1. DL manuals
  2. D-Link
  3. IP Phone
  4. DVG-5121SP
  5. User Manual

D-Link DVG-5121SP User Manual

Summary of DVG-5121SP

  • Page 1

    D-link dvg-5121sp voip telephone adapter user manual building networks for people recyclable 2006/11/ 27 ver. 1.00

  • Page 2

    Table of content dvg-5121sp user’s manual d-link corporation 2 1. Introduction 1-1. Product overview..…..................................................................................................5 1-2. Product features……………………………..……………….……………………………6 1-3. Hardware description………………………………………………...

  • Page 3

    Table of content dvg-5121sp user’s manual d-link corporation 3 5-4. Upnp setting……………………………………………………………………………...39 5-5. Route static route………………………………………………………………………………….….40 5-6. Security 5-6-1. Mac filter………………………………………………………………………………..42 5-6-2. Ip filter…………………………………………………………………………………..43 5-6-3. ...

  • Page 4

    Table of content dvg-5121sp user’s manual d-link corporation 4 8-6. Firmware…………………………………………………………………………………...72 8-7. Device setting……………………………………………………………………………..73 9. Status 9-1. Device information………………………………………………………………………..74 9-2. Log………………………………………………………………………………………….75 9-3. Status………………………………...

  • Page 5: 1. Introduction

    Introduction dvg-5121sp user’s manual d-link corporation 5 1. Introduction 1-1. Product overview d-link®, an industry leader in networking, introduces dvg-5121sp voip telephone adapter for the home environment. The dvg-5121sp voip telephone adapter converts any existing analog (cord or cordless) tel...

  • Page 6

    Introduction dvg-5121sp user’s manual d-link corporation 6 1-2. Product features wan: one rj-45 10/100mbps auto-mdi/mdix ethernet port wan type: static ip, pppoe, dhcp, pptp, big pond, pptp client vpn pass through qos: ip precedence, diffserv nat traversal: outbound proxy, stun, upnp sip and rtp pri...

  • Page 7

    Introduction dvg-5121sp user’s manual d-link corporation 7 voice pond key sipv2 (rfc3261) compliance sip method: ack, bye, cancel, info, invite, notify, options, ping, prack, refer, register, subscribe, update sip extension: session timer, proxy-require, p-asserted (rfc3325), mwi (rfc3842) voice com...

  • Page 8

    Introduction dvg-5121sp user’s manual d-link corporation 8 1-3. Diagnostic leds and external interfaces front panel wan led when a connection is established, this led is on. The led will blink to indicate network traffic is passing through the wan port. If the led does not light up when a cable is c...

  • Page 9

    Introduction dvg-5121sp user’s manual d-link corporation 9 rear panel side panel wan port this port connects to your broadband modem or router through an ethernet cable. Lan port this port connect to an ethernet enabled computer/ ip sharing device using ethernet cabling. Reset this button is used to...

  • Page 10

    Introduction dvg-5121sp user’s manual d-link corporation 10 warning: to avoid any possible damage to your dvg-5121sp devices, do not connect the phone 2 port to a wall phone line. If any of these are done, your dvg-5121sp may be damaged. Restore to factory default: a reset button is provided on the ...

  • Page 11: 2. Before You Begin

    Before you begin dvg-5121sp user’s manual 11 d-link corporation 2. Before you begin 2-1. Package contents check the content of your dvg-5121sp package: dvg-5121sp voip telephone adapter cat5 ethernet cable* 1 cd-rom standard rj-11 phone cable*1 quick installation guide 12vdc 1.25a power adapter if a...

  • Page 12

    Installation and applications dvg-5121sp user’s manual 12 d-link corporation 3. Installation and applications 3-1. Voip telephone adapter assigned with a public ip address the voip telephone adapter will have a public ip address for internet connection regardless of whether it is a static ip address...

  • Page 13

    Installation and applications dvg-5121sp user’s manual 13 d-link corporation 3-2. Voip telephone adapter in a nat network the voip telephone adapter uses a virtual ip address and the ip sharing function of other systems to connect to the internet. Lan ip address of ip sharing please avoid ip address...

  • Page 14

    Installation and applications dvg-5121sp user’s manual 14 d-link corporation 3-3. Telephone interface description example: dvg-5121sp connecting directly to phone sets after connecting telephone sets to p1-p2, users can make direct calls, (p1-p2 are fxs interfaces). Each set acts as an independent i...

