Cambridge Audio azur 551R V2 User Manual - page 7
551R V2
azur
7
ENGLISHENGLISH
Remote control
Enter
Used in the OSD setup menus.
Stereo modes
Selects Stereo or Stereo + Sub modes for Analogue or Digital
sources (digitally processed).
Surround modes
Selects digital surround processing modes and various matrix
encoded surround processing modes for analogue or digital
sources (digitally processed).
Analogue Stereo Direct
Press to listen directly to the analogue inputs for the current
source directly with no analogue to digital conversion or DSP
processing for highest possible stereo sound quality.
Audio In Type
Switches the audio between the types available for the
current source. Depending on the source selected and
whether you have assigned an HDMI input to it, Analogue,
Digital and HDMI can be available.
Stereo Mono
When listening to FM, press to alternate between stereo and
mono modes.
Mode
Press to select Auto/Manual or Preset tuning when in Tuner
mode.
Store
Press to store the current frequency when in Tuner mode.
The 551R V2 is supplied with an Azur Navigator remote
control. Insert the supplied AAA batteries to use. For full
details of the various adjustment functions available from the
remote, refer to the later sections of this manual.
Backlight button
Press to turn the backlight on and illuminate the remote
control buttons. Press and hold for a few seconds (all buttons
will initiate a rapid flashing) to enable backlight function by
pressing any buttons on the remote. Press and hold again to
disable function and revert to default.
Mute
Mutes the audio on the AV Receiver. Press again to cancel
mute.
Standby/On
Switches the unit between Standby mode and On.
Tuner, BD/DVD, CD/Video 1, Video 2,
Aux/TV, Vid 3/MP3, Tape/MD/CDR
Press the corresponding button to change the input source.
Pressing the Tuner AM/FM button a second time toggles
between AM and FM modes.
Pressing the Aux/TV button a second time if ARC is enabled
on your TV (see later section) selects TV-ARC (Audio Return
Channel).
The above button descriptions are naturally brief. Please
refer to the 'Operating Instructions' section of this manual
for more information on the relevant functions implemented.
7.1 Direct
Selects the 5.1/7.1 direct input source.
HDMI preview
Press to see the previews of different HDMI sources
connected to the unit. Use the ▲▼ buttons to navigate. See
later section of the manual.
On-Screen Display (OSD)
Press to turn on and off the on-screen setup menus for
display on your monitor/screen.
Note: The output for OSD is only available through HDMI 1.
Info
Press to view the current source material and decoding
mode. Press again whilst the current decoding mode is
scrolling (as long as mute is not on) to display the incoming
sample rate. When listening to FM with RDS, press to cycle
round various RDS information modes.
Bass/Treble
Press for bass/treble adjustment, using the Volume up/down
buttons. Note: Bass/Treble is bypassed in analogue stereo
direct and 7.1 direct modes.
Lip sync
Press to activate and adjust the lip sync delay function if the audio and video
appear out of sync. While the Lip sync delay status is shown on the units
display, use the Vol knob on the front panel or the ◄ and ► buttons on the
remote to adjust the delay time. Adjusting the value to zero causes lip sync
delay to be turned off. See later section in this manual.
Volume
Increase or decrease the volume of the AV receiver output.
/
▲▼◄► Navigational button
Press the
buttons to select different input sources and the ◄► buttons
to change tuner preset. Use the ◄►▲▼ buttons to navigate within the
OSD setup menus.
Stereo/
Mono
Mode
Tuner