1. DL manuals
  2. Bungard
  3. Cutter
  4. NE-CUT
  5. Original Instructions Manual

Bungard NE-CUT Original Instructions Manual

Manual is about: Board Cutter

Summary of NE-CUT

  • Page 1

    Ne-cut-manual-e page 1 / 10 board cutter ne-cut translation of the original instruc- tions ➔ read before use ➔ pay heed to all safety regulations ➔ keep at a safe place to refer to in the future table of content description........................................................2 features..............

  • Page 2: Ne-Cut-Manual-E

    Ne-cut-manual-e page 2 / 10 description ne-cut is designed to cut fr4 pcb boards up to 3.0 mm or aluminium up to 2 mm thickness. Depending on customer application cutting of steel (depending on the alloy up 0.8 mm) and plastic (up to 5 mm) is also possible same as paper or film material. The transpa...

  • Page 3: Ne-Cut-Manual-E

    Ne-cut-manual-e page 3 / 10 eg-declaration of conformity eg-konformitätserklärung/declaration of conformity hersteller / supplier: bungard elektronik gmbh & co. Kg rilkestraße 1 51570 windeck germany bevollmächtigte person für die zusammenstel- lung der technischen unterlagen: person in charge jürge...

  • Page 4: Ne-Cut-Manual-E

    Ne-cut-manual-e page 4 / 10 intended use ne-cut is specially designed to cut fr4 pcb boards up to 3.0 mm or aluminium up to 2 mm thickness. Depending on customer application cutting of steel (depending on the alloy up 0.8 mm) and plastic (up to 5 mm) is also possible same as paper or film material. ...

  • Page 5: Ne-Cut-Manual-E

    Ne-cut-manual-e page 5 / 10 set up take over from the transport agent after receiving and unpacking check the machine for possible transport damages. In case of transport damage, please inform your insurance, the transport company and the manufacturer / supplier. Transport to operation site only use...

  • Page 6: Ne-Cut-Manual-E

    Ne-cut-manual-e page 6 / 10 turn the lever up and back to its home position. Take a wide board and scoop it first against the front side counter bar and then against the rear counter bare. Pull the lever until the clamping unit fixes the board. In this position you can adjust the height of the rear ...

  • Page 7: Ne-Cut-Manual-E

    Ne-cut-manual-e page 7 / 10 after you removed clamping unit and table you see a square pipe which holds the lower blade (picture 6). You can reach the attach- ment screws through the big top holes. Loosen the screws and take out the square pipe with the lower blade. If you unfasten the screw couplin...

  • Page 8: Ne-Cut-Manual-E

    Ne-cut-manual-e page 8 / 10 tighten the attachment screws of the holder just slightly and move the holder with the lower blade evenly against the template that lies before the upper blade. Tighten the attachment screws hand firm. Now loosen the counter nuts of the headless screws and turn these scre...

  • Page 9: Ne-Cut-Manual-E

    Ne-cut-manual-e page 9 / 10 cleaning and maintenance after use clean the machine from dust and chips by vacuuming especially the blades and behind the blades. Do not use compressed air to clean the machine from fr4 dust because then the fibre glass fibres are dispensed all over the room. You can cle...

  • Page 10: Ne-Cut-Manual-E

    Ne-cut-manual-e page 10 / 10 guarantee all machines are submitted before distribution to examination on function and continuous operation firm- ness. On the machine we grant a work warranty of 12 months to our customers starting from purchase date on accuracy in material and processing. We warrant a...