  • Page 15

    Installation and applications dvg-5121sp user’s manual 15 d-link corporation 3-4. Setting up the dvg-5121sp using a web browser the factory default lan port ip address is 192.168.1.1 instructions step1. Open an internet browser. Step2. Enter voip telephone adapter’s wan port ip address in the websit...

  • Page 16

    Installation and applications dvg-5121sp user’s manual 16 d-link corporation the dvg-5121sp voip telephone adapter doesn’t allow multiple people to configure the voip telephoneadapter at the same time. If a user already logged into the system, other users from different ip addresses cannot login at ...

  • Page 17: 4. Basic Network Settings

    Basic network settings dvg-5121sp user’s manual d-link corporation 17 4. Basic network settings 4-1. Wan the network settings are used to set the voip telephone adapter’s communication ports, ip configurations, adsl service setting, ip tunneling and etc. You might refer to the following pages for di...

  • Page 18

    Basic network settings dvg-5121sp user’s manual d-link corporation 18 4-1-2. Dhcp dhcp stands for "dynamic host configuration protocol". Dhcp's purpose is to enable individual computers on an ip network to extract their configurations from a server (the 'dhcp server') or servers, in particular, serv...

  • Page 19

    Basic network settings dvg-5121sp user’s manual d-link corporation 19 wan port mac: the default mac address is set to the wan’s physical interface mac address on the voip telephone adapter. It is not recommended that you change the default mac address unless required by your isp. The default mac add...

  • Page 20

    Basic network settings dvg-5121sp user’s manual d-link corporation 20 4-1-3. Pppoe (dsl) point to point protocol over ethernet is a proposal specifying how a host personal computer (pc) interacts with a broadband modem (i.E. Xdsl, cable, wireless, etc) to achieve access to the growing number of high...

  • Page 21

    Basic network settings dvg-5121sp user’s manual d-link corporation 21 wan port mac: the default mac address is set to the wan’s physical interface mac address on the voip telephone adapter. It is not recommended that you change the default mac address unless required by your isp. The default mac add...

  • Page 22

    Basic network settings dvg-5121sp user’s manual d-link corporation 22 open your web browser and enter the url http://192.168.1.1 in the address bar and press enter. Enter “admin” as the username and click login to enter the device’s web gui. No password needed. Click basic network settings and then ...

  • Page 23

    Basic network settings dvg-5121sp user’s manual d-link corporation 23 click submit at the bottom of the page. The system will restart after you click submit.. After restarting, the web gui will return to the login page, and the pppoe settings you entered will be displayed after.

  • Page 24

    Basic network settings dvg-5121sp user’s manual d-link corporation 24 4-1-4. Pptp pptp stands for point to point tunneling protocol. It was developed by a consortium including microsoft and is used for establishing vpn (virtual private network) tunnels across the internet. This allows remote users t...

  • Page 25

    Basic network settings dvg-5121sp user’s manual d-link corporation 25 wan port mac: the default mac address is set to the wan’s physical interface mac address on the voip telephone adapter. It is not recommended that you change the default mac address unless required by your isp. The default mac add...

  • Page 26

    Basic network settings dvg-5121sp user’s manual d-link corporation 26 max idle time: enter a maximum idle time during which the internet connection is maintained during inactivity. To disable this feature, enable auto-reconnect. Set dns server: enter the primary and secondary dns server addresses..

  • Page 27

    Basic network settings dvg-5121sp user’s manual d-link corporation 27 4-1-5. L2tp layer two tunneling protocol (l2tp) is an extension of the point-to-point tunneling protocol (pptp) used by an internet service provider (isp) to enable the operation of a virtual private network (vpn) over the interne...

  • Page 28

    Basic network settings dvg-5121sp user’s manual d-link corporation 28 required by your isp. The default mac address is set to the wan’s physical interface mac address on the voip telephone adapter. You can use the “clone mac address” button to copy the mac address of the ethernet card installed by y...

  • Page 29

    Basic network settings dvg-5121sp user’s manual d-link corporation 29 4-1-6. Big pond this service is supported in australia only. Wan port ip assignment: big pond. Host name: the host name is optional but may be required by some isps. The default host name is the device name of the router and may b...

