BullFrog A7L Owner's Manual - Sensor-Related Messages
50
Sensor-Related Messages
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour. Call for Service.
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
Miscellaneous Messages
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
No Communications
The control panel is not receiving communication from the System. Call for Service.
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
Pre-Production Software
The Control System is operating with test software. Call for Service.
Sensor-Related Messages
Miscellaneous Messages
READY
RANGE FLTR1
Sensor Balance is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
Sensor Balance is Poor*
The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour.
Call for Service.
Sensor Failure – Sensor A, Sensor B
A temperature sensor or sensor circuit has failed. Call for Service.
READY
RANGE FLTR1
No Communications
The control panel is not receiving communication from the System. Call for Service.
Pre-Production Software
The Control System is operating with test software. Call for Service.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
°F or °C is replaced by °T
The Control System is in Test Mode. Call for Service.
System-Related Messages
System-Related Messages
Memory Failure - Checksum Error*
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the fi rmware (operation
program) and requires a service call.
Memory Failure - Clock Error*
Contact your dealer or service organization.
GFCI Failure - System Could Not Test/Trip the GFCI
NORTH AMERICA ONLY. May indicate an unsafe installation. Contact your dealer or service organization.
A Pump Appears to have been Stuck ON when spa was last powered
POWER DOWN THE SPA. DO NOT ENTER THE WATER.
Contact your dealer or service organization.
A Pump Appears to be Stuck ON
Water may be overheated. POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your dealer or service organization.
Confi guration Error – Spa will not Start Up
Contact your dealer or service organization.
Memory Warning - Persistent Memory Reset*
Appears after any system setup change. Contact your dealer or service organization if this message appears on more than
one power-up, or if it appears after the system has been running normally for a period of time.
* This message can be reset from the topside panel with any button press.
Memory Failure Checksum Error*
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the fi rmware (operation program) and
requires a service call.
System-Related Messages
Memory Failure - Checksum Error*
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the fi rmware (operation
program) and requires a service call.
Memory Failure - Clock Error*
Contact your dealer or service organization.
GFCI Failure - System Could Not Test/Trip the GFCI
NORTH AMERICA ONLY. May indicate an unsafe installation. Contact your dealer or service organization.
A Pump Appears to have been Stuck ON when spa was last powered
POWER DOWN THE SPA. DO NOT ENTER THE WATER.
Contact your dealer or service organization.
A Pump Appears to be Stuck ON
Water may be overheated. POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your dealer or service organization.
Confi guration Error – Spa will not Start Up
Contact your dealer or service organization.
Memory Warning - Persistent Memory Reset*
Appears after any system setup change. Contact your dealer or service organization if this message appears on more than
one power-up, or if it appears after the system has been running normally for a period of time.
* This message can be reset from the topside panel with any button press.
Memory Warning Persistent Memory Reset*
Appears after any system setup change. Contact your dealer or service organization if this message appears on more than one
power-up, or if it appears after the system has been running normally for a period of time.