- DL manuals
- Cabletron Systems
- Network Hardware
- MMAC-M3FNB
- Overview And Setup Manual
Cabletron Systems MMAC-M3FNB Overview And Setup Manual
Summary of MMAC-M3FNB
Page 1
Mmac-m3fnb multi-media access center overview and setup guide the complete networking solution ™.
Page 3: Notice
Notice i notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or soft...
Page 4: Fcc Notice
Notice ii fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Not...
Page 5: Vcci Notice
Notice iii vcci notice this equipment is in the 1st class category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the voluntary control council for interference by information technology equipment (vcci) aimed at preventing radio interfe...
Page 6
Notice iv.
Page 7: Contents
Contents v contents chapter 1 introduction 1.1 using this manual .................................................................... 1-1 1.1.1 symbols.......................................................................... 1-2 1.2 using the mmac-m3fnb manual set .....................................
Page 8
Contents vi.
Page 9: Chapter 1
Introduction page 1-1 chapter 1 introduction the mmac-m3fnb™ multi-media access center offers flexibility and convenience in the design and operation of your network. The enclosure can contain a repeater/management module and up to two media interface modules (mims™). This manual is an installation ...
Page 10
Introduction page 1-2 1.1.1 symbols throughout this manual you will see two symbols which will be used to call your attention to important safety-related information: you will also see a third symbol, which will be used to call your attention to additional information not related to safety: 1.2 usin...
Page 11
Introduction page 1-3 1.3 getting help if you need additional support related to the mmac-m3fnb, or if you have any comments, suggestions, or questions concerning this manual, contact cabletron systems technical support. Before calling, please have the following information ready: • the product type...
Page 12
Introduction page 1-4 and standard aui transceiver cable. Each media type has a variety of mims, which, when installed into the mmac-m3fnb, are compatible with all other mims installed in that mmac-m3fnb. You can have complete network integration of a variety of media through a single source. The mm...
Page 13
Introduction page 1-5 universal power supply the mmac-m3fnb power supply senses and automatically adjusts to the input voltage and frequency. It is designed to operate at 110 or 220 volts without any user configuration. Built-in power supply protection the power supply module automatically powers do...
Page 14
Introduction page 1-6 rack mountable chassis the mmac-m3fnb chassis can be mounted into a standard 19" (48.26 cm) equipment rack. Separate rack mount brackets are included that allow the unit to be flush mounted or recessed from the front plane of the rack mount unit for safety and ease of network c...
Page 15: Chapter 2
Installation requirements and specifications page 2-1 chapter 2 installation requirements and specifications this chapter describes the following: • site guidelines that must be met before installing an mmac-m3fnb onto your network • mmac configuration guidelines • operating specifications for the m...
Page 16
Installation requirements and specifications page 2-2 2.2 mmac-m3fnb configuration guidelines the mmac-m3fnb has three slots: two that accept media interface modules, or mims; and one for a management module. The slots are numbered from bottom to top; slot #1 is a half-width slot reserved for the ma...
Page 17
Installation requirements and specifications page 2-3 power supply module requirements the mmac-m3fnb power supply senses and automatically adapts to the input voltage and frequency. The unit is designed to be operated at 110 or 220 volts without user configuration. Input frequency: 47 to 63 hz inpu...
Page 18: M3Psm
Installation requirements and specifications page 2-4 figure 2-1. The mmac-m3psm leds ok when lit, this green led indicates that the (power supply) power supply module is operating correctly; a signal is also sent to the management/repeater module to indicate that the power supply is functioning pro...
Page 19
Installation requirements and specifications page 2-5 fan tray led this led is green when both the fans are (fan tray) operating properly. The led turns red when either fan slows to half speed or less, and signals the management/repeater module that there is a fan tray problem. Safety designed in ac...
Page 20
Installation requirements and specifications page 2-6.
Page 21: Chapter 3
Mmac-m3fnb setup page 3-1 chapter 3 mmac-m3fnb setup this chapter contains instructions to help you set up cabletron systems’ mmac-m3fnb. You will not need any special tools or equipment to set up the mmac-m3fnb, but you must follow all guidelines listed in chapter 2, installation requirements and s...
Page 22
Mmac-m3fnb setup page 3-2 3.2.1 rack mounting the mmac-m3fnb to mount the mmac-m3fnb in a standard 19" equipment rack: 1. Using a phillips head screwdriver, remove the four screws (item 1, figure 3-1) – two on each side of the mmac-m3fnb – which are closest to the front of the mmac-m3fnb, and set th...
Page 23
Mmac-m3fnb setup page 3-3 3. Insert the screws through the holes on the mounting bracket and into the screw holes on the mmac-m3fnb. 4. Tighten the screws until the mounting bracket is securely attached to the unit. 5. Repeat steps 2-4 for the second rack mount bracket. Be sure to use the same set o...
Page 24
Mmac-m3fnb setup page 3-4 1. Slide the cable tie tray (figure 3-2) into the rack. 2. Align the slots on each mounting bracket on the tray with the desired holes on the equipment rack. Figure 3-2. Cable tie tray installation 3. Insert bolts through the slots in each of the mounting brackets and into ...
Page 25
Mmac-m3fnb setup page 3-5 3.2.3 inserting the fan tray the mmac-m3fnb is equipped with a removable fan tray that allows for easy periodic cleaning and/or replacement if a problem occurs with fan operation. To insert the fan tray in the mmac-m3fnb: 1. Hold the fan tray (see figure 3-3, below) with th...
Page 26
Mmac-m3fnb setup page 3-6 if this led remains red, it indicates that one or both of the fans is not operating at the proper speed. Check the fan tray to ensure that nothing is interfering with movement of the fans. If you cannot find the problem, call cabletron systems technical support for assistan...
Page 27
Mmac-m3fnb setup page 3-7 b. With the leds at the top of the m3psm and the handle to the right, align the m3psm with the slotted paths on the top and bottom of the opening. C. Ensuring that the power supply is inserted into the slotted paths, carefully slide the module forward until it is connected ...
Page 28
Mmac-m3fnb setup page 3-8 or mims. Refer to the applicable module manuals for more information about mim installation; see below for power-up instructions. 3.2.5 powering up the mmac-m3fnb power up the mmac-m3fnb as follows: 1. If the mmac-m3fnb will not be rack mounted, place it on the selected sit...