  • Page 30

    Basic network settings dvg-5121sp user’s manual d-link corporation 30 mac address of the ethernet card installed by your isp and replace the wan mac address with the mac address of the router. Ping from wan: while enable, it allows end user ping from wan through internal to check the device working ...

  • Page 31

    Basic network settings dvg-5121sp user’s manual d-link corporation 31 4-2. Lan lan setting this section will allow you to change the local network settings of the router and to configure the dhcp settings. Lan ip address: enter the ip address of the router. The default ip address is 192.168.1.1.If y...

  • Page 32

    Basic network settings dvg-5121sp user’s manual d-link corporation 32 4-3. Dhcp server 4-3-1. Dhcp server setting stands for dynamic host control protocol. The dvg-5121sp has a built-in dhcp server. The dhcp server will automatically assign an ip address to the computers on the lan/ private network....

  • Page 33

    Basic network settings dvg-5121sp user’s manual d-link corporation 33 assigned dhcp ip address- set the starting ip address and the ending ip address for the dhcp server’s ip assignment lease time- the length of time for the ip lease. Enter the lease time. The default setting is one hour 4-3-2. Dhcp...

  • Page 34

    Advance network settings dvg-5121sp user’s manual d-link corporation 34 5. Advance network settings 5-1. Nat nat setting nat setting- user can choose what kind of nat type need to support in this page..

  • Page 35

    Advance network settings dvg-5121sp user’s manual d-link corporation 35 5-2. Virtual server setting virtual server- select enabled or disabled name- enter the name referencing the virtual service private ip- the server computer in the lan (local area network) that will be providing the virtual servi...

  • Page 36

    Advance network settings dvg-5121sp user’s manual d-link corporation 36 schedule- the schedule of time when the virtual service will be enabled. The schedule may be set to always, which will allow the particular service to always be enabled. If it is set to time, select the time frame for the servic...

  • Page 37

    Advance network settings dvg-5121sp user’s manual d-link corporation 37 5-3. Application setting some applications require multiple connections, such as internet gaming, video conferencing, internet telephony and others. These applications have difficulties working through nat (network address trans...

  • Page 38

    Advance network settings dvg-5121sp user’s manual d-link corporation 38 trigger port: this is the port used to trigger the application. It can be either a single port or a range of ports. Trigger type: this is the protocol used to trigger the special application. Public port: this is the port number...

  • Page 39

    Advance network settings dvg-5121sp user’s manual d-link corporation 39 5-4. Upnp setting choose upnp function status. Upnp use the universal plug and play feature click on enabled. Upnp provides compatibility with networking equipment, software and peripherals of the over 400 vendors that cooperate...

  • Page 40

    Advance network settings dvg-5121sp user’s manual d-link corporation 40 5-5. Route static route if the wan of the ip sharing device has static ip address, then the nat ip address is set as the public ip address of the ip sharing. Static route- select enabled or disabled type- choose net or host to d...

  • Page 41

    Advance network settings dvg-5121sp user’s manual d-link corporation 41 5-6. Security 5-6-1. Mac filter use mac (media access control) filters to allow or deny lan (local area network) computers by their mac addresses from accessing the network. You can either manually add a mac address or select th...

  • Page 42

    Advance network settings dvg-5121sp user’s manual d-link corporation 42 5-6-2. Ip filter filters are used to deny or allow lan (local area network) computers from accessing the internet. The dvg-5121sp can be setup to deny internal computers by their ip or mac addresses. The dvg-5121sp can also bloc...

  • Page 43

    Advance network settings dvg-5121sp user’s manual d-link corporation 43 5-6-3. Url filter url filter- select enabled or disabled. Fill up with the start ip you would like to allow/deny..

  • Page 44

    Advance network settings dvg-5121sp user’s manual d-link corporation 44 5-6-4. Domain filter domain filter- select enabled or disabled. Fill up with the ip range you would like to allow/deny..

  • Page 45

    Advance network settings dvg-5121sp user’s manual d-link corporation 45 5-6-5. Firewall firewall- select enabled or disabled. Active- select yes or no action- select allow or deny source- choose wan or lan as the source and enter a range of ip addresses out on the internet that you would like this r...

  • Page 46

    Advance network settings dvg-5121sp user’s manual d-link corporation 46 network that you want to allow the incoming service to. This will not work with a range of ip addresses . Enter the port or range of ports that are required to be open for the incoming service. Schedule- this is the schedule of ...

