2 d-link ebr-2310 user manual table of contents table of contents product overview ........................................................4 package contents ...................................................4 system requirements .............................................4 introduction ............
3 d-link ebr-2310 user manual table of contents networking basics ....................................................60 check your ip address ..........................................60 statically assign an ip address .............................61 technical specifications ...........................
4 d-link ebr-2310 user manual section 1 - product overview • ebr-2310 ethernet broadband router • power adapter • ethernet cable • manual on cd system requirements • ethernet-based cable or dsl modem • computers with windows ® , macintosh ® , or linux-based operating systems with an installed ethern...
5 d-link ebr-2310 user manual section 1 - product overview introduction the d-link express ethernetwork ebr-2310 is a 4-port ethernet broadband router. The d-link ebr-2310 enables users to quickly and easily share a high speed internet connection. The d-link ebr-2310 also incorporates many advanced ...
6 d-link ebr-2310 user manual section 1 - product overview • advanced firewall & parental control features - the web-based user interface displays a number of advanced network management features including: • content filtering - easily applied content filtering based on mac address, url and/or domain...
7 d-link ebr-2310 user manual section 1 - product overview hardware overview front panel power power indicator will light green. Wan wan status indicator will light green when there is good physical wan connection. Lan link/act. Link status indicators light green. The led flickers when the correspond...
8 d-link ebr-2310 user manual section 1 - product overview reset used to restore the ebr-2310 back to factory default settings. Rear panel *all ports (both lan & wan) are auto-mdix. All ports auto-sense cable types to accommodate straight-through or cross-over cable. Power connect one end of your in...
9 d-link ebr-2310 user manual section 1 - product overview technology introduction introduction to broadband router technology a router is a device that forwards data packets from a source to a destination. Routers forward data packets using ip addresses and not a mac address. A router will forward ...
10 d-link ebr-2310 user manual section 1 - product overview introduction to local area networking local area networking (lan) is the term used when connecting several computers together over a small area such as a building or group of buildings. Lan’s can be connected over large areas. A collection ...
11 d-link ebr-2310 user manual section 2 - installation installation getting started installation location the ebr-2310 can be positioned at any convenient place in your office or house. No special wiring or cooling requirements are needed. However, you should comply with the following guidelines: • ...
12 d-link ebr-2310 user manual section 3 - configuration configuration the ebr-2310 provides an embedded web-based management utility making it operating system independent. You can configure your ebr-2310 through the netscape communicator or internet explorer browser in ms windows ® , macintosh, linux...
13 d-link ebr-2310 user manual section 3 - configuration setup wizard you may run the setup wizard to quickly setup your router. Click setup wizard to launch the wizard. Click launch internet connection setup wizard to begin. Click next to continue..
14 d-link ebr-2310 user manual section 3 - configuration create a new password and then click next to continue. Select your time zone from the drop-down menu and then click next to continue. Select the type of internet connection you use and then click next to continue..
15 d-link ebr-2310 user manual section 3 - configuration if you selected dynamic, you may need to enter the mac address of the computer that was last connected directly to your modem. If you are currently using that computer, click clone your pc’s mac address and then click next to continue. The host...
16 d-link ebr-2310 user manual section 3 - configuration if you selected l2tp, enter your l2tp username and password. Click next to continue. If you selected static, enter your network settings supplied by your internet provider. Click next to continue. Click connect to save your settings. Once the r...
17 d-link ebr-2310 user manual section 3 - configuration enter the ip address assigned by your isp. Enter the subnet mask assigned by your isp. Enter the gateway assigned by your isp. The default mac address is set to the wan’s physical interface mac address on the broadband router. It is not recomme...
18 d-link ebr-2310 user manual section 3 - configuration choose dynamic ip address to obtain ip address information automatically from your isp. Select this option if your isp does not give you any ip numbers to use. This option is commonly used for cable modem services. The host name is optional but...
19 d-link ebr-2310 user manual section 3 - configuration select dynamic (most common) or static. Select static if your isp assigned you the ip address, subnet mask, gateway, and dns server addresses. Enter your pppoe user name. Enter your pppoe password and then retype the password in the next box. E...
20 d-link ebr-2310 user manual section 3 - configuration select dynamic (most common) or static. Select static if your isp assigned you the ip address, subnet mask, gateway, and dns server addresses. Enter the ip address (static pptp only). Enter the primary and secondary dns server addresses (static...
21 d-link ebr-2310 user manual section 3 - configuration select dynamic (most common) or static. Select static if your isp assigned you the ip address, subnet mask, gateway, and dns server addresses. Enter the ip address (static l2tp only). Enter the primary and secondary dns server addresses (static...
