CAME GARD 4 SERIES Installation manual - page 27
Pa
g
e
2727
-
M
an
u
al
c
od
e:
11
9
G
U
5
5
11
9
G
U
5
5
ve
r.
1.
1
01
/2
01
2
© C
A
M
E c
an
ce
lli auto
m
ati
ci
s.p.a. - T
h
e d
ata a
n
d i
nf
or
m
ati
on
in
th
is
m
an
u
al
m
ay b
e c
h
an
g
ed at a
ny tim
e a
n
d w
ith
ou
t o
b
lig
ati
on
o
n th
e p
art of C
am
e C
an
ce
lli A
uto
m
ati
ci
S
.p.a. to n
otify s
ai
d c
h
an
g
es.
ENGLISH
On its premises, CAME Cancelli Automatici S.p.A. implements a certified Environmental Management System in compliance with
the UNI EN ISO 14001 standard to ensure environmental protection.
Please help us to safeguard the environment. At CAME we believe this to be one of the fundamentals in its market operations and deve-
lopment strategies. Just follow these short disposal instructions:
DISPOSING OF THE PACKAGING
The components of the packaging (that is, cardboard, plastic, and so on) are solid urban waste and may be disposed of without much
trouble, simply by separating them for recycling.
Before proceeding it is always a good idea to check your local legislation on the matter.
DO NOT DISPOSE OF IN NATURE!
PRODUCT DISPOSAL
Our products are made up of various materials. Most of these (aluminium, plastic, iron, electric cables) are solid urban waste. Can be
recycled by separating
and
Other components (i.e. electronic cards, remote control batteries, etc. ) may contain hazardous substances.
These must therefore be handed over the specially authorised disposal firms.
Prima di procedere è sempre opportuno verificare le normative specifiche vigenti nel luogo di smaltimento.
DO NOT DISPOSE OF IN NATURE!
PROBLEM
REFERENCE
CHECK
The operator neither opens nor closes
1-2-3-4-6-8-18
1 - Lock the inspection hatch using the key and check the
release lock
The operator opens but does not shut.
4-7-10
2 - Deactivate the Maintained action function via Dip-switch
The operator closes but does not open
4-7-9
3 - Check power source and fuses
The operator does not carry out the automatic
closing
11-12-13
4 - The N.C. safety contacts are open
The radio-control does not work
2-14-16
6 - Deactivate the master-slave function
The operator inverts the direction of travel
7-18
7 - Check balancing and tighteness of springs
Only one radio-control works.
22
Deactivate the obstacle detection function via dip switch
The photocell does not work
12-23-24
9- Check opening limit-switch
The led warning light flashes quickly
4
10- Check closing limit-switch
The led warning light stays lit.
13
11 - chiusura automatica.” the Dip-switches
The operator does not fully complete cycle
7
12 - Check for the proper direction of travel
Cannot balance the arm
7-15
13 - Check the command devices
The operator does not decelerate
7-15
14 - Cut off and bring back power to card or check the TOP/
TAM jumper on the AF43S card
The operator does not run on the emergency
batteries
8-25-26
15 - Check the Arm length/Applied Accessories ratio”
The operator is slow when starting
7
Memorise the radio code again
18 - Adjust sensitivity
22 - Insert or duplicate the same code in all transmitters
23 - Activate the photocell via Dip-switch
24 - Connect the photocells in series and not in parallel
fashion
25 - Check the batteries
26 - Respect the polarities when powering up the photocells
Dismantling and disposal
Trouble shooting