1. DL manuals
  2. Cabletron Systems
  3. Switch
  4. MicroMMAC-22ES
  5. Reference Manual

Cabletron Systems MicroMMAC-22ES Reference Manual

Other manuals for MicroMMAC-22ES: Installation Manual, User Manual, Installation Manual
Manual is about: 10BASE-T INTELLIGENT STACKABLE HUB

Summary of MicroMMAC-22ES

  • Page 1

    Title page m icro mmac local management routing addendum.

  • Page 3: Notice

    Micrommac local management routing addendum i notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been ...

  • Page 4

    Notice ii micrommac local management routing addendum.

  • Page 5: Contents

    Micrommac local management routing addendum iii contents 1.0 introduction..................................................................................... 1 1.1 local management overview ......................................................... 1 2.0 m icro mmac protocol support....................

  • Page 6

    Contents iv micrommac local management routing addendum.

  • Page 7: 1.0

    Micrommac local management routing addendum 1 1†22† 1.0 introduction welcome to cabletron systems micrommac local management routing addendum. The purpose of this document is to assist the user to configure the micrommac for routing. Use this document as a guide in local management routing. The micr...

  • Page 8: 2.0

    M icro mmac protocol support 2 micrommac local management routing addendum 2.0 m icro mmac protocol support the following sections discuss protocol support on the micrommac including wan protocols, data compression, bridging and routing, and protocol filtering. 2.1 wan protocols the micrommac, with ...

  • Page 9: 2.3

    Bridging and routing micrommac local management routing addendum 3 2.3 bridging and routing bridging — bridging creates separate segments on a network. The bridge examines a portion of each network frame called the header. This header contains control information for the frame. The bridge compares t...

  • Page 10: 2.3.1

    M icro mmac protocol support 4 micrommac local management routing addendum 2.3.1 micrommac bridging and routing the micrommac can operate as a bridge, a router, or both. The micrommac operates as a router for network protocols that are supported when routing is enabled and operates as a bridge when ...

  • Page 11: Tcp/ip

    Protocol filtering micrommac local management routing addendum 5 ip routing — ip routing support provides the ability to process tcp/ip frames at the network layer for routing. Ip routing support includes the routing information protocol (rip) that allows the exchange of routing information on a tcp...

  • Page 12

    M icro mmac protocol support 6 micrommac local management routing addendum bridge filtering bridge filtering enables a network administrator to control the flow of packets across the micrommac. Bridge filtering can be used to “deny” or “allow” packets based on a “matched pattern” using a specified p...

  • Page 13: 3.0

    Local management organization micrommac local management routing addendum 7 3.0 m icro mmac local management a general working knowledge of basic network operations and an understanding of management applications are helpful prior to using cabletron systems local management. The following sections c...

  • Page 14: 3.2

    M icro mmac local management 8 micrommac local management routing addendum 3.2 router setup screen figure 3-2 shows the router setup screen which enables you to display either the ip router setup screen or the ipx router setup screen to configure the micrommac ports for ip or ipx routing. Figure 3-2...

  • Page 15: 3.3

    Ip router setup screen micrommac local management routing addendum 9 3.3 ip router setup screen the ip router setup screen enables you to access the ip general config and ip rip screens to configure the micrommac for ip routing and enable rip on the micrommac. Access the ip router setup screen, show...

  • Page 16: 3.3.1

    M icro mmac local management 10 micrommac local management routing addendum 3.3.1 the ip router setup screen fields the following list describes each of the router setup screen fields: ip general config use this field to access the ip general config screen and configure the micrommac for ip routing....

  • Page 17: 3.4.1

    The ip general config screen micrommac local management routing addendum 11 3.4.1 ip general configuration status fields the following list describes each of the ip general configuration status fields. The status fields are for informational purposes only and cannot be modified. Router name displays...

  • Page 18: 3.4.2

    M icro mmac local management 12 micrommac local management routing addendum interf. Type displays the type of interface used by the specified port. Oper status displays the operational status of the selected port. 3.4.2 ip general configuration fields this section provides a general overview of the ...

  • Page 19: 3.4.3

    The ip general config screen micrommac local management routing addendum 13 ip routing use this field to enable ip routing services. Ip forwarding use this field to enable ip forwarding. Proxy arp use this field to enable proxy address resolution protocol (arp). 3.4.3 selecting a port for configurat...

  • Page 20: 3.4.5

    M icro mmac local management 14 micrommac local management routing addendum to enter the subnet mask for a router port, complete the following steps: 1. Use the arrow keys to highlight the mask field. 2. Enter the subnet mask (using ddn format) for the ip address that you assigned. 3.4.5 selecting t...

  • Page 21: 3.4.7

    The ip general config screen micrommac local management routing addendum 15 3.4.7 enabling ip routing services on a port the ability to switch ip routing services on and off on a port-by-port basis, provides great flexibility. On the same device, some ports can be routing ip traffic while other port...