  • Page 47

    Advance network settings dvg-5121sp user’s manual d-link corporation 47 5-6-6. Rule summary check all security setting rule summary in this page..

  • Page 48: 6. Sip Setting

    Sip setting dvg-5121sp user’s manual d-link corporation 48 6. Sip setting 6-1. Basic setting: sip port number - also called an outbound proxy, handles sip call signaling as a standard sip proxy server. It receives and transmits phone conversation traffic (media) in between two talking voip telephone...

  • Page 49

    Sip setting dvg-5121sp user’s manual d-link corporation 49 session timer- it is to avoid the billing of abnormal dropping the call because of internet. The default is disabled. Default: 1800 seconds media port start- type the beginning of the listening port range media port end- type the end of the ...

  • Page 50

    Sip setting dvg-5121sp user’s manual d-link corporation 50 6-2. Account setting: authentication expired time- time for authentication expired. Default: 3600 seconds invite with id / account- dvg-5121sp can be invited to a voip trunk voip telephone adapter w/o register to a proxy. Please contact your...

  • Page 51

    Sip setting dvg-5121sp user’s manual d-link corporation 51 6-3. Nat traversal: enable stun- using stun protocol prevents problems with setting the ip sharing function, but some nat do not support this protocol. Enable upnp- to enable the voip telephone adapter’s ip traffic to pass through a nat serv...

  • Page 52: 7. Voip Setting

    Voip setting dvg-5121sp user’s manual d-link corporation 52 7. Voip setting 7-1. Voice setting: codec priorities- use this field to select the type of voice coder/decoder (codec) priority you want to use. G.711/ ulaw: operates at 64 kbps (standard), 56 kbps, and 48 kbps (non-standard). Compresses fr...

  • Page 53

    Voip setting dvg-5121sp user’s manual d-link corporation 53 g.729a: operates on 10ms frames with short algorithm delays. Compresses 8 khz codec or linear audio data to 8 kbps. Ilbc:internet low bit rate codec (ilbc) is a royalty free narrowband speech codec. Operates at 15.20 kbps. Rtp: real time tr...

  • Page 54

    Voip setting dvg-5121sp user’s manual d-link corporation 54 7-2. Call service: call waiting- select enabled or disabled. Default is: disable. Call waiting timeout- the waiting timeout can be set if user choose call waiting function enabled. Default is: 30 seconds. Attended transfer timeout- the atte...

  • Page 55

    Voip setting dvg-5121sp user’s manual d-link corporation 55 line to receive any inbound calls, the function can be disabled. Users can also use the up or down key to adjust hunting priority. Call hunting timeout- the call repeat timeout can be set if user choose call hunting group function enabled. ...

  • Page 56

    Voip setting dvg-5121sp user’s manual d-link corporation 56 7-3. Phone setting tone setting- select local area to tone type setting. Caller id type- select fsk type. In most cases, bellcore is preferred in north america and etsi in europe. Note: if you register the voip telephone adapter to a proxy,...

  • Page 57

    Voip setting dvg-5121sp user’s manual d-link corporation 57 caller id type 1 alerting signal- select alerting signal type to device 1. Caller id type 2 alerting signal- select alerting signal type to device 2. Ring impedance- select ring impedance base on local settings. Pls contact to isp. Hook fla...

  • Page 58

    Voip setting dvg-5121sp user’s manual d-link corporation 58 7-4. E.164 setting enable the e.164 function. Entry the county and area code in to the blank then “submit” settings. Country code- users please select the desired country code. Area code- please enter the area code. E.164 numbering: to invi...

  • Page 59

    Voip setting dvg-5121sp user’s manual d-link corporation 59 7-5. Fax setting : voice- voice data . T.38 fax relay- integrated and tested with fax data modems at rates of up to 14.4 kbps. Udp and tcp support. Voice and t.38 fax relay : both of voice and t.38 fax relay voice and t.38 fax pass through:...

  • Page 60

    Voip setting dvg-5121sp user’s manual d-link corporation 60 7-6. General dialing setting inter-dlight timeout- default 4 sec first-dlight timeout- default 16 sec transfer key- default *# new call key- ** three way conference key- default *3 hold call key- when users takes european type, please selec...