22 d-link ebr-2310 user manual section 3 - configuration enter your big pond user name. Enter your big pond password and then retype the password in the next box. Enter the ip address of the login server. Enter the ip address of the login server. The default mac address is set to the wan’s physical i...
23 d-link ebr-2310 user manual section 3 - configuration port forwarding rules this will allow you to open a single port or a range of ports. Check the box to enabled the rule. Enter a name for the rule. Enter the ip address of the computer on your local network that you want to allow the incoming se...
24 d-link ebr-2310 user manual section 3 - configuration application rules some applications require multiple connections, such as internet gaming, video conferencing, internet telephony and others. These applications have difficulties working through nat (network address translation). Special applica...
25 d-link ebr-2310 user manual section 3 - configuration network filter select disable mac filters, allow mac addresses listed below, or deny mac addresses listed below. Enter the mac address you would like to filter. To find the mac address on a computer, please refer to the networking basics section i...
26 d-link ebr-2310 user manual section 3 - configuration select turn website filtering off, turn website filtering on and allow access, or turn website filtering on and deny access. Enter the keywords or urls that you want to block (or allow). Any url with the keyword in it will be blocked. Configure web...
27 d-link ebr-2310 user manual section 3 - configuration check this box to enable dmz. Enter the ip address of the computer you would like to open all ports to. Check this box to allow pptp vpn traffic to pass through the router to your vpn client. Check this box to allow l2tp vpn traffic to pass throu...
28 d-link ebr-2310 user manual section 3 - configuration to use the universal plug and play (upnp ™ ) feature click on enabled. Upnp provides compatibility with networking equipment, software and peripherals. Unchecking the box will not allow the wbr- 2310 to respond to pings. Blocking the ping may p...
29 d-link ebr-2310 user manual section 3 - configuration enter the new password for the administrator login. The administrator can make changes to the settings. Enter the new password for the user login. If you login as the user, you can only see the settings, but cannot change them. Remote managemen...
30 d-link ebr-2310 user manual section 3 - configuration time settings ntp is short for network time protocol. Ntp synchronizes computer clock times in a network of computers. This field is optional. To manually input the time, enter the values in these fields for the year, month, day, hour, minute, an...
31 d-link ebr-2310 user manual section 3 - configuration system settings use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the save button. You will then see a file dialog, where you can select a location and file name...
32 d-link ebr-2310 user manual section 3 - configuration firmware upgrade click on the link in this screen to find out if there is an updated firmware; if so, download the new firmware to your hard drive. After you have downloaded the new firmware, click browse in this window to locate the firmware update...
33 d-link ebr-2310 user manual section 3 - configuration system check vct is an advanced feature that integrates a lan cable tester on every ethernet port on the router. Through the graphical user interface (gui), vct can be used to remotely diagnose and report cable faults such as opens, shorts, swa...
34 d-link ebr-2310 user manual section 3 - configuration device information this page displays the current information for the wbr-2310. It will display the lan, wan, and wireless information. If your wan connection is set up for a dynamic ip address then a release button and a renew button will be d...
35 d-link ebr-2310 user manual section 3 - configuration log first page: last page: previous: next: clear: view the first page of the log. View the last page of the log. View the previous page. View the next page. Clear the log..
36 d-link ebr-2310 user manual section 3 - configuration stats the screen below displays the traffic statistics. Here you can view the amount of packets that pass through the wbr-2310 on both the wan and the lan ports. The traffic counter will reset if the device is rebooted..
37 d-link ebr-2310 user manual section 3 - configuration support.
38 d-link ebr-2310 user manual section 5 - troubleshooting troubleshooting this chapter provides solutions to problems that can occur during the installation and operation of the ebr-2310. Read the following descriptions if you are having problems. (the examples below are illustrated in windows ® xp...
39 d-link ebr-2310 user manual section 5 - troubleshooting • configure your internet settings: • go to start > settings > control panel. Double-click the internet options icon. From the security tab, click the button to restore the settings to their defaults. • click the connection tab and set the di...
40 d-link ebr-2310 user manual section 5 - troubleshooting 3. Why can’t i connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as ebay, banking sites, and hotmail, we suggest ...
41 d-link ebr-2310 user manual section 5 - troubleshooting you should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various tcp/ip headers. For example, lets say tha...
42 d-link ebr-2310 user manual appendix a - assigning a static ip address assigning a static ip address (for windows ® 2000/xp) note: broadband routers will automatically assign ip addresses to the computers on the network, using dhcp (dynamic host configuration protocol) technology. If you are using...
43 d-link ebr-2310 user manual appendix a - assigning a static ip address • right-click on local area connections. • double-click properties • highlight internet protocol(tcp/ip) • click properties • select use the following ip address in the internet protocol (tcp/ip) properties window (shown below...
