DL manuals
D-Link
Switch
DGS-1008P
Quick installation manual

D-Link DGS-1008P Quick installation manual - Lis

Other manuals for DGS-1008P: Selection Manual, User Manual, Quick Installation Manual, Quick Installation Manual, Quick installation manual, Quick installation manual, User Manual

Page of 8

Download

Print this page

Bookmark us

DGS-1008P

LIS

LED INDICATORS

The LED indicators allow you to monitor, diagnose, and troubleshoot any potential problem within the

switch, connection, or attached devices.

LED

Color

Status

Description

Power

Green

Solid light

Power on

Off

Power off

Link/Act/Speed

Green

Solid light

Connection to a 1000 Mbps Ethernet device.

Blinking

The port is receiving or transmitting data.

Amber

Solid light

Connection to a 10/100 Mbps Ethernet device.

Blinking

The port is receiving or transmitting data.

Off

Light off

No link

PoE ( Ports1 to 4 )

Green

Solid light

The port is successfully connected to a PoE

device and is powering the device properly.

Off

No connection to a PoE device

Red

Blinking

Power management mode:

A valid PoE load is connected to port output

lines, but the switch does not have sufficient

power for supplying the required load power.

Port power is not activated

Solid Light

Overload or short circuit is detected on port

output lines. Port power is not activated

PoE Max.

Red

Solid light

Total power consumption is above 66W.

Blinking

Output power to PoE devices has exceeded the

maximum power budget (68W).

Off

Light off

Total power consumption is below Power Guard

Band (66W).

« ‹ Prev 2 3 4 5 6 7 8 Next › »

Summary of DGS-1008P

Page 1
8-port gigabit unmanaged desktop switch dgs-1008p quick installation guide.
Page 2: Package
Dgs-1008p 2 en g li s h package contents contents if any of these items are missing from your packaging, contact your reseller. Warning: using a power adapter with a different voltage rating will damage and void the warranty of this product. • dgs-1008p 8-port gigabit unmanaged desktop switch • powe...
Page 3: Lis
Dgs-1008p 3 en g lis h product setup before setting up the dgs-1008p please follow the steps below to set up the switch: 1. Install the dgs-1008p in a cool and dry place. Refer to the technical specifications for the acceptable operating temperature and humidity ranges. 2. Install the switch in a si...
Page 4
Dgs-1008p 4 en g li s h connecting the dgs-1008p to your network a. Power plug the ac power cord into a free outlet or surge protector, then plug the other end of the dc power jack into the power port of the dgs-1008p. The power led will illuminate confirming that the device has powered up successfu...
Page 5: Lis
Dgs-1008p 5 en g lis h led indicators the led indicators allow you to monitor, diagnose, and troubleshoot any potential problem within the switch, connection, or attached devices. Led color status description power green solid light power on off power off link/act/speed green solid light connection ...
Page 6: Troubleshooting
Dgs-1008p 6 en g li s h troubleshooting setup and configuration problems 1. What should i do if the power led does not light up? - check if the power adapter is connected properly to the outlet or surge protector and the back of the device. - ensure that the on/off switch is in the "on" position. 2....
Page 7: Lis
Dgs-1008p 7 en g lis h notes.
Page 8: Technical Support
Version 4.00(us)_130x183 october 27, 2016 copyright ©2016 all rights reserved. D-link and the d-link logo are registered trademarks of d-link corporation or its subsidiaries. Other trademarks are the property of their respective owners. Product specifications, size and shape are subject to change wi...