  • Page 22: 3.4.9

    M icro mmac local management 16 micrommac local management routing addendum 3.4.9 configuring the udp broadcast redirector in order to locate a server that can provide a particular network service, many ip hosts rely on the use of lan broadcasts to send udp service requests. The udp port number cont...

  • Page 23: 3.4.10

    The ip general config screen micrommac local management routing addendum 17 to configure the udp broadcast redirector, complete the following steps: 1. Use the arrow keys to highlight the udp port field under system level setup. 2. Enter the udp port number of the udp service request packets that yo...

  • Page 24: 3.4.11

    M icro mmac local management 18 micrommac local management routing addendum a proxy arp response is generated when the following occurs: • proxy arp is enabled on a router port. • an arp request is received as a lan broadcast (looking for the mac-layer address of an ip host on another network segmen...

  • Page 25: 3.4.12

    The ip general config screen micrommac local management routing addendum 19 3.4.12 enabling the rip routing protocol on a port routing information protocol (rip) is a widely implemented routing protocol that is used extensively on ip internetworks. Ip routing services uses the rip routing protocol t...

  • Page 26: 3.5

    M icro mmac local management 20 micrommac local management routing addendum figure 3-5 ip rip configuration screen 3.5 ipx router setup screen the ipx router setup screen enables you to access the ipx general config, ipx rip, and ipx sap screens to configure the micrommac for ipx routing and enable ...

  • Page 27: 3.5.1

    Ipx router setup screen micrommac local management routing addendum 21 figure 3-6 ipx router setup screen 3.5.1 the ipx router setup fields the following list describes each of the ipx router setup screen fields: ipx general config use this field to access the ipx general configuration screen and co...

  • Page 28: 3.6

    M icro mmac local management 22 micrommac local management routing addendum 3.6 the ipx general configuration screen the ipx general config screen enables you to configure the micrommac for ipx routing. Access the ipx general configuration screen by using the arrow keys to highlight the ipx general ...

  • Page 29: 3.6.2

    The ipx general configuration screen micrommac local management routing addendum 23 uptime displays the amount of time elapsed since the last time the micrommac was rebooted. Version the version number of the ipx routing used on the micrommac. Adminstatustime displays the amount of time elapsed sinc...

  • Page 30: 3.6.2.1

    M icro mmac local management 24 micrommac local management routing addendum ipx routing use this field to enable ip routing services. Ipx forwarding use this field to enable ipx forwarding. 3.6.2.1 selecting a port for configuration routing services enables you to choose the ports that you want to c...

  • Page 31: 3.6.2.3

    The ipx general configuration screen micrommac local management routing addendum 25 3.6.2.3 selecting the frame type for a port on each port, frame type specifies the format of the frame in which ipx packets are encapsulated for transmission. The frame type options available for each router port are...

  • Page 32: 3.6.2.5

    M icro mmac local management 26 micrommac local management routing addendum 3.6.2.5 enabling ipx routing services on a port the ability to switch ipx routing services on and off on a port-by-port basis, provides great flexibility. On the same device, some ports can be routing ipx traffic while other...

  • Page 33: 3.6.2.7

    The ipx general configuration screen micrommac local management routing addendum 27 3.6.2.7 enabling the ipx sap routing protocol on a port ipx source advertisement protocol (sap) is used by ipx to exchange information about novell service providing nodes, such as file servers and print servers that...

  • Page 34: 3.6.2.8

    M icro mmac local management 28 micrommac local management routing addendum figure 3-8 ipx sap configuration screen 3.6.2.8 enabling the rip routing protocol on a port ipx rip (routing information protocol) is widely implemented and used extensively on ipx internetworks. Ipx routing services use the...

  • Page 35

    The ipx general configuration screen micrommac local management routing addendum 29 to enable rip routing, complete the following steps: 1. From the ipx router setup screen, highlight ipx rip andpress enter. The ipx rip configuration screen, shown in figure 3-9, displays. 2. Use the arrow keys to hi...

  • Page 36

    M icro mmac local management 30 micrommac local management routing addendum.

  • Page 37: Index

    Micrommac local management routing addendum index-1 index b bootstrap protocol client 16 bootstrap protocol server 16 bridge filtering 6 bridging 3 bridging and routing 3, 4 c configuring the network broadcast type on a port 18 configuring the udp broadcast redirector 16 d data compression 2 domain ...

  • Page 38

    Index index-2 micrommac local management routing addendum r rip 19, 28 routing 3 routing information protocol (rip) 10, 19 s selecting a port for configuration ip 13, 24 simm 1 sunrpc (nis) 16 t tacacs-database service 16 time 16 trivial file transfer 16 u udp bootstrap protocol client 16 bootstrap ...