  • Page 61

    Voip setting dvg-5121sp user’s manual d-link corporation 61 7-7. Qos/tos setting : qos: quality of service ( qos) refers to both a network’s ability to deliever data with minimum delay, and the networking method used to provide bandwidth for real-time multimedia applications. Tos: network traffic ca...

  • Page 62

    Voip setting dvg-5121sp user’s manual d-link corporation 62 tos y qos (quality of service): sets an external bandwidth to ensure sound quality during transmission (when this function is enabled, the voice packet has the highest priority to ensure telecommunication quality while less bandwidth is ass...

  • Page 63

    Voip setting dvg-5121sp user’s manual d-link corporation 63 diffserv setting y tos/diffserv (type of service/dscp): the voice packet has the highest priority to ensure telecommunication quality; the larger the value you set, the higher priority you will get. Sip tos- select enabled or disabled. Defa...

  • Page 64

    Voip setting dvg-5121sp user’s manual d-link corporation 64 7-8. Phone book user can set phone book themselves by 50sets no. Provides shortcuts for dialing frequently used (voip) phone number #0 ~ #9, total 10 digit list to support speed dial..

  • Page 65

    Voip setting dvg-5121sp user’s manual d-link corporation 65 7-9. Call screen: enter reject incoming phone number & reject outgoing phone number in this page..

  • Page 66: 8. Tools

    Tools dvg-5121sp user’s manual d-link corporation 66 8. Tools 8-1. Admin: account level: select one of account levels as for admin, user, and guest account name: enter the name to manage account account password: enter the pass phrase to be used for authentication. Confirm password: reenter the pass...

  • Page 67

    Tools dvg-5121sp user’s manual d-link corporation 67 8-2. Page configure: web page authority setting- choose one of the pages from below page items and conduct a view and configure level as admin, user, guest and non authority to manage the voip terminal adapter web page..

  • Page 68

    Tools dvg-5121sp user’s manual d-link corporation 68 8-3. Date/time: manual: to manually input the time iption and enter the values for the year, month, day, hour, minute, and second. Click the computer clock button, to copy your computer’s time. Ntp: ntp is shourt for network time protocol. Ntp syn...

  • Page 69

    Tools dvg-5121sp user’s manual d-link corporation 69 ntp time server settings: choose which time zone in located area, set ntp server address to update network local time by system automatically.

  • Page 70

    Tools dvg-5121sp user’s manual d-link corporation 70 8-4. Ddns: dynamic domain name system is a method of keeping a domain name linked to a changing ip address. This is a useful feature since many computers do not use a static ip address. To use the ddns update client built into the router, click on...

  • Page 71

    Tools dvg-5121sp user’s manual d-link corporation 71 8-5. System: pin test: the voip terminal adapter offers you to conduct a ping test by enter the host name or an ip address then click ping. Save/restore setting: click save/restore to save/restore the current settings to the local hard drive. Fact...

  • Page 72

    Tools dvg-5121sp user’s manual d-link corporation 72 8-6. Firmware: you can upgrade the firmware of the voip terminal adapter here. Make sure the firmware you want to use is on the local hard drive of the computer. Please check the d-link support site for firmware updates at http://support.Dlink.Com...

  • Page 73

    Tools dvg-5121sp user’s manual d-link corporation 73 8-7. Device setting: bridge or router mode settings: user can choose network mode and some user settings in this page..

  • Page 74: 9. Status:

    Status dvg-5121sp user’s manual d-link corporation 74 9. Status: 9-1. Device information this page displays the current information for the dvg-5121sp.

  • Page 75

    Status dvg-5121sp user’s manual d-link corporation 75 9-2. System log: the voip terminal adapter keeps a running log of events and activities occurring on the voip. If the device is rebooted, the logs are automatically cleared..

  • Page 76

    Status dvg-5121sp user’s manual d-link corporation 76 9-3. Line status: this page displays the current information for the line status..

  • Page 77

    Status dvg-5121sp user’s manual d-link corporation 77 9-4. Cdr: this page containing information about recent system usage such as the identities of sources (points of origin), the identities of destinations (endpoints), the duration of each call, the amount billed for each call, the total usage tim...

  • Page 78: 10. Telnet

    Introduction dvg-5121sp user’s manual d-link corporation 78 10. Telnet run telnet- enable the telnet control interface, run the function key as: telnet 192.168.1.1 when user wants to use the telnet interface to do the settings, it’s necessary to totally log out from the web page control because the ...