Candy CBT 66 User Instructions - page 19
with the cabinet door and adjust spacer E using screws P (fi g.
2), then ensure the appliance meets the cabinet at the rear.
• Extraction through an outside wall
The appliance expels the fumes through an outside wall or a
duct. It is necessary to buy a telescopic pipe in accordance
with the standards in use (infl ammable) and connect it to
fl ange B (Fig 3).
Remove the charcoal fi lters already fi tted to the appliance by
turning them 90° anticlockwise (Fig. 7).
• Recirculation
The clean air is returned into the room through a connecting
tube passing inside the cupboard and connected to the ring
B (fi g 4).
The charcoal fi lters are already fi tted to the appliance.
USE AND MAINTENANCE
•We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The eff ective performance of the cooker hood depends on
constant maintenance; the anti-grease fi lter and the active
carbon fi lter both require special attention.
• The anti-grease fi lter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the fi lter to become saturated depends on
the way in which the appliance is used).
The acrylic fi lter, which is found resting on the grille, should
be replaced when the text, visible through the grille, changes
colour and the ink spreads; the new fi lter should be fi tted in
such a way that the text can be seen through the grille from
outside the cooker hood.
If the fi lters do not have any text on them, or if metal fi lters
or aluminium panel fi lters are used, they should be washed
every 2 months in order to prevent the risk of fi re. To wash the
fi lters, proceed as follows:
- Remove the fi lter from the grille and wash it using a solu-
tion of water and neutral liquid detergent, leaving the dirt
to soften.
- Rinse thoroughly with warm water and leave to dry.
The metal fi lters and/or aluminium panel are also dishwasher
safe. If the fi lters are made using aluminium, or if an aluminium
panel is used, after a few washes the colour may change. This
does not mean they have to be replaced.
If the replacement and washing instructions are not followed,
the anti-grease fi lters may present a fi re hazard.
• The active carbon fi lters are used to purify the air which
is released back into the room. The fi lters are not washable
or re-usable and must be replaced at least once every four
months. The active carbon fi lter saturation level depends on
the frequency with which the appliance is used, the type of
cooking performed and the regularity with which the anti-
grease fi lters are cleaned.
• Remove build-up from the fan and other surfaces of the
cooker hood regularly using a cloth moistened with denatured
alcohol or non-abrasive neutral liquid detergent.
• The light on the cooker hood is designed for use during cook-
ing and not for general room illumination. Extended use of the
light reduces the average duration of the bulb.
• Commands: (Fig.8) Slider the key symbols are explained
below:
This hood is fitted with a microswitch which allows the
activation of the motor speed) through the opening of the
telescopic undercarriage. If the telescopic undercarriage is
closed the motor speeds cannot be activated.
This microswitch does not have an impact on the activation of
the lights which must be switched on through the appropriate
switch (see fi g.8A).
A = Light switch
A1 = Off key
A2 = On key
B = Speed control
B1 = FIRST SPEED key
B2 = SECOND SPEED key
B3 = THIRD SPEED ke
Warning! If the telescopic undercarriage is closed with
the speed set at 2,, once it is re-opened, the hood will be
reactivated with the same speed in use when the hood was
closed.
• Replacing incandescent light bulbs (Fig. 1A).
To remove the incandescent light bulb, take out the grease
fi lters as described in (Fig. 6) and remove the bulb.
Replace it with a new one of the same type (Fig. 1A).
CUSTOMER ASSISTANCE SERVICE
Before contacting the Technical Assistance Service:
If the product does not operate at all, we advise you to:
- check that the plug has been inserted into the power socket
correctly.
If you cannot identify the cause of the operating anomaly:
switch off the appliance (do not subject it to rough treatment)
and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I fi nd it?
It is important that you inform the Assistance Service of your
product code and its serial number (a 16-character code which
begins with the number 3); this can be found on the guarantee
certifi cate or on the data plate located inside the appliance.
This will help to avoid wasted journeys being made by
technicians, thereby (and most signifi cantly) saving the cor-
responding callout charges.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 19 -