Panel Lock” prevents most functions
on the controller from being used, while all automatic functions
remain active. “Lock Settings” in contrast, allows the jets and
lighting to be adjusted, while other features are inactive.
To lock the settings, from the Main Menu
Press
, followed by
. The “Settings” lock and ”Panel”
lock options will be displayed in the menu. To lock press and
hold “Lock” for 5-8 seconds to lock the settings in their current
configuration, or press and hold
for 5-8 seconds to lock
the panel. While the panel is locked, the only buttons that will
function are the buttons that lead to the locking screen.
To cancel either of the lock settings, navigate to the Lock
menu by pressing
followed by
. Press and hold the
corresponding icon for 5-8 seconds to release the lock.
GFCI TEST
The installer can cause the GFCI Trip Test to occur sooner by
initiating manually. To initiate the test press the
icon. In
the Settings menu press the key to move to the second page
of the menu. Press
, this will bring up the “Utilities” menu.
Press
. In the “GFCI Test” menu you will see the
status of the GFCI test. If the GFCI test has not been