Campbell Hausfeld PS230B Operating And Assembly Instructions Manual - Airless Paint Sprayers
excess of those specified by the
manufacturer.
●
Do not use the hose as a strength
member to pull or lift the
equipment.
●
Always wear appropriate gloves, eye
protection, and a respirator or mask
when painting.
●
Always work in a clean environment.
Do not aim the spray gun at any
dust or debris.
●
Do not operate or spray near
children. Keep children, pets, and
visitors away from equipment and
work area at all times.
●
Do not over reach or stand on an
unstable support. Keep effective
footing and balance at all times.
●
Stay alert and watch what you are
doing.
●
Do not operate the equipment when
fatigued or under the influence of
drugs or alcohol.
FAIlUrE TO FOllOw
ThESE INSTrUCTIONS
CAN rESUlT IN
SErIOUS INjUry
INClUDING DEATh.
5
Operating Instructions and Assembly Instructions
Beforeservicingorresting:
1. Turn the Prime/Spray Control to the
PRIME position.
2. Turn the pressure control to LOW
PRESSURE/HYDRAULIC BLEEDING
position.
3. Turn power switch to OFF position.
4. With gun pointed in a safe direction,
pull the gun trigger, with the
trigger lock disengaged.
5. Engage trigger lock.
●
Simply turning off the pump motor
will not relieve pressure from
system. The above procedure MUST
be followed.
FIrE Or ExPlOSION hAzArD:
●
Do not use solvents with flash points
less than 70°F (21°C) to clean this
equipment (examples of acceptable
cleaning solvents are water, mineral
spirits, lacquer thinner, Xylene and
high flash napha. A partial example
list of unacceptable cleaning
solvents are low flash napha, mek,
acetone, alcohol and toluene).
●
Use only conductive or grounded
high-pressure airless paint sprayer
hoses specified by the manufacturer.
●
Verify that all containers and
collection systems are grounded to
prevent static discharge.
●
Do not spray pump assembly.
●
Have fire extinguisher equipment
present and working.
Donotsprayflammable
materialsinvicinityof
openflameornearignition
sources.Motors,electricalequipment
andcontrolscancauseelectricalarcs
thatwilligniteaflammablegasor
vapor.Neverstoreflammableliquidsor
gasesinthevicinityoftheunit.
Donotsprayacids,
corrosivematerials,
toxicchemicals,fertilizersorpesticides.
usingthesematerialscouldresultin
deathorseriousinjury.
●
Do not use fuels to clean this
equipment.
●
Keep spray area well ventilated.
Keep a good supply of fresh air
moving through the spray area.
●
Remove all ignition sources (i.e.
Static electricity, pilot lights,
cigarettes and electrical arcing).
●
Airless spraying can cause static
electricity. Always ground the pump
and spraying surface. Always use a
3-wire grounded extension cord and
power receptacle.
●
Do not use paints or solvents
containing halogenated
hydrocarbons such as methyl
bromine, carbon tetrachloride, and
ethyl iodine.
Keephoseaway
fromsharpobjects.
Burstinghosesmaycauseinjury.
Examinehosesregularlyandreplaceif
damaged.
●
Check hoses for weak or worn
condition before each use, making
certain that all connections are
secure.
●
Keep area clean and free of paint or
solvent containers, rags, and other
flammable materials.
TO rEDUCE ThE rISk OF INjUry:
●
Do not spray acids,
corrosive materials, toxic
chemicals, fertilizers, or
pesticides. Using these
materials could result in
death or serious injury.
●
Do not kink or over-bend the hose.
●
Do not expose the hose to
temperatures or to pressures in
Airless Paint Sprayers
www.chpower.com