44 d-link ebr-2310 user manual appendix a - assigning a static ip address • input your ip address and subnet mask. (the ip addresses on your network must be within the same range. For example, if one computer has an ip address of 192.168.0.2, the other computers should have ip addresses that are seq...
45 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp adding and sharing printers in windows ® xp after you have run the network setup wizard on all the computers in your network (please see the network setup wizard section at the beginning of networking basics,) yo...
46 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp • click on add a printer • click next.
47 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp • select local printer attached to this computer • (deselect automatically detect and install my plug and play printer if it has been selected.) • click next • select use the following port: • from the pull-down ...
48 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp • select and highlight the correct driver for your printer. • click next (if the correct driver is not displayed, insert the cd or floppy disk that came with your printer and click have disk.) • at this screen, yo...
49 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp this screen gives you information about your printer. (the printer will begin to print a test page) click finish when the test page has printed, click ok.
50 d-link ebr-2310 user manual appendix b - adding and sharing printers in windows ® xp • go to start> printers and faxes a successful installation will display the printer icon as shown at right. You have successfully added a local printer..
51 d-link ebr-2310 user manual appendix c - sharing a network printer sharing a network printer after you have run the network setup wizard on all the computers on your network, you can run the add printer wizard on all the computers on your network. Please follow these directions to use the add pri...
52 d-link ebr-2310 user manual appendix c - sharing a network printer • select network printer • click next • select browse for a printer • click next • select the printer you would like to share. • click next.
53 d-link ebr-2310 user manual appendix c - sharing a network printer • click finish to check for proper installation: • go to start > printers and faxes.
54 d-link ebr-2310 user manual appendix c - sharing a network printer the printer icon will appear at right, indicating proper installation. You have completed adding the printer. To share this printer on your network: • remember the printer name • run the add printer wizard on all the computers on ...
55 d-link ebr-2310 user manual appendix d - sharing an lpr printer sharing an lpr printer to share an lpr printer (using a print server,) you will need a print server such as the dp-101p+. Please make sure that you have run the network setup wizard on all the computers on your network. To share an l...
56 d-link ebr-2310 user manual appendix d - sharing an lpr printer • from the pull-down menu, select standard tcp/ip port, as shown. • click next • please read the instructions on this screen. • click next • enter the printer ip address and the port name, as shown. • click next.
57 d-link ebr-2310 user manual appendix d - sharing an lpr printer • in this screen, select custom. • click settings • enter the port name and the printer name or ip address. • select lpr • enter a queue name (if your print-server/gateway has more than one port, you will need a queue name.) • click ...
58 d-link ebr-2310 user manual appendix d - sharing an lpr printer • this screen will show you information about your printer. • click finish • select the printer you are adding from the list of printers. • insert the printer driver disk that came with your printer. • click have disk if the printer ...
59 d-link ebr-2310 user manual appendix d - sharing an lpr printer • you can rename your printer if you choose. It is optional. Please remember the name of your printer. You will need this information when you use the add printer wizard on the other computers on your network. • click next • select y...
60 d-link ebr-2310 user manual appendix e - networking basics networking basics check your ip address after you install your new d-link adapter, by default, the tcp/ip settings should be set to obtain an ip address from a dhcp server (i.E. Wireless router) automatically. To verify your ip address, p...
61 d-link ebr-2310 user manual appendix e - networking basics statically assign an ip address if you are not using a dhcp capable gateway/router, or you need to assign a static ip address, please follow the steps below: step 1 windows ® xp - click on start > control panel > network connections. Wind...
62 d-link ebr-2310 user manual appendix f - technical specifications standards • ieee 802.3 10base-t ethernet • ieee 802.3u 100base-tx fast ethernet • ieee 802.3 nway auto-negotiation vpn pass through / multi-sessions • pptp • l2tp • ipsec device management web-based – requires at least microsoft int...
63 d-link ebr-2310 user manual appendix g - contacting technical support contacting technical support d-link provides free technical support for customers within the united states and within canada for the duration of the warranty period on this product. U.S. And canadian customers can contact d-lin...
64 d-link ebr-2310 user manual appendix h - warranty warranty subject to the terms and conditions set forth herein, d-link systems, inc. (“d-link”) provides this limited warranty: • only to the person or entity that originally purchased the product from d-link or its authorized reseller or distribut...
65 d-link ebr-2310 user manual appendix h - warranty tampered with, defaced or removed; initial installation, installation and removal of the product for repair, and shipping costs; operational adjustments covered in the operating manual for the product, and normal maintenance; damage that occurs in...
66 d-link ebr-2310 user manual appendix i - registration registration product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.1 01/